• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Centech Wire Harness Newbie!

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
Ok so I will be digging in on this project next week and want to get my ducks in a row. I saved my previous harness just in case I need some odd ball connector. My big question is there anything other than the major tools, supplies i'll need other than tape, connectors, wire stripper/crimpers, solder to get this job done? One other question is there any method that works best for running all the wires? If any pitfalls or tips that could be shared would be great! thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You'll need specialty crimpers and such for the Weatherpack connectors that they include in the kit. Very nice and easy once you master the little differences.

What year is your Bronco? '66-'70 had the firewall connectors, but the Centech (like all the others too) is based more off of the '71-'77 wiring design. So be aware of the changes.

Map out where you want things to go first. Primarily regarding the passenger's side bundle/branch. Do you want your ignition wires running across the firewall, or coming out behind the engine? No functional difference, just aesthetics.
If behind the engine open the bundle loom and separate out the few you need and run them back behind the dash. Lot work, but can be worth it.
An alternate is to extend them slightly and run them all (alternator, sensor and ignition wires) down past the battery, over the alternator and up to the engine. This can also be very clean and functional, with less work.

Are you using a high power alternator? If so you do NOT use the Yellow alternator wire (same as your old Black w/yellow stripe) so you can pull it out of the harness too, and repurpose it for a heavy power load using a power stud in the location of your choice. Some put it back under the dash, but I think most of us mount it somewhere on the passenger side fender skirt for convenience.

If EFI, plan on where you will take power from. There are extra Green switched power wires on the passenger side you can use for various things. The White (I think?) ignition wire that runs from the "I" terminal on the starter relay to the ignition coil is no longer necessary for either EFI or even a full 12v ignition system. So that can be eliminated as well.

If a '70 or earlier, plan to relocate the fuse panel to the passenger side in either the glovebox (you can cut a hole in yours, or buy a new liner with a hole there already) or get fancy and mount it behind the ash tray or similar. But the old floor location near the driver's right foot and pedal are not that easy to achieve. I think they were intended to be able to, but I've heard it's awkward at best.

If you have a good sized dash-mounted radio, be aware that the bundle that runs under the radio is much larger than the factory bundle and might interfere. Figure that out ahead of time and you'll be happier. Whether it means massaging the bundle in heat to flatten it, moving the radio before you mount it, or re-routing it completely, now's the time to realize you have to keep an eye on where things fall.

Whether to do it with the dash out, or the dash in and you on your back is up to you personally. I've done it both ways and actually prefer with the dash mounted. But I can no longer bend and contort like I used to, so the next one may be with the dash out again.
The good thing is that it really lets you fiddle with it without getting light headed and blind. Also you won't fall asleep lying there under the dash on a nice warm summer day!
The best of all (though I have not tried it) might be to customize the harness to keep the dash connections separated by a connector(s) and mounting the harness bundle to the cowl area near where the defroster duct will be. Even if you don't customize the harness, you can leave the dash connections hanging loose and make them just prior to re-attaching the dash to the truck. Seen it done this way and it's very clean. Very out of character for the harness, and care must be taken to not set yourself up for being short somewhere, but super clean results.

You did the right thing by keeping the old harness. Some things like the Bake Warning Lamp socket are not reproduced, and the dash light bar connectors are not included with the kit for '73 and later Broncos.

If yours is a '70 or older, you will need to figure out the cleanest way to make two proper sized holes in the firewall for the grommets. The one where there is no hole is easy enough. But the one where there is already a small hole is more awkward. Jig some kind of a hole cutter up and you're good. But the setup can be a bear if you haven't done it before.

Lots more, but that might get you started.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
To expand on what JaxLax said, ADD YOUR OWN GROUNDS whenever you can.
Mounting your own stud to the firewall that extends through (just a bolt with washers) so you can mount the under-dash ground(s) as well as the new one you're going to make yourself under the hood, will keep things very happy in the cabin.
Then run a 10ga wire or one of the pre-made braided ground straps from that stud on the engine bay side to a bolt on the intake.

