• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Easy Drum to Disc Conversion Question

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
My info says that a 1971-1972 d44 will have a Bom #603218 stamped on the axle tube. It doesn't say where. Memory (15 yrs ago) says it was on the passenger side on the front near the pumpkin. My info also says 71-72 use different axles than the 73 and up.

According to my vin # I have a very late 72. It had the press in seals in the spindles. It also took different outer axles. I broke a u-joint and destroyed the outer axle and had to buy an outer axle and spindle. I did the same with the good side.

The Bom # for a 73 D44 is 603368
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Thank you. It looks like I do have a 71 D44. I was able to read 03218 on the tube as you descibed (6 did not show; have to look again). The main question is will the 77 D44 knuckles work on the 71?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yes. People here do it all the time.
I have an early D44 and fitted the full-size F150 knuckles without a hitch.
I used my original Bronco axle shafts and everything.

Paul
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Thanks. Just a little concerned when I heard the 71-72 axles were different. Do you know what makes them different than >73 years?
 

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
Thanks. Just a little concerned when I heard the 71-72 axles were different. Do you know what makes them different than >73 years?
In an 71-72 Bronco the seal in the end of the spindle closest to the engine uses a press in or hammer in seal like a 2 wheel drive truck.

http://www.rockauto.com/en/moreinfo.php?pk=254581&cc=1119934&jsn=492

I believe the boss on the outer axle is a different dia than the one on a bellows type seal on a 73 4wd Bronco. When I messed up my outer axle on my 72 I went to Curry Ent to purchase a new outer axle they told me I must not have a Bronco axle because all Broncos were the same and used the bellows type seal. I think the sales person meant that they don't make axles for the 2wd type seal any longer. They just make them for the 73 up.
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Thanks for the reply. Do you see any problem with me using the axles, spindles and hubs from the 77 D44 on the 71 drum D44? I am planning on going this route but as someone mentioned earlier, "measure twice and cut once". Am I going to have to take both D44's apart and check axle splines and length prior to ordering parts? Sorry to beat this one to death but I'm getting a mismatch vibe on this one.
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Another thought >> How about the axle seals? Will the 71 D44 accept the 77 axle seals?
 

Fastwest

Sr. Member
Joined
Feb 7, 2015
Messages
371
Tagged since I'm doing the same conversion. I tossed the 77 housing since it was damaged but kept the brake setup. Will be installing the parts on a 73 Dana 44.
 

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
Since I have upgraded my axles to the later ones and have Ford disc brakes now the late axles "should" work. My info gives no info on 71 dimensions, axles or housings. I start another thread and ask about 77 axles in the early housing and reference this thread.
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Fastwest you should be OK. See earlier replies. I have this 71 D44 that is different. I thought I had a 73 in my earlier posts and later the EB I bought is a 71.
AL
 
Top