• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dual battery wiring

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
I haven't seen anything on this for a while. Looking for a simple wiring scheme for dual batteries. No winch or big stereo. Race rig with intent to run on one battery and one in reserve. Thanks in advance! Mark...Gaucho Mark's Racing #66.
 

snipes243

Bronco Guru
Joined
Oct 12, 2006
Messages
1,317
Loc.
Huntersville, NC
I'm planning on doing a genesis offroad " knock off " system.

https://www.genesisoffroad.com/universal-dual-battery-kit

Basically use the same cole hersee 48530 smart isolator.

Here's how it works.

When both your batteries are fully charged at 13.2 volts, they are automatically connected and are charged at the same time.
When you park and turn off the engine, but continue to use accessories such as lights or the stereo or a CB, both batteries begin to drain down.
When your main cranking battery reaches 12.7 volts, the smart isolator separates the batteries, so that your cranking battery will have enough power to start the engine. The second battery continues to power your accessories for as long as it will last.
After you crank the vehicle, your main cranking battery will be charged up to 13.2 volts first, and then the isolator will begin charging your accessory battery. By only charging one battery at a time, your alternator is protected from excessive strain.
What if your cranking battery is somehow drained down too low to be able to start the vehicle? We have a solution for that.

Press the Start Boost button and the isolator will connect both batteries together for 1 minute, acting like built-in jumper cables to jump start your engine off your accessory battery.
As long as the accessory battery has enough power, you'll be able to start your vehicle instead of being stranded with a dead battery!
The alternator will charge both batteries for 1 minute, then switches back over to automatic mode to reduce the strain on your alternator


https://www.amazon.com/Cole-Hersee-48530-Battery-Isolator/dp/B00LMGPHW2

https://www.littelfuse.com/products...attery-isolators/smart-battery-isolators.aspx

wiring diagram
https://www.littelfuse.com/~/media/...lfuse-if-161-48525-smart-battery-isolator.pdf
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
It's an interesting Engineering problem which has been solved numerous times in various ways.

I say it's an Engineering problem, because it is an exercise in compromise. There is no single best solution, and no one has come up with an clever solution.

The problem is that your reserve battery needs to recharge at a different rate than your primary battery. There is no work around for that. No combination of switches or diodes changes the fact that you can have one battery that is fully charged, and one that is completely discharged...and you need to recharge them differently.

(Note that this is totally different than running a pair of batteries in parallel. My Cummins, and my PSD have two batteries that are wired in parallel. That just increases the current capacity...but both batteries are at the same voltage at all times.)

Most people just run a diode bridge that prevents battery A from discharging into battery B, and vice versa. So you can have a single alternator that charges both batteries and prevents battery B from draining battery A. But of course if battery B is at 10V, and battery A is at 13.2V...then the alternator can't actually charge battery A until battery B comes up to 13.2V.

The best technical fix is to install two alternators. This is typically done for Ambulance service and RV's. It works.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
It's an interesting Engineering problem which has been solved numerous times in various ways.

I say it's an Engineering problem, because it is an exercise in compromise. There is no single best solution, and no one has come up with an clever solution.

The problem is that your reserve battery needs to recharge at a different rate than your primary battery. There is no work around for that. No combination of switches or diodes changes the fact that you can have one battery that is fully charged, and one that is completely discharged...and you need to recharge them differently.

(Note that this is totally different than running a pair of batteries in parallel. My Cummins, and my PSD have two batteries that are wired in parallel. That just increases the current capacity...but both batteries are at the same voltage at all times.)

Most people just run a diode bridge that prevents battery A from discharging into battery B, and vice versa. So you can have a single alternator that charges both batteries and prevents battery B from draining battery A. But of course if battery B is at 10V, and battery A is at 13.2V...then the alternator can't actually charge battery A until battery B comes up to 13.2V.

The best technical fix is to install two alternators. This is typically done for Ambulance service and RV's. It works.

What he said, saves me a lot of typing.

Adding charging diodes isolates the batteries and allows one alternator, but adds another point of failure that can take everything out.

I vaguely remember some marine alternators that are dual output. That is a group that wants reliability and redundancy as well.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
What he said, saves me a lot of typing.

Adding charging diodes isolates the batteries and allows one alternator, but adds another point of failure that can take everything out.

I vaguely remember some marine alternators that are dual output. That is a group that wants reliability and redundancy as well.

I don't worry too much about the failure point at the isolator. You can pretty easily just tie all three wires together to get home. (or take a single jumper cable and connect the batteries.)

The dual alternator is an interesting idea. I assume that it allows for different field voltages to produce currents based on need. A dual field alternator with two outputs would be able to do that, but I imagine that they are kinda pricey. (basically two alternators in one package.) edit: please don't confuse the 70's MOPAR dual field alternator with an actual dual field alternator. The 70's Mopar dual field alternator just happens to have isolated field wires for a single field. So there are two wires on the back. It's just a shorthand way to describe the pre-1970 single wire from the post 1970 two wire. There's only one field coil in that alternator.

Most Dual alternator applications that I am familiar with in Marine comes from having dual engines with dual alternators and only one battery pack...

The other problem with some isolating switch schemes is that the dead battery will suck power from the full battery. So if you have a battery at 1V, and a battery at 12V...and you "jump yourself" then eventually both batteries will end up at 6V...and the car won't crank.
 
