• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Engine angle

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Did you take pics? D

Not very many. I installed my 408C/T-18/NP205 drive train back in '03 and the only pics I took of it were after it was set. during the processs, I had the rear of the assembly hung on my overhead crane and played around with the tradeoffs between front and rear driveline angles (and the side mount details for the 205..another PITA)

Wish I had taken a little more off the rear and bound the front up a little more..in hindsight..because I had to deal with head-to-firewall interference.:-X

When Bax started a similar build, I passed on my data and he adjusted his accordingly. AFAIK he did not have to massage the firewall at all.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
The motor mounts are a fixed mounting point. The only variable (in this swap anyway) is the height of the transfer case. Find someone who still has a stock drivetrain and ask them to put a straight edge across the bottom of the frame rail and measure to the center of the rear transfer case output. That will be fairly constant regardless of any transmission or transfer case used.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I have some pics that may be helpful, but they aren't orthographic.

This one makes me think the engine mounts are almost perfectly aligned thru the crankshaft:



This one makes me think the t-case front output drop is about 5" below the input (which we know is aligned with the crankshaft):



This one says the t-case front u-joint is exactly as far back as the Xmbr centerline (trans mount bolts):



I didn't have a Xmbr or axles to measure against it, but here are all my frame dimensions:



So starting from the engine mount center, I think a stock eB would have 35" horizontally to the t-case front u-joint, and (assuming previous posters are correct about the engine being level at normal ride height) 5" vertical drop. There are the 2 upper vertices of the triangle. I don't know that I could even guess about the front diff u-joint's relative position, but it's horizontally rearward of the eng.mt. by approximately (the ring gear radius plus the pinion gear's length from the teeth to the threaded end plus about an inch). That's because the V8 engine perch is nearly perfectly aligned between the spring towers, and the springs are nearly perfectly (vertically) aligned above the center of the axle tube. I have no way of gauging the stock height since I've never worked on one, but that would be the minimum vertical drop for the 3rd vertex, and you could test several other calculated positions with more drop to check for various lift heights (if you have time & inclination).


This isn't proof of anything, but here's the best shot I have of the '75. I just can't see how anyone would think that raising the t-case would improve the d'shaft angle MORESO than lowering it would.

 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Nope not a believer. Steve is stuck on the drawing angles and I'm making driveshafts work. I think we can agree that if you drew a straight line and called it the center line it would start at the crank and end at the transfer case output shaft. Straight line but not level. say the engine was 5 degrees down in the back. This makes the centerline 5 degrees down from beginning to end. this works great for the rear shaft because the output is down 5 degrees. But my front output is pointing up 5 degrees. This is bad for my front shaft. Bad because I have a larger problem with u joint bind due to the 5 degree up angle. Now I don't care how you draw it, all I know is if I can lift that centerline as close to level / zero degrees my front drive shaft will have less bind that it will when it was pointing up.
I'm not drawing a picture I working on a bronco. And I'm not believing Steve even though I understand what he is trying to say.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
VT_Don had a post in this thread and it's disappeared. He aluded to a factory shop manual giving this info. I just looked through my complete '73 manual set and couldn't find anything.

Don - if you're out there - send me a PM on where to find it.

Thanks,
Todd Z.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Should be in the driveshaft section under the double cardon type. Last page.
bronco engine angle is 4 3/4 degrees. They list all the driveshaft and pinion angles as well but thats for stock height.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I'm not drawing a picture I working on a bronco.
OK Good luck with that. But do you mind if some of us blunder on with the discussion?


Another explanation occurred to me:
1) the t-case front output axis is parallel to the crankshaft/trans/t-case input line and (roughly) 5" below it
2) the "ideal" front d'shaft angle (according to Ford) is 0.5-3° off the t-case front output axis
3) the "ideal" front pinion angle (irrespective of the rest of the axle/steering) is 0.5-3° off the d'shaft

So the best driveshaft angle would be achieved when the t-case front output axis misses intersecting the front axle centerline by ~0.5°, and the diff housing (only - not the steering knuckles) has been rotated to match. That would happen when the crankshaft axis passes 5" above the axle (which would mean the t-case is drooped nearly vertical and the bellhousing is resting against the axle). Of course that's not possible, but it's useful to note.

Conversely, the worst d'shaft angle (for any given ride height) would be when the crankshaft (and front output) is perpendicular to the line from the engine mounts' axis (the pivot point) to the axle centerline. Since the axle is behind the mounts, that would mean the engine would be tilted DOWN in the front (opposite of what it really is) and the t-case high inside the cab (above the floor).

