• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Engine Guru opinions needed - Heads

Yellow75

Bronco Guru
Joined
May 23, 2001
Messages
1,237
Loc.
Sioux Falls, SD
A buddy of mine has a completely reworked set of '69 351 heads. Been polished and new guides etc.. Had them on his 67 mustang until he decided he wanted to go bigger.

I could probably get them for a couple hundred I'm guessing. Is it worth my time for the 302? My lower end only has about 35-40k on it max. (should really get that speedo fixed! :) I have a valve on the drivers side that likes to knock when it's cold and i'm guessing the lower end (crate motor) I have only has 8.5:1 compression. The '69 will bring up the compression a bit also right?

OR do I just save my pennies and get a set of World or Edelbrock heads?

Thanks!
 
Last edited:

BroncoMark

Bronco Guru
Joined
Dec 1, 2005
Messages
1,272
Loc.
Irvine CA
Get the 351 heads and set them aside. Save your pennies for a 351 short block instead. ;D 35-40K isn't a lot of miles, but for the amount of work involved, you could do a complete swap.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,553
Yes it's a bolt on deal. Also I would get the heads if they only cost 2 bills and are ready to go. 69 was a good year for cast iron.
 

bronco60-niner

Sr. Member
Joined
Jul 11, 2005
Messages
645
Loc.
leavenworth,ks
the 351 heads use 1/2 bolts instead of the 302's 7/16 so you 'll have to get head bolt reducer bushings. I'm not sure on deck thickness of the 351 heads so pushrod length may or may not be an issue as well. Also depending on which 351w heads they are, combustion chamber sizes could be alot larger as well which could reduce compression and power. Just some things to think about.
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
you will need custom made pushrods too. Those heads will do more justice to a 351W. I heard that late 80's 5.0 FI heads really wake up a carbureted 302.
 

wildbill

Old Bronco Guy
Joined
Jun 29, 2001
Messages
6,890
:p :p :p It would depend on what you want the motor to do. Just food for thought the bigger the valve's the less the torque at the lower RPM and the higher you need to rev to get into the HP. Big valves and a good cam you can get some bad HP up in the 6000 RPM range if this is what you are lookin for go for it good luck.:p :p :p Bill %) :cool: ;D
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
69 351W heads should not lose any compression on a 75 302 might gain a little there should be no deck height problems and other than the head bolt hole size there should be no other problems I beleive you could pick up about 20 hp from the swap keep in mind that it will probably be in the higher RPM range. But the valves in the 351 heads are not so big as to lose low rpm power so I wouldnt worry about that.
 

pblackb592

Jr. Member
Joined
Apr 25, 2007
Messages
83
I ran 351's on my old and gone 302 after a full rebuild. Arp makes 1/2 head bolts just for a 351/302 combo. I used those instead of the inserts. I dont know if it was the rebuild the big cam or the heads that i installed but that thing scooted pretty good. I have a fresh 302 in my 72 but it doesnt have the balls my 70 did . Check your 351 heads, they might have the bump on the exaust, if they do grind them down some. The guy who checked the heads for me at the machine shop and during the valve job took those off for me and says he heard thats good for some extra ponies. Good luck!
 

fordtrucks4ever

Bronco Guru
Joined
Oct 8, 2006
Messages
1,280
Loc.
DFW
The heads have locating sleeves, so the bolt thing is BS. The bigger holes dont make any difference. Thats whatwashers are for. And plenty of heads use them. Other than having a larger intake valve you are gaining nothing. Intake and exhaust tracts are basically the same. Late model E6 or E7 EFI heads, will do the same thing and are dime a dozen. Those heads have value for a numbers matching Mustang fanatic, thats about it. But then again, thats just my opinion.
 
Top