• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

302 Clevor question

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I'm tired of searching. There is NOTHING on even the universe's internet (outernet???) about this idea. How come no one has ever discussed this in public on the internet???

Use a flat top Cleveland piston in a 302 with 2v heads to get 9.3-9.5 compression ratio...

KB177 pistons are relatively affordable and heads are plentiful. Even the later 4v heads have the huge chambers if a man wanted to go that way.

Here's the math: 1.5" half stroke + 5.090" rod + 1.67 Compression height = .054 above deck. with .041 compressed HG that's .013 into the chamber with at least another .050, maybe .075 to go before interference with the head.

My compression figures are based off a 78cc chamber, but those heads may actually be 74. I can't remember and I don't have the equipment to measure.

What say you?

(I'm working on a sentimental resto project that requires this engine to be historically accurate. doesn't have to make big power, but I need it to wear the original 180 degree headers that were on the original Boss 302.)
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I say if the math works do it - even decking it to get it closer. I considered this years ago for a Mustang I even bought a 2V Cleveland out of a Torino. The 2V Cleveland heads are really nice but I am not sure you can buy the adapter intake manifold any longer. It had a funny name but only one company was offering it. The '68 tunnel port was built on the Windsor block too so you have some options.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Normally I would just say to give up and use modern heads. But since you have a special desire to build it this way, making a Boss 302 clone, you are going to have to build it this way. But I would not say the heads are plentiful, most are 351M heads. But maybe you are in a lucky area that has them.

.054 above deck height is huge. Not what I would call a good plan. That starts pushing the top ring really close to the top of the bore. The top of the bore has a chamfer to it so the rings will go into the bore, its small but there. Depending on who chamfered it you might be getting into that.

The 351C heads I remember they tended to change almost yearly. I don't have my book in front of me for which one is which. But I would be looking really hard at a closed chamber head. Good quench. But open chamber heads on the street just suck.

What heads have you found so far? I'm thinking regular 302 flat top pistons would be a better match for that engine. Maybe with a little shaving here and there.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I'm using modified heads which for all intents and purposes are the Cleveland 2v.

I went to summit the other day and had them pull the KB149 which is the same compression height but with a little dome and there appeared to be about .25 inch between the top ring and the "top" of the piston (where the CH is measured from.)

I'd use the 302 pistons, but the compression is about 7.8:1. What's the point of even putting spark plugs in at that point. It certainly won't sound good with the 180 degree headers on it.

There's definitely some claying to be done and maybe a little trimming to fit. I picked up a "stuck" 77' 302 that had been bored 60 over the other day for $15. A few minutes with some PB blaster and a few bumps on a breakover and it was free. So now I get to strip it down to see about the chamfer and get a better look at the bore.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I'm not buying heads for this project.

I just want someone to check my math and tell me if I'm missing something. 9.3:1 compression is great as far as i'm concerned.

This engine may get as many as 1000 miles of parades in its life and a few laps around a few dirt tracks just to show the old car off to people who never saw dirt track racing in the 70's.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
As far as .054 being a lot of popout, its only .013 into the chamber when considering the gasket.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I can't find a good image of the 351M chamber. I don't know if they are truly open chamber heads or if any of the head is flush with the deck in the chamber area. That is the big mystery for me.

normally you leave the thickness of the headgasket to give quench height between the piston and the head. Pushing the piston out of the head gets scary. And going above the top of the head gasket puts it in the same space that the head goes. So every spec of the chamber needs to clear the piston all the way up to the outer edges. Even open chamber heads tend to come down to the deck height at the outer edges of the chamber. I don't see how the piston is going to clear the outer edges of the chamber in the head.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I tried to pick a few that have shading to illustrate the depth of the chamber on the shallow side. Even at only .013 coming above the head surface, there should be plenty clearance. We’re talking about a little more than the thickness of a dollar bill.

0903dccb4aebfe1497b4fa962d953d05.jpg


66cc9ab90044617566537d3c5e3b07de.jpg


4512505394d63da938dac308d29f4075.jpg


cfd9a5f052659a269e697ac3140b3524.jpg


I guess I’ll have to order some pistons and see what happens in a mock up. And hope I can return them if it’s not going to work. I’ve already got the HGs for a B2, so I don’t want to buy more, much less the expensive thicker ones.


