• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EFI Project weekend...New update

OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
OK got it going....... running rough to tired to work any longer...had an injector leaking so had to tear it back apart rebuild the injector again...o-rings ripped?...new too...fixed now and will time it and let it run....tommorrow.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
Intake

I just spent about 3 hours over on EBAY ...Looked to me like one of the Eddlebrook intakes would have much more room ..and more dollars also..
 
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
M/C Clearance fixed

OK so I placed a washer behind the M/C. Grinding was taking awhile and the amount of clearanced gain was very small. This is the fix picture
 

Attachments

  • 100_1603.JPG
    100_1603.JPG
    38.8 KB · Views: 81
  • 100_1604.JPG
    100_1604.JPG
    64 KB · Views: 81
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
Almost there

OK last night I got to start but got late so couldn't fine tune
1. VSS Cluster Bleep
2. Just about wired up
3. fuel line mess...
last three different angles of it buttoned up

Still left
timing
BC throttle cable adjusting
And drive
 

Attachments

  • 100_1596.JPG
    100_1596.JPG
    86.1 KB · Views: 82
  • 100_1597.JPG
    100_1597.JPG
    88.5 KB · Views: 99
  • 100_1598.JPG
    100_1598.JPG
    94.4 KB · Views: 93
  • 100_1610.JPG
    100_1610.JPG
    80.6 KB · Views: 92
  • 100_1611.JPG
    100_1611.JPG
    85.1 KB · Views: 100
  • 100_1612.JPG
    100_1612.JPG
    94.2 KB · Views: 98
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
Still idles rough...so working out bugs...runs great at anything above idle..got to search the forum here to see what others have done
 

brewchief

Sr. Member
Joined
Feb 11, 2007
Messages
877
Did you cap all the vacuum ports? IIRC there is one between the upper and lower intakes for the power brake booster.
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
Set base idle , set tps for proper reading , timing .... hmm what else ?
How rough , how long has it idled ? The computer does learn , it takes a bit.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
relearn

I was going to ask if a ford computer has to go thru a relearn ..a while back at work we had one that took over 45 minutes of relearn time most of ours learn in about 5 stops..
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Here's a great web site with info about getting the idle corrected. All Parts excellent but Part 3 especially good about steps required for computer "relearning."

Once when my battery was disconnected for a long period, it wouldn't idle worth a darn. Followed the instructions under Part 3 on the web site below without adjusting the throttle body and it got the computer corrected. My computer needed to "relearn" was only problem. Letting it sit for half hour worked and it ran like a champ...

www.muscularmustangs.com/iac.php
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
Great link , I've seen that before ....it in my "favorites" now . Thanks
 
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
OK Running tested runs pretty good!!!!

OK Running tested runs pretty good!!!!...Lots of torque wow!!!!!

OK got the codes..the one that concerns me is ...91..Left O2 sensor.and 23 closed TPS sensor volts higher or lower than expected.......I have an exhaust leak and I have bent this o2 sensor in the process....ugh...I have Shorties coming..and the O2 sensor I'll get new....

Question 1...I have the cam/302 with the non-HO firing order and the computer is HO firing order...so the rough idle is expected...but its getting better...so will this set up cause the O2 sensor....code?

Question 2...TPS sensor volts higher or lower than expected...is this cause I raised the idle screw on throttle body?......to help Idle!....The KOEO test gave me that code and then I adjusted.....it then was not present...but with KOER test it was present again....Let me know what you think
 

Attachments

  • 100_1614.JPG
    100_1614.JPG
    65.7 KB · Views: 102
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
Here's a great web site with info about getting the idle corrected. All Parts excellent but Part 3 especially good about steps required for computer "relearning."

Once when my battery was disconnected for a long period, it wouldn't idle worth a darn. Followed the instructions under Part 3 on the web site below without adjusting the throttle body and it got the computer corrected. My computer needed to "relearn" was only problem. Letting it sit for half hour worked and it ran like a champ...

www.muscularmustangs.com/iac.php


Cool I'll be all over this site.. here in a second.......I messed with the throttle body screw...maybe I should have left it...lets see...thank you guys...This is why I became a contributer to this site...

More to follow
 
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
OK it good...I have plan for the codes...what else?

Should I have a whirring sound...is it the filter mass-air set up...whistling whirring?
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
Question 1...I have the cam/302 with the non-HO firing order and the computer is HO firing order...so the rough idle is expected...but its getting better...so will this set up cause the O2 sensor....code?

I have the same set up (non-HO) cam. I bumped my idle up a bit to smooth it out. It is not bad at all now. I did have it idling like a top fuel dragster for awhile :) , but it drove me insane at stop lights , always thought it was going to die , though it never did.
It should not cause the sensor code.

Q#2 : The tps probably needs adjusted , which you probably have done by now using the link posted earlier.
 
OP
OP
Broncoward

Broncoward

Full Member
Joined
Aug 30, 2003
Messages
259
Loc.
Rolesville
Q#2 : The tps probably needs adjusted , which you probably have done by now using the link posted earlier.[/QUOTE]


No sir I haven't got to it...ugh the wife had other plans...ok tommorrow...that's my first order of business when I get off.....I got it as a favorite....OK thanks....its running even better than before...I should have left the idle screw alone..that was my carb personality coming out....

How about the whirring sound coming from intake...if you lookat my setup do you believe this to be normal?
 

HoosierDaddy

Contributor
Bronco Guru
Joined
May 29, 2006
Messages
2,776
Wish mine was here to start and listen to , don't recall any odd sounds. Seems like you got a decent amount of mechanical ability , does it seem wrong ? Hard to give an answer without actually hearing it.

Off topic , hows the NV3550 working for you , been eyeballing that for awhile now , for what is going to be my mall crawler bronco.
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
I would say you'll be okay once you get the TPS voltage set.

Mine is also an early firing order cam and surprisingly mine has never had a rough idle problem. I went into this project with real concerns about not changing the cam but after talking with our local f.i. specialists I elected to
keep the old cam. Now almost two years later I cannot tell any difference in the idle vs. when it had a carb.

On setting the throttle body adjustment, no big deal as long as you followed the Part 3 instructions and set the idle at about 700-800 rpms.

Don't know about the whirring sound. You might want to check to see if something's dangling loose around the internal parts of the mass air sensor.
 
Top