If yours does not already have one, create a ground directly from the battery to the body. The wheel well is where Ford put it, but the core support, wheel well, inner fender skirt, etc. will be good.

Main ground to engine of course, but adding one between the engine and the frame is just good practice.
At the instrument cluster, mounting the supplied (I think?) ground wire to the instrument voltage regulator mounting screw is a great location. Adding your own wire to ground the dash to the body (maybe that same stud on the firewall you added already?) makes the dash a happy place for electrons.

Pau
 

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
Stock up on good 3M electrical tape. You wouldn't think you would need it for a new harness but trust me, we used a crap load of it on my centech kit, for adding stuff, EFI, lights, stereo, winch etc. etc. ;D:cool::eek:%):D:cool:
 

JaxLax

Bronco Guru
Joined
Apr 22, 2002
Messages
3,310
Loc.
Jacksonville, FL
Stock up on good 3M electrical tape. You wouldn't think you would need it for a new harness but trust me, we used a crap load of it on my centech kit, for adding stuff, EFI, lights, stereo, winch etc. etc. ;D:cool::eek:%):D:cool:

I ended up basically doing two systems.
Did a Ron Francis for the Bronco hooked to the main battery, then an aux panel for lights/stereo/winch/etc to the secondary battery.

Just need a good alternator and an isolating circuit.
 
OP
OP
rydog1130

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
Awesome, thanks guys!

Paul, this is going on my 68 restomod, no efi, but I am running a stock auto column w/ a c4. I already replaced my switch and wiring in the column. Do you have any pictures of the extra grounding your talking about? I'm more of a visual person when it comes to these things. Im concerned on how I will plug the hole for the fuse box, will I have to make a plug or block off plate to seal that hole? I'm running a 60 Amp alternator which I don't think is that high, I vaguely remember when at the auto parts store they asked if I wanted a 55 or 60 I went with the 60 amp and for a radio I plan on using the retro sound radio I bought from jeffs.
 

Dlish

Sr. Member
Joined
Dec 6, 2011
Messages
552
I just finished up a Painless wiring swap.

As stated above, get the good 3M tape, it makes a difference.

And Harbor Freight has marine grade shrink wrap that has a glue inside of it, so it not only shrinks but also makes a truly water tight glued up bond too. Cheap and really good stuff. Add a heat gun if you don't have one.

Zip ties of various lengths

I set up a folding table next to the bronco and put the dash on it, and laid the harness on the dash, made a few connections that I could. Then a buddy and I laid it across the seats and fed the passenger and driver side wires through. Was able to get a lot laid out and loosely attached to dash.

After removing the steering wheel, I was able to get the dash on the column and about 8 inches from being in place, make some more connections, and keep feeding wires into the engine area.

Then finally get the dash back in place and connect the last couple (heater wire and knobs)

And good thing you kept the old, I actually scavenged a couple lengths of wire to add grounds as mentioned above.

Edit attaching picture, and from my phone so most likely sideways. But i used the center dash mounting hole that comes off the firewall as a place for a ground. Near the heater knob in the pic
 

Attachments

  • IMG_6229.jpg
    IMG_6229.jpg
    98.7 KB · Views: 111
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...Do you have any pictures of the extra grounding your talking about? I'm more of a visual person when it comes to these things.

Probably... But it'll be a chore finding them on this computer! But I'll give it a shot.
Maybe others have shots of what they've done too. What Dlish said about using existing holes is great. Plenty of them to go around on a Bronco usually.

Im concerned on how I will plug the hole for the fuse box, will I have to make a plug or block off plate to seal that hole?

Yes. Easy to do though. A small piece of aluminum trimmed to almost a square and screwed on over the two remaining rectangular holes left by the old plugs is pretty straightforward. You'll figure something out I'm sure.

I'm running a 60 Amp alternator which I don't think is that high...