Sent from my iPhone using Tapatalk
 

Nevadasmith

Full Member
Joined
Apr 30, 2016
Messages
182
Loc.
Fallon, Nv
Wallace racing has a good free online compression ratio calculator, there are many others..... I personally use vertual Dyno from the play store it has good calculators!!! As long as the top Ring is still .020 or more down the hole I think you will be fine..... Tho be warned the combination chamber design of that head can induce pinging at a lower compression ratio than you might think..... 9.3 is probably safe with a "boss" cam or after market cam....... I got a free set of 1970 "m" heads and did all the research to build a 351 cleavor.... But dropped the project because of combustion chamber design.......if you got the domed Pistons and you didn't have enough clearance you might be able to have some milled in a few places?? Good luck!
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I can't find a good image of the 351M chamber. I don't know if they are truly open chamber heads or if any of the head is flush with the deck in the chamber area. That is the big mystery for me.

They are completely open..no quench area at all.

I've got plenty of them lying around and could easily use a piston to test how far inside the chamber one will go before hitting.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
They are completely open..no quench area at all.

I've got plenty of them lying around and could easily use a piston to test how far inside the chamber one will go before hitting.

I was thinking this too. Plus the W block does not have the valve relief in the edge of the cylinder so pushing the piston out of the top of the block is possible. To a point.
I guess.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
This is going to sound crazy but as people have pointed out you are getting close to contact. As the engine revs your piston / rod combination is going to stretch a bit so leave some room. Depending on your cam your piston valve reliefs may not be in the right place so things may hit there too.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
There is info out there. Just not a lot and understandably so. The clevor was hot before the internet was and even when it was hot it was still not a everyday thing..
I'm not sure on your combo but it may work. Although I think that when 302boss pistons are used most people also go with 302 boss or the more plentiful 289 rods not sure if they are required or not but I think they were getting about 9.5-1 with them and 76cc heads.
If you can work it all out it would be a good project. Sounds like sentiment is winning out and I don't blame you in that department. although I would consider building the engine on the wilder side since its more of a show piece than a driver.
On the flip side if you cant swing the correct stuff for a clevor then you might consider getting a set of 180 degree headers for a standard 302 they are fairly cheap $300ish. compared to building a complete clevor.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I just realized this morning that I have some 289 rods with the longer length that I can use to get close to the same height these Cleveland pistons would put me at. And I might even get away with just swapping out rods and making my own flycutter to notch the stock pistons enough (hopefully "enough" won't be too much). I'll have to see how much lift the cam in this engine has...I was told its not stock, but it IS a Windsor cam. I'll see if I can find some markings on it.

So lots of playing to be done this weekend.
 

djhudson05

Sr. Member
Joined
Nov 29, 2008
Messages
542
In the late 80s,early 90s there was a company called B&A Performance thatspecialized in Clevors. I was going to build one for a 68Torino I had. If I remember right, they used 289 rods and not sure of the pistons. They also manufactured the special intake manifold you will need. I believe it was basically a Boss 302 manifold. Expensive if you find one. There are also some water jacket holes in the block to be plugged and new one drilled in the heads. I still have the info and template for the water jacket they sent me . If interested let me know and I will see if I can post pics or send info. Also B&A went out of business years ago.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I appreciate the offer. That information is scattered across the internet. They used 5.155 rods and Boss 302 pistons. I'd just like to find someone with experience trying to use the Cleveland piston with a 5.090 rod and open chamber heads.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
I'm not buying heads for this project.

I just want someone to check my math and tell me if I'm missing something. 9.3:1 compression is great as far as i'm concerned.

This engine may get as many as 1000 miles of parades in its life and a few laps around a few dirt tracks just to show the old car off to people who never saw dirt track racing in the 70's.

Always something ain't it brother.. Hang in there
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Will the 180° headers even fit the Bronco? What are they off of?
Hate to soo all this work just to find the reason for the work won't work.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
This particular engine will go in an old racecar . But if this piston idea works, I’m kind of thinking my little p heads on my explorer motor in the bronco may go away. in favor of some Cleveland’s.


Sent from my iPhone using Tapatalk
 
Top