• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Intermittent starter issue - reattack

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Never thought I would be posting about something as simple as a starter issue but here I am nonetheless.

351w Explorer EFI, 4R70W, Explorer reduction starter.

I have an intermittent starter issue. Occasionally it will make a single click and not crank. It sounds like maybe the pawl is extending but the motor is not moving. Either that or I am hearing the solenoid click.

12v to starter from battery with zero voltage drop on crank.
Signal wire at solenoid shows 6v on start. (6v drop). Disconnected from solenoid, the signal wire shows 12v on start. This tells me I have a bad wire somewhere.
Good grounds from battery and starter.

I eliminated the TRS by bypassing it and getting the same negative result.
I eliminated my ignition by bypassing the Explorer EFI harness and getting a positive result.
I am able to use a screwdriver to connect the signal post on the solenoid to the main battery lug on the starter and it starts fine.

It is my understanding the PINK wire (explorer) carries start signal from IGN to TRS. Then R/LtBl (T/R-98) from TRS to starter solenoid. Is there some other routing I am not aware of that I can check?

I should mention I did change the starter with no change.



What else am I missing here?
 
Last edited:
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I was wrong about being wrong. Problem is more complex than I initially thought.
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Pink wire is resistance wire to coil. That wire is bypassed, and sends a full 12V to your coil during crank. This happens thru a brown? wire that's on your "I" (for ign) terminal on your relay. If you use that on the other trigger post of the starter relay, you will get that issue. Look for a red with blue wire near the starter relay. That should be the one triggering it.
 

Attachments

  • photo.jpg
    photo.jpg
    64.6 KB · Views: 60
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I think you may be referring to a stock Bronco starter relay rather than Explorer
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
I think you may be referring to a stock Bronco starter relay rather than Explorer

Yes, but if you rewired the bronco, and cut the pink wire in the dash to send power to the Explorer style starter you would have that issue... The starter or the relay may not be your problem. Where did the pink wire come from?
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
All the colored wires I mentioned were Explorer harness colors, I probably should have mentioned that initially. The R/BL (Bronco) from my IGN is what supplies 12v to the Explorer Pink then to TRS then to starter relay which is a single post setup.

FWIW, I do have my coil hooked up to the Explorer R+Pk in HOT+RUN from IGN (Gr+R?).
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You still running this through a separate relay/solenoid on the fender, or is the key wired straight to the new starter?

And pardon my temporary ignorance, but what's a TRS?
I can think of all kinds of things that fit. Trans Range Switch maybe? No clue.

Just wondering why, after more than 50 years of using the same Red w/blue color wire to run from the key to the starter system, and keeping it the same through the neutral safety switches, Ford would start to use a Pink wire anywhere in that circuit.
You sure that Pink wire isn't supposed to be an alternate start sensing wire for another part of the system, rather than the actual start circuit itself? Where else does it go?

I'm not really familiar with the Exploder stuff like I should be obviously, so I'm learning about it here.

Thanks

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
No Paul, I am running direct to the solenoid on the starter.

Ford didn't change much but we did by modifying their Explorer harness.

The Explorer, in its stock form did have R/LtBl going from IGN to a fuse where it changed to W/Pink then to a clutch where it changed to Pink and into the TRS (Transmission Range Sensor which also acts as the NSS). From the TRS, depending on the year, a R/LtBl or T/R goes to the starter motor solenoid.

Since we are not running the same fuse box or a clutch we end up with our IGN R/LtBl going straight to the Explorer Pink wire.

Looking at the Ford diagram, they did have a separate relay powering the solenoid whereas I do not. The gauge of the Explorer wires is super tiny, like PCM tiny. I wonder if I have been frying this small gauge wire using it to power the starter solenoid.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
According to this diagram, I should be running a 50A fuse to power the starter solenoid! Things are starting to make sense.

uploadfromtaptalk1456596803675.jpg
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
That solenoid draws a lot of current. What size wire are you using for it?
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I spliced in 14ga in places to integrate i to bronco, but the lines going to and from the TRS are 22ga at best. With no relay feeding the solenoid, all that power is going through the 22ga.

I'm only as good as my smallest gauge.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And the old design ignition switch is not exactly a powerhouse either. It's a lot of current to always run through the switching contacts.
Even Ford still (or at least did up to the Explorer) uses a fender-mounted relay as both a power switch for the starter solenoid, AND the usual convenient location for attaching bunches of wires for power from the battery.

Wouldn't hurt then to at least upgrade your wire gauge, but maybe even consider adding the relay back into the system.

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Relay is definitely going in. Upgrading wire gauge in harness is a bit more tricky considering specialized terminations etc. I will report back results with relay but I'm still concerned about damage, if any, done to existing wire from possible overloading.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Definitely a legitimate concern. But with luck, nothing is permanent and the fix is easy, and the new relay could probably work just fine with 22ga at that point.

But like always, when in doubt... Go big!:cool:

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Relay is in. I could previously duplicate the issue within 20 cycles; just got to 50 and decided to call it good.

Thanks for the helpful input guys.
 
Top