What have you done to your Bronco today?

[hunter1]

Got a lot done today. Radiator and shroud in, steering column and shaft, Hydroboost and clutch master cylinder in and bled.

 

[tasker]

One seat done, one to go!

 

[Speedrdr]

One seat done, one to go!
View attachment 935130

Looks great. And I’m guessing the heated seats will be much appreciated in the NE in winter.

R

 

[tasker]

Very much so!

 

[Speedrdr]

Very much so!

Yeah, 10 years ago I had zero interest in or use for heated seats…fast forward to now and it’s become a needed option on the wife’s car. My F-150 has cloth seats and warms up fast enough to not need heated seats.
May have to seriously consider heated seats in the Retirement Project.

R

 

[tasker]

No top and half vinyl doors....driven from late March till late November if I can help it...they will be used!

 

[skrit]

Installed new Tom Woods driveshafts front and rear.

Learned I actually need to use the 1/4 spacer plate that came with my TBP 4R70W mount for the front driveshaft. I know... if it's not touching leave it alone but this is too close!

Oh and I spilled some gear oil to add to my concrete stain collection.

 

[skrit]

No top and half vinyl doors....driven from late March till late November if I can help it...they will be used! View attachment 935263

I can't wait till I can do that!

 

[skrit]

Oops forgot I added this too... it's so shiny!

 

[gnsteam]

Installed new Tom Woods driveshafts front and rear.
View attachment 935264
Learned I actually need to use the 1/4 spacer plate that came with my TBP 4R70W mount for the front driveshaft. I know... if it's not touching leave it alone but this is too close!
View attachment 935265
Oh and I spilled some gear oil to add to my concrete stain collection.

I had to go with a 3/4" spacer with my Tom's crossmember. Your build is looking great.

 

[Howard2x4x4]

No top and half vinyl doors....driven from late March till late November if I can help it...they will be used! View attachment 935263

All that fur must help!

 

[mustanggarage]

started tearing it down for the Half cab install.

 

[Speedrdr]

Installed new Tom Woods driveshafts front and rear.
View attachment 935264
Learned I actually need to use the 1/4 spacer plate that came with my TBP 4R70W mount for the front driveshaft. I know... if it's not touching leave it alone but this is too close!
View attachment 935265
Oh and I spilled some gear oil to add to my concrete stain collection.

@skrit , does the CV joint cover come with the rear DS? Never seen one before.

Randy

 

[awest5321]

Th

Whipped up a fuel can rack from some 14 gauge.

This looks awsome. Been on my mind for awhile. Your design has inspired me to get busy.

 

[awest5321]

Fabbed up some front sway bar disconnects and finally put my 302 fender badges on.

 

[Soylent]

Removed and replaced my heater twice after resealing and getting the high output fan not to squeal. Also confirmed that self-tapping screws self tap. Pulled the box out a third time

 

[billh1289]

Installed the sliding glass in the hardtop. A lot of folks don’t like the look but I think they look decent and the kids are going to appreciate the extra air in the summer.

 

[Yeller]

Got out for some exercise

 

[hunter1]

Actually the last couple of evenings. Got the throttle cable installed and the pedal modified, cut the filler neck off and relocated it to the “side” of my PS reservoir and welded a new outlet for the delivery hose. Made my HB hoses and installed, and got most of the engine compartment wiring installed.

 

[hunter1]

Actually the last couple of evenings. Got the throttle cable installed and the pedal modified, cut the filler neck off and relocated it to the “side” of my PS reservoir and welded a new outlet for the delivery hose. Made my HB hoses and installed, and got most of the engine compartment wiring installed. View attachment 935651 View attachment 935652

Also got my dash modified to flip down and wired the switches up.