You'll need specialty crimpers and such for the Weatherpack connectors that they include in the kit. Very nice and easy once you master the little differences.
What year is your Bronco? '66-'70 had the firewall connectors, but the Centech (like all the others too) is based more off of the '71-'77 wiring design. So be aware of the changes.
Map out where you want things to go first. Primarily regarding the passenger's side bundle/branch. Do you want your ignition wires running across the firewall, or coming out behind the engine? No functional difference, just aesthetics.
If behind the engine open the bundle loom and separate out the few you need and run them back behind the dash. Lot work, but can be worth it.
An alternate is to extend them slightly and run them all (alternator, sensor and ignition wires) down past the battery, over the alternator and up to the engine. This can also be very clean and functional, with less work.
Are you using a high power alternator? If so you do NOT use the Yellow alternator wire (same as your old Black w/yellow stripe) so you can pull it out of the harness too, and repurpose it for a heavy power load using a power stud in the location of your choice. Some put it back under the dash, but I think most of us mount it somewhere on the passenger side fender skirt for convenience.
If EFI, plan on where you will take power from. There are extra Green switched power wires on the passenger side you can use for various things. The White (I think?) ignition wire that runs from the "I" terminal on the starter relay to the ignition coil is no longer necessary for either EFI or even a full 12v ignition system. So that can be eliminated as well.
If a '70 or earlier, plan to relocate the fuse panel to the passenger side in either the glovebox (you can cut a hole in yours, or buy a new liner with a hole there already) or get fancy and mount it behind the ash tray or similar. But the old floor location near the driver's right foot and pedal are not that easy to achieve. I think they were intended to be able to, but I've heard it's awkward at best.
If you have a good sized dash-mounted radio, be aware that the bundle that runs under the radio is much larger than the factory bundle and might interfere. Figure that out ahead of time and you'll be happier. Whether it means massaging the bundle in heat to flatten it, moving the radio before you mount it, or re-routing it completely, now's the time to realize you have to keep an eye on where things fall.
Whether to do it with the dash out, or the dash in and you on your back is up to you personally. I've done it both ways and actually prefer with the dash mounted. But I can no longer bend and contort like I used to, so the next one may be with the dash out again.
The good thing is that it really lets you fiddle with it without getting light headed and blind. Also you won't fall asleep lying there under the dash on a nice warm summer day!
The best of all (though I have not tried it) might be to customize the harness to keep the dash connections separated by a connector(s) and mounting the harness bundle to the cowl area near where the defroster duct will be. Even if you don't customize the harness, you can leave the dash connections hanging loose and make them just prior to re-attaching the dash to the truck. Seen it done this way and it's very clean. Very out of character for the harness, and care must be taken to not set yourself up for being short somewhere, but super clean results.
You did the right thing by keeping the old harness. Some things like the Bake Warning Lamp socket are not reproduced, and the dash light bar connectors are not included with the kit for '73 and later Broncos.
If yours is a '70 or older, you will need to figure out the cleanest way to make two proper sized holes in the firewall for the grommets. The one where there is no hole is easy enough. But the one where there is already a small hole is more awkward. Jig some kind of a hole cutter up and you're good. But the setup can be a bear if you haven't done it before.
Lots more, but that might get you started.
Paul