• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. J

    Leaking oil pan drain plug

    Is your oil pan an '89 Mustang or early Bronco part? If you have an '89 Mustang pan this may be a good time to get the correct pan. Either way, there are over size self threading plugs to repair stripped or cross threaded oil drain holes.
  2. J

    exhaust routing, What's the best exit location?

    I've seen several including my own that backed into a rock, stump, or curb that bent the pipe against the tire putting a kink in the tube. I went with the '77 tail pipe pattern the exits just in front of the bumper pointed down and out.
  3. J

    Steering cancel Cam

    Pins were used in '78 and later turn signal switches to locate a ring in the switch. That ring includes the cancelling cams. I don't think the pins were intended to BE the cancelling cams. No surprise, they break the cancelling arms in the switch. gr8scott's fix what I used on Grant's hub...
  4. J

    Alternative to firewall insulation

    I used the replacement insulation plus the full coverage noise insulation. Carpet went on top of that. Heat and noise are minimal inside the cab. Water would be a huge problem under the insulation. It has to be stopped at the firewall. The black plastic needs trimming to fit around the column...
  5. J

    Steering cancel Cam

    If the wheel ever was equipped with a cancelling cam or pin, I see no evidence of it. Do you have the original? Is there room and correct diameter on the hub to install the OE cancelling cam?
  6. J

    Steering cancel Cam

    If the wheel ever was equipped with a cancelling cam or pin, I see no evidence of it. Do you have the original? Is there room and correct diameter on the hub to install the OE cancelling cam? When buying some shiny bling, it may be a good idea to check the fit and function first.
  7. J

    Air Intake and Carb Options

    I don't know what you mean by an upgrade manifold. A clarification would be helpful. The OE carb is a 2150 with 1.08" venturis. There's no real upgrade for that. The intake can be improved with a '72 and earlier that has no EGR crap. At least that is if your state doesn't have emissions...
  8. J

    Generating lackluster power out of my 77 302

    I had a '68 with a 289 that performed far better than the '77 302. Both where stock and I went looking for the reasons. I found the ignition and cam timing explained most of the difference. The rest was EGR. All this can be done without doing irreversible modifications that the emissions...
  9. J

    77 Help

    Parts replacement is the worst diagnostic technique known. A differential shop that sees this kind of thing daily would likely know quickly if the axle is turning. Another consideration is a dry slip joint in the drive shaft. They bind and release making a bang noise.
  10. J

    Generating lackluster power out of my 77 302

    The Reincarnation instructions are an abbreviated rehash of the Foureyedpride article I referenced in post#7. IE no new info. I use a Sun distributor machine on mine but a dial back timing light can produce the same results. The '77 specs for initial timing and curve were not designed for...
  11. J

    Rattling Tire Carrier Latch

    The rubber "snubbers" are visible in the first 2 photos above. There were never any others. The stainless wrap on the bar looks good so wear in the latch is likely the cause of the rattle. Bump the spare while latched to see what's loose.
  12. J

    Rattling Tire Carrier Latch

    The huge bumper pad on the lower tail gate, is some PO's attempt to control the twist of the frame caused by the cantilevered weight of the spare. A good goal but poor execution. The weight bears on sheet metal where it's likely to make a dent like the one below the R. The rear bumper would be...
  13. J

    Generating lackluster power out of my 77 302

    You can save money and get more grunt by installing a straight up or 4 degree advanced crank sprocket. The OE '77 sprockets had a 4 degree retard sprocket. First, do a proper ignition timing curve. Here;http://vb.foureyedpride.com/showthread.php?22229-The-Ultimate-Duraspark-Distributor-Timing-Guide.
  14. J

    Windshield to window frame gap?

    The only way to fill that gap is some kind of weather strip. Read this;https://classicbroncos.com/forums/showthread.php?t=305785.
  15. J

    Rattling Tire Carrier Latch

    Effectively, all the latch and tail gate soft parts need replacement. Unfortunately the EB vendors don't show much interest in facilitating the restoration of the stock swing away spare tire carriers. Sad. Instead they make their own, vary different systems. Many don't use the OE bumper.
  16. J

    USB charger wiring

    Here's a good thread by electronic nerds that quantifies the effect on a car battery;https://www.bigmessowires.com/2016/01/28/standby-current-of-a-usb-car-charger/.
  17. J

    Horse shoe shaped spacer under coils above retainer.

    Sounds like a Rube Goldberg repair for something that wasn't broken.
  18. J

    rear seat bracket

    It sounds like Frankenbronco is an apt description. I don't know of any vehicle that has the seats mounted to the frame. Maybe that's an indication it's a bad idea. It also sounds like you need a real shop manual to learn how your truck was designed.
  19. J

    Tucson Owners

    You have to love the shot at Gates Pass. I could see a wall size mural blow up for a proper EB man cave.
  20. J

    Prop valve adapter. Why can't the simple things not be easy?

    Hydraulic hose repair shops have the fittings you need. Ocala has at least 2.
Top