Last edited:

ArmyCOL

Sr. Member
Joined
Feb 7, 2007
Messages
410
May want to look at this kit.

http://www.wranglerpower.com/

Kit Number 100-300

FORD BRONCO, EARLY BRONCO, 1966-1977This auxiliary battery tray holds group 24, 34, Optima 34/78, Odyssey PC1200 or equivalent battery. The Wrangler NW auxiliary battery tray is located on the passenger side of the engine compartment opposite the stock battery.Auxiliary Battery Tray Kit (shown)
 

pbwcr

Sr. Member
Joined
Jul 11, 2007
Messages
652
Hey Mark, for all the race rigs and prerunner wiring we always use is dirt simple setup. A marine 4 position manual switch, mounted close to the driver. Been doing it that way for 20 years we have never had an issue. My favorite location is under the driver seat.
We never use relays or electronic dual battery setups. Reason NOT simple and way to many failure modes that racer hate. Do not over thing this setup - keep it simple.

Switch positions are 1, 2, both, off
 
OP
OP
M

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
Awesome replies. Thank you.
We’ve been using the marine 4 position switch the last couple of years but always seem to have one that dies. Just wondering if we had it wired correctly.
I have the ambulance dual alternator package on my 2001 7.3 SD chase truck and it’s been flawless with good batteries. No room for that in the Bronco though.
I plan a couple of Oddesey group 34 batteries. Have EFI and 4R70W so good electrical is essential.
Thanks again, Mark


Sent from my iPhone using Tapatalk Pro
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
I install a dual Battery setup with a Blue Sea Automatic Control Relay (ACR). Never had a battery go dead. Great system for a House Battery and an Aux Battery. Blue Sea is known for their Marine Use products. Very nice quality.

I got the idea to use the Blue Sea ACR from a Toyota install using a Dual Battery Set-up from Off Grid Engineering. Now I use them as a Blue Print. Their system also includes a Battery Tray that has the mount for the ACR.
 
OP
OP
M

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
I believe I have that on the shelf in the shop. Two components, a rotary switch and something else. I’ll check it or tomorrow.
Appreciate all the good advice.


Sent from my iPhone using Tapatalk Pro
 

1sicbronconut

Contributor
Bronco Guru
Joined
Dec 26, 2006
Messages
2,469
Hey Mark, for all the race rigs and prerunner wiring we always use is dirt simple setup. A marine 4 position manual switch, mounted close to the driver. Been doing it that way for 20 years we have never had an issue. My favorite location is under the driver seat.
We never use relays or electronic dual battery setups. Reason NOT simple and way to many failure modes that racer hate. Do not over thing this setup - keep it simple.

Switch positions are 1, 2, both, off

This!! I even have one in my buggy that has a key so I can lock it in the off position!
 
OP
OP
M

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
Looked up Off Grid Engineering. Not what I have on the shelf so I ordered that kit. Looks well done and straight forward.


Sent from my iPhone using Tapatalk Pro
 

tatersalad

Bronco Guru
Joined
Jan 17, 2009
Messages
1,067
Hey Mark, for all the race rigs and prerunner wiring we always use is dirt simple setup. A marine 4 position manual switch, mounted close to the driver. Been doing it that way for 20 years we have never had an issue. My favorite location is under the driver seat.
We never use relays or electronic dual battery setups. Reason NOT simple and way to many failure modes that racer hate. Do not over thing this setup - keep it simple.

Switch positions are 1, 2, both, off

What he said... works in every boat I've ever owned.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Recently saw a discussion about an Australian dual battery setup that was uber slick. Don't remember if it was here, or on another forum, but I remember thinking that finally someone made a system that, though not simple or inexpensive, took out the last of the negatives and allowed both batteries to charge at their own need.
I can't remember the name, but maybe it was Redarc? Or something else, and I know there are a couple of Australian companies at least using that type of tech.

I'd prefer a smaller package, but with what it does it was sure slick. Didn't dig into the Off Grid Engineering stuff yet.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Used the Wrangler relay setup on my '96 Chevy pickup. Saved my bacon a few times while on long trips and I'd leave the fridge on all night. Would usually drain the starting battery, but the secondary battery was there to "self-jump" it each time.
The real solution would have been to connect the fridge to the aux battery! But I never did, and this way I never had a real long-term dead aux battery to charge up either. So I did not have an overcharged main battery, if that's an issue with that type of system?

I would keep my eye on the switch and flip it back to isolated after a little bit so I didn't overcharge one battery or the other, but I could see where that would happen if you left it connected and charging both on a long drive.
But I only ever needed it as the jumper, and that worked slick.

Paul
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
Awesome replies. Thank you.
We’ve been using the marine 4 position switch the last couple of years but always seem to have one that dies. Just wondering if we had it wired correctly.

In order to charge both batteries in this setup, the switch must be in "both". Otherwise you are only starting/using/charging battery 1 or battery 2. Maybe even only charging 1 battery depending on where you run the charge wire to.

I've used the blue sea systems charge relay with good results. When the voltage is over 13v, it closes to charge both batteries. With the engine off, it opens, isolating the two batteries. Use the 4 position switch on #1 or #2 to start and run the engine, both will charge while the engine is running.

https://www.bluesea.com/products/7610/SI-ACR_Automatic_Charging_Relay_-_12_24V_DC_120A

Sent from my SM-G981U using Tapatalk
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
I use the blue Sea 7622 which is the higher 500Amp. You can get with a switch or not. Just ground and install the cables. The ACR does the rest for you.
 

pbwcr

Sr. Member
Joined
Jul 11, 2007
Messages
652
Folks using the marine 4 position switch and having an occasional dead battery should pay attention to using the "both position" more often and probably should look at the battery brand. For sure the issue will not be the switch.

My experience with electronic versions with relays and diodes has been a continuing issue with plenty of guys. Marketing seems to override science now days. Hard to sell simple systems when large profits are available with a complicated gadget.
 

Hazegray

Sr. Member
Joined
Aug 10, 2004
Messages
795
Interesting note is that my 2017 Duramax has dual alternators (factory option).
 
Top