That part may be hard for some people to follow, but I'm sure an injuneer will have no problem with plane geometry. ;)

Of course, the "normal" engine angle (whatever it may be) falls somewhere between those extremes. But the issue is: CHANGING that angle. So obviously, any change that moves from a medium position toward the worst (raising the t-case) is worse than a change that moves toward the best. Right?
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Should be in the driveshaft section under the double cardon type. Last page.
bronco engine angle is 4 3/4 degrees. They list all the driveshaft and pinion angles as well but thats for stock height.

Thanks Jody - I found the double cardon driveshaft section for the EB but unfortunately no angular data in my '73 shop manual. They do list some angles for the large tandem axle trucks but that's all I could find.

No pun intended, but folks are getting too wrapped around the axle on this stuff. Stock is 4 3/4 deg. per you and I measured 5 deg. approx on mine at one point or another. This injuneer says that's fine for me :).

Todd Z.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
There was a chart in my 76 manual for the bronco I havent checked the 73 manual. I think folks are not looking at the whole picture. One is playing with driveshaft angle the other is making sure they dont get driveshaft bind due to a bad angle. Two different things while somewhat related. There are happy mediums both ways its give and take no matter which way you go.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
But the issue is: CHANGING that angle. So obviously, any change that moves from a medium position toward the worst (raising the t-case) is worse than a change that moves toward the best. Right?

Agree..sorta. But it really depends on what you define as "worse"; Bax and I are both talking about our shoehorning in a 408C with a 205 hanging off the end of the tranny. He raised his t-case more than I did and didn't have to modify a section of the dr. side firewall; I did.:(

On the other hand...I would have needed another 1" of body lift to raise my t-case any more.....and around and around we go.;D

I played the same game with the flathead V-8 EB project; except backwards. That one used all stock tranny/t-case and rear mount and it was the front mounting height I played around with. And after I was all done and have the body back on...I wish I had mounted the front of the engine lower. Argh.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Raising or lowering the transfer case has minimal change on the CV angle for the front driveshaft. Think of the angle of crankshaft centerline to front driveshaft like this >
The motor mounts and diff yoke are pretty much fixed (as the tips of >),
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Agree..sorta. But it really depends on what you define as "worse"...
I thought had defined it in my previous post, and I see what you're saying: your special circumstances might not be the same as the original poster's. But what I've been explaining is my response in post #6 to bax's statement in post #2 that raising the t-case improves the front d'shaft angle; not about engine-to-firewall interference.

So to clarify again: raising the t-case makes BOTH shafts' angles worse, and the diagram below shows why lowering it makes the front shaft's angle better.
Yeah, it's crappy because I just whipped it together in MSPaint, but the results will be the same if someone spends the time to draw it correctly in CAD.
The front axle tube in the diagram is always at the same relative location to the engine mount axis (red center point). The pink doublehead arrow is the offset, and longer is worse.

http://www.supermotors.net/registry/media/1011101
engang.gif


The rear shaft isn't as critical because it has a DC at the t-case, which does 2 things: 1) it doubles the acceptable working angle at that location (making t-case height/engine angle virtually irrelevant), and 2) it allows the rear pinion to point directly at the t-case instead of being parallel to the powertrain's axis.
 
Last edited:

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Also various text books on chassis fabrication detailing need for driveline angle and pinion angle to be parallel. .

For driveshafts that have a single u-joint at each end (like one of my fullsize pickups, for example). But what has that to do with an EB driveline??:?
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I thought had defined it in my previous post, and I see what you're saying: your special circumstances might not be the same as the original poster's. But what I've been explaining is my response in post #6 to bax's statement in post #2 that raising the t-case improves the front d'shaft angle; not about engine-to-firewall interference.

So to clarify again: raising the t-case makes BOTH shafts' angles worse, and the diagram below shows why lowering it makes the front shaft's angle better.
Yeah, it's crappy because I just whipped it together in MSPaint, but the results will be the same if someone spends the time to draw it correctly in CAD.
The front axle tube in the diagram is always at the same relative location to the engine mount axis (red center point). The pink doublehead arrow is the offset, and longer is worse.

engang.gif


The rear shaft isn't as critical because it has a DC at the t-case, which does 2 things: 1) it doubles the acceptable working angle at that location (making t-case height/engine angle virtually irrelevant), and 2) it allows the rear pinion to point directly at the t-case instead of being parallel to the powertrain's axis.

Your diagram isn't showing up for me, Steve.
 

driveshafter

Sr. Member
Joined
Jan 11, 2014
Messages
432
Loc.
phoenix az
driveshafts

the nrear pinion angle is supost to be neg 1 to 3 degrees from driveshaft the transfer case side has cv to relieve angle issues with lifted trucks you can use change over ujoints 0134 with a 1330 h yolk 1310 to 1330 it givs more angle without binding if you mill the ballstud and h yolk you can get a little more pm me with tech questions i dont know everything but ive got 20yrs under my belt
 
Top