Perfect. No changes to the harness then. Just run the large (10ga) Yellow wire clearly marked as the alternator BAT + or whatever it says, straight to the alternator's main output stud.
If your voltage regulator is over on the passenger side wheel well still, there will be the proper wires with a nice new connector right there for you to use.
If it's mounted to the firewall like many were after '73, you will likely have to open up the loom a bit and run the wires back to that point.

Not sure what they were thinking with the Purple "START" wire though. It's long enough for the automatic's neutral-safety switch, but is initially run all the way up the loom to the starter relay/solenoid corner.
Depending on where your switch is (on Broncos it's on the side of the trans), it's likely easier to pull it partially out of the harness, from the rear first, so you can run it out the firewall behind the engine, cut it to length, connect one end to the switch and the other end to the other side of the connector to run back out to the starter relay.

They have 2 Purple (actually called "Violet" in the GM color codes) wires. The short one is intended for manual trans trucks without the NSS and goes right to the relay's "S" post and works right out of the box.
The longer one is there too, but intended to be cut in the middle to connect to the NSS first. Up to you how to run it, but that mostly depends on where your NSS connector is now.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
A torch is my weapon of choice too so far. For heat shrink and solder.
I did recently get a heat gun for shrinking and softening, but have not spent any quality time with it yet. Interested to see how I like it compared to the torch.

Used to struggle with wimpy soldering irons. I guess they were wimpy anyway, and it wasn't just me! I've seen some amazing things done with irons, but the day I discovered that my little torch was so good, it was hard to put it down.

Paul
 
OP
OP
rydog1130

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
Yup, I picked up a torch the other day along w/ tape, heat shrink tubing etc. I think I'm good on supplies, Paul thanks for the info, my starter solenoid is mounted on the passenger wheel tub, so I think I'm good! a little nervous, but over all I don't think it'll be to crazy! Thanks guys!
 

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
I did a Centech several years back and was very happy with the results but the next time I do one I'll add several relays. I upgraded my heater blower and have dual wiper motors and those two items and the radio are on three individual fuses in the panel but are fed by one wire. I spent a LOT of time wiring, soldering, etc.. and was disappointed when I lost the heater, radio and wipers. Could not locate the problem so I had to pull my cage and dash. Even then it took a while to track down the problem but it came down to the wire feeding that circuit went all the way back to the key and ran through the plug on the back of the key. It shorted and melted. It was a really easy fix but hard to get to. It wasn't really centech's fault, I had more power draw due to the upgrades. Now the heater motor and wipers are on relays fused direct to the battery. Much better that way.
 
OP
OP
rydog1130

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
Good to know, right now I'm running the stock heater and vac wipes so I should be ok, but maybe upgrade those wires in case I upgrade!
 

JaxLax

Bronco Guru
Joined
Apr 22, 2002
Messages
3,310
Loc.
Jacksonville, FL
Good to know, right now I'm running the stock heater and vac wipes so I should be ok, but maybe upgrade those wires in case I upgrade!

This ended up being why I added the secondary fuse panel.
A relay off the ign hot and a battery connection installed NOW will give you (whatever size you want) the ability to expand/upgrade later to things that haven't even made it into market yet.

Whether it's aux lights, stereo, charging ports, or changing from vac/upgrading blower motors having that built in expand-ability will ease your mind.
 
OP
OP
rydog1130

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
This ended up being why I added the secondary fuse panel.
A relay off the ign hot and a battery connection installed NOW will give you (whatever size you want) the ability to expand/upgrade later to things that haven't even made it into market yet.

Whether it's aux lights, stereo, charging ports, or changing from vac/upgrading blower motors having that built in expand-ability will ease your mind.

I'm pretty new at this electrical stuff can you post up a link to the relay you bought? If you have a picture of it installed that would be great as well!
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
I recommend welding a galvanized 3/8" bolt to the frame and to the firewall by the battery to make your battery ground straps to.
 
Top