• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Faulty NP435 adapter

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I'm rebuilding a T shift D20. Background info is it was fine behind the original 3 speed trans. After the 435 was swapped in it developed a tendancy to pop out of rear high. Upon teardown it was obvious the rear shift fork had worn into the rear sliding gear about .070". Usually this happens when bungie cords are used or when the shifter interlock plate is mis-adjusted. The constant pressure on the shift rail pulls the fork into the gear. This looked more like a symptom of a temporary fix than the actual problem itself, although it will eventually make the problem worse. The splines on the input gear (where the sliding gear meshes in direct drive) also had a strange wear pattern. Probably because the sliding gear couldn't move forward enough.

Further cleanup revealed something odd with the 435 adapter. Looking down from the tcase end the 435 plate appeared to be off center. So I put the spud shaft together with a new bearing and set the adapter up to rotate on the spud shaft. Then I could clearly see the mis-alignment. With the holes being off center the spud and rear output shaft will not be aligned and I think that is the real problem. Here are a couple videos to illustrate the problem.

http://www.youtube.com/watch?v=JW8nK_L2j8I
http://www.youtube.com/watch?v=Uw0V-nbcAak

I'm going to replace the sliding gear, fork and input gear, finish the rebuild and recommend either a new adapter or having this one repaired. I don't see a problem with cutting the 435 plate off and having it welded back on, straight and centered.
 

Attachments

  • Bronco 011.jpg
    Bronco 011.jpg
    115.9 KB · Views: 56
  • Bronco 014.jpg
    Bronco 014.jpg
    66 KB · Views: 66
  • Bronco 017.jpg
    Bronco 017.jpg
    55.2 KB · Views: 63
  • Bronco 022.jpg
    Bronco 022.jpg
    92.8 KB · Views: 64

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
What adaptor is this?
AA? plate with an I6 housing? welded housings? something else?
 
OP
OP
Viperwolf1

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Looks like plate welded to 6 cyl adapter.
 

Attachments

  • Bronco 030.jpg
    Bronco 030.jpg
    86.2 KB · Views: 87
  • Bronco 031.jpg
    Bronco 031.jpg
    95.2 KB · Views: 69

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I think that is a plate welded to a cut down V8 adaptor. The plate and I6 adaptor are a bolt together combonation.
 

shamu

Lucky as the day is long.
Joined
Jun 18, 2009
Messages
5,290
Loc.
Sachse,Tx
Here is the correct I-6 intermediate housing. I will sell it.
 

Attachments

  • Viper 001.jpg
    Viper 001.jpg
    114.6 KB · Views: 93
OP
OP
Viperwolf1

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
A little update.

Adapter is at the machinist. Should be an easy fix.

Tcase is rebuilt and ready to go. I ended up replacing input and rear sliding gear, front bearing retainer (cracked on one ear), rear shift fork (someone modified it with a grinder), fork and all the bearings. It will be a very nice working D20 now.
 

Attachments

  • Bronco 034.jpg
    Bronco 034.jpg
    129.9 KB · Views: 65
  • Bronco 033.jpg
    Bronco 033.jpg
    103.8 KB · Views: 102
  • Bronco 035.jpg
    Bronco 035.jpg
    107.5 KB · Views: 64
  • Bronco 036.jpg
    Bronco 036.jpg
    91.3 KB · Views: 54
  • Bronco 037.jpg
    Bronco 037.jpg
    78.1 KB · Views: 54
  • Bronco 038.jpg
    Bronco 038.jpg
    66.8 KB · Views: 56
OP
OP
Viperwolf1

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
That's one of my April fools edition carbon fiber plates.;)
 
Top