• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. Bronco-Brian

    SOLD Rear Cargo Floor Mat - TBP

    New Tom's Bronco Parts p/n 4302 rear bed mat. Going a different direction, decided not to use. $200 and buyer pays shipping (~$25).
  2. Bronco-Brian

    Explorer 4R70W to Dana 20, which adapter to use?

    I looked at my paperwork, I have the 2704-A kit. Glad you got clarification. I love the trans-bought a us shift to control it.
  3. Bronco-Brian

    Explorer 4R70W to Dana 20, which adapter to use?

    Advance Adapters has the right 4R70W kit already. I've used it. Yes you will need to cut about 3/4" off the transmission output shaft - not a big deal. This can be done without disassembly and using a cut off wheel. The stock trans crossmember will also require a modification. The kit...
  4. Bronco-Brian

    SOLD 66 Tailgate

    I've got a 66 tailgate that is dented/bent at the bottom, but pretty rust free. I'll get a pic soon.
  5. Bronco-Brian

    OR ‘72 Half Cab

    Definitely a rebody candidate. I think your price is in the ballpark. I guess it all depends what the next owner’s plans are.
  6. Bronco-Brian

    OR ‘72 Half Cab

    Hey all, I managed to check out this truck today. Owner has it on eBay now for $20k. Body is blown apart now, and I got a good look at the tub. Bed floor and the corner extension panels all need replacement. B-pillars are shot - lower A-pillars need patches. Rust holes are present in the...
  7. Bronco-Brian

    Ignition key problem

    Am I hearing you correctly, you replaced the key for the original tumbler? Outside the switch, the tumbler and key are fine - but assembled, it sticks?
  8. Bronco-Brian

    Best floor pan paint

    POR15, then an epoxy primer, then a polyurethane top coat of your color choice. If you leave a mat or carpet over the primer to prevent UV exposure you should also be OK. If not covering then bed liner over the epoxy is a good solution.
  9. Bronco-Brian

    SOLD 1” Lift Body Mounts

    Hi, I'll take them - I'm also in Portland. PM me where to meet up. Thanks, Brian
  10. Bronco-Brian

    Testing factory vacuum advance

    You might be getting too much full advance timing as mechanical advance is in addition to the vacuum advance (under certain load conditions) - have you checked with a timing light? It takes 10-15 inch of vacuum to pull the vac advance - you cannot create that much with your mouth. There is...
  11. Bronco-Brian

    body removal questions

    Tractor, did I hear Tractor - Here's what I had in my archives of Bronco restoration. Could also pick-up from side if your reach is too short, or capacity is limited. Note the bracing - A real easy point of attachment is the hood hinge points and bolt steel angle to p/u seat belt mounts in the...
  12. Bronco-Brian

    OR Off-road Bumpers

    Here's a set of front and rear bumpers that I probably will not be using. Photos show 3" body lift fitment that close the panel gaps, but can be altered to fit any body lift, or even no lift. They are a good base to begin custom metal work on. These are raised to meet the body at factory...
  13. Bronco-Brian

    CA set of 4 oem steel wheels

    Do you need 5.5" width, or 6"?
  14. Bronco-Brian

    OH Stock Pitman Arm

    I've got one in nice shape for 66-75 versions. $50 shipped to you in flat rate box.
  15. Bronco-Brian

    Toms Bronco parts 3.5 inch rear leaf 11 pack

    I have new TBP 11 pack rears, and removed the bottom 2 leafs. Truck sits much nicer now with my 3.5" front coils. If you later choose to run a heavier load, the leafs can always be reinstalled.
  16. Bronco-Brian

    SOLD 1966 Front Bench Seat - Silver

    Bump... If you are looking for original Matchstick upholstery, this is it. Original Ford OEM material sourced from SMS. Make me an offer on the seat. Probably be $200 to ship - depends on zip code.
  17. Bronco-Brian

    Chrome grill Placement question

    You can drill them all to 3/16”. I tend to drill the stud clips holes smaller. The 3 in the sides are all studs. So are the 2 center ones in the horizontal trim. Then you have 4 plastic clips in the horizontals top and another 4 bottom. 8 stud type and 8 plastic clips does the job.
  18. Bronco-Brian

    Chrome grill Placement question

    Another trick I've learned on non drilled grilles - place the trim where you want it, draw thin pencil line on both sides of the edges. Split the difference between the pencil lines to position the drill hole. Also note, the studs take a smaller hole than the push in clips.
  19. Bronco-Brian

    Top Requested New Bronco Colors

    Sorry to miss Lightning Blue - thought I had them all.
Top