• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

factory recommended camber and caster

dougsride

Contributor
Full Member
Joined
Dec 19, 2013
Messages
239
what is the recommended amount of camber and also caster for early bronco or possibly what has worked best for you guys with lifts and using 35" inch tires. got my readings from alignment shop and want to see how close i am. thanks
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
First how does it drive, if it drives good I wouldn't do anything other than have them set the toe, I run bout 1/8" toe in, some run as much as 1/4". As for the caster I run bout +4* some run more if they cut an turn the yokes. The factory camber specs were on the high side because of bi- ply tires that came on these Broncos, that being said I run bout +.75* on driver an +.5 on Pass. These #'s can vary and are just some to start with but it really all depends on how the Bronco drives to start with. Maybe others will post some specs
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
Forgot to mention before doing anything make sure all bushings in front end an all tierod/ draglink ends are good. The rear leaf bushings will also have an effect on how it drives, so make sure all is good or you will be chasing your tale
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, you should post your numbers if you want an opinion(s). Are you happy with the handling?
After my last axle swap and 3 1/2 lift upgrade I set the toe in the driveway and drove it for a few years. The handling was OK, and the tire wear was even. After getting new BFGs because of dry rot cracking I figured I'd get the alignment numbers. A guy I've known for a long time put it on a modern John Bean alignment rack and here are my numbers in degrees:
Left caster 3.9 Right caster 3.4
Left camber 1.9 Right camber .8
the only easy adjustment is toe, and my drag link allows left and right independent adjustment. First numbers were:
Left toe .12 Right toe -.1
So I had virtually 0 toe. After getting the recommended toe setting in degrees from a member on this site, we adjusted the toe to:
Left toe in .15 Right toe in .15 degrees.
It's hard to tell if it handles any better, but it is still good for and old Bronco. I'm glad I got the numbers and I'm glad I got the toe dialed in, equally left and right sides.
The recommended numbers in my Chiltons Manual is:
Caster 2 3/4 to 4 1/4, preferred 3 1/2 positive.
Camber 1 to 2
Toe in 1/16 to 1/4 inch
Good luck
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Factory numbers are probably not correct for a modified vehicle. The toe spec is probably a good one to keep. Caster, I like a little more self centering. 4-5° is my choice. Camber I like less than stock. Todays wider tires need to sit more upright. But camber is the worst to try and change, The ball joint eccentric will also change the SAI (kingpin) angle while a spindle shim won't. So you need to check the SAI and see if both sides are even.

The more extreme measures sometimes needed to get caster and camber right. They involve bending the axle tubes to fix camber. Caster can be an issue with U-joint operating angle as well. You can only do so much with offset bushings, drop brackets, and bending radius arms. You can always get enough caster doing it this way, but you may go to the point the U-joint on the driveshaft will never work. So a cut and turn to the axle. Undo all the caster fixes so the U-joint angle is perfect. Cut the ends off the axle and weld them back on at the correct caster. Depending on exactly how straight you get these you can also alter the camber/SAI numbers at the same time.

How well do you want it to drive? How involved are you willing to get into this alignment?
 
Top