• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

floor pan welding

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
I have the WH floorpans and im planning to butt weld where they mate up at the pedals just below the firewall (the angles portion) because I think it will look better than an overlap,
so how can I set the gap for the butt weld correctly, ive seen a few options like butt weld clamps, screw the pan down in the correct position, or even overlap and cut through both pieces for the right gap, anybody done this or have some input/ideas, id like right around 1/32 gap for good penetration with minimal blow through
I know most people will say to just overlap and be done with it, but id like to hear the options for butt welding
 

BRONCROB

Bronco Guru
Joined
Nov 24, 2010
Messages
1,613
Loc.
WISNER LA.
If you're welding with a mig I would probably just gap it the width of the wire.I would play with some scrap first though to get the feel for it.
 

BRONCROB

Bronco Guru
Joined
Nov 24, 2010
Messages
1,613
Loc.
WISNER LA.
Yeah .23 would be a little tight.If your gap gets a little wide you can always hold a piece of copper against the back to prevent blowthrough.Practice makes perfect:D
 

Bferrari

Sr. Member
Joined
Mar 6, 2013
Messages
857
The clamps work good, I have used them for various pieces on mine and they leave a weldable gap. I burned them in with a MIG and .023. If you were TIG welding you would want a tight seam. I ended up overlapping mine, but I overlapped it on the bottom side of the angle in hopes to make it look like a seemless piece.
 

Attachments

  • IMG_3964.jpg
    IMG_3964.jpg
    115.8 KB · Views: 207
  • IMG_3965.jpg
    IMG_3965.jpg
    108.3 KB · Views: 223
  • IMG_5224.jpg
    IMG_5224.jpg
    94.6 KB · Views: 258

Green '70

New Member
Joined
Jan 4, 2014
Messages
42
Loc.
Wylie, Tx
Flange them if you have a bead roller. This will give you the look you want and all the strength of the overlap, fill as needed to make a seamless look.
 

Germd

Full Member
Joined
Jun 16, 2014
Messages
343
You guys that are expert elders are freakin' artists!��. I would gladly trade somebody several hours of my expertise ��(sewing a complex laceration or fixing a broken bone) for several hours of expert welding.⌚️������
 

Whoaa

Bronco Guru
Joined
Sep 26, 2014
Messages
1,059
Butt welds made easy = backing plate. Copper.

Use a Copper backing plate on the backside of the weld. And the easiest way to "find" a flat piece of Copper for a backing plate is to make one, make several while you're doing it.
Grab several piece's of 1" Copper pipe (or whatever size you have handy) varying from 2" - 8" long, rip down the side in a straight line, pry apart, and then hammer flat. Now you have the BEST backing plate's in the world. You can form these Copper backing plates to fit any profile, and nothing sticks to it while welding.

Use the Copper backing plates for all of your butt welds. This greatly reduces/prevents blow-through's, greatly reduces splater, and leaves you with a reasonably clean weld on the other side. Now it only requires minimal grinder clean up, often times no filler bead required, only a final cap weld.

The major problem w/ ALL "lapped" type of panel welds is that you introduce a new place that can more easily rust in the future. Any/all types of lap joint, as the name implies, lays bare metal over bare metal. Over time moisture finds it way in there, fine particals find there way in there, and there is no way for this moisture/partical's to ever escape and there is no way to wash it out.
All/most of Bronco rust issues are a direct result of lap joints from the factory. Regardless if you use some type of modern seam sealer [which is really GOOD stuff], its hard to beat a direct metal weld w/o lapping over the steal.
 

Whoaa

Bronco Guru
Joined
Sep 26, 2014
Messages
1,059

I've seen these, nifty idea....^

However the handle will be in the way when you try to put it in a tough spot, plus the copper of this spoon appears to thick to easily form to any profile you want by easily bending the copper by hand. Using Copper plates, made from pipe, can easily be attached w/ a varitey of clamps on the back side -which often times you can't reach while using both hands while you're welding.
 
OP
OP
BigBlueBronco71

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
Thanks for the input guys, I like the backing plate idea because I wouldn't have to be as concerned with the gap, but will the backing plate allow for a strong full penetration weld? seems like it would stop it from burning through the other side enough
 

Whoaa

Bronco Guru
Joined
Sep 26, 2014
Messages
1,059
Thanks for the input guys, I like the backing plate idea because I wouldn't have to be as concerned with the gap, but will the backing plate allow for a strong full penetration weld? seems like it would stop it from burning through the other side enough

Of course the magic of all fabrication is in the fitting, the actual "welding" part is easy....if everything is fittted perfectly.

However in the real world, it's rare to have ever panel always fitted perfectly. Sometimes there is a gap larger than you like that you'll have to fill with weld....this is where the Copper backing plate comes in.

Instead of blowing through and making a huge mess, and/or trying to spot weld (which is really just another cold joint lap w/ poor penetration) tiny spots and then letting them cool and then rinse-n-repeat until the gap is filled. Now with the backing plate you can make some reasonably long weld's, and fill some minor imperfection gaps along the way.
When doing panels, of course I always stitch back towards myself w/ welds as long as I think I can make easily w/o warping/tweaking the thin metal, while maintaning control angle of the whip & feeder head.
And when back stitching you're always rolling a hot bead into the intial cold joint from the previous weld -which you clean up w/ a grinder before the next back stitch is applied, and this technique gives you a 100% water proof/gas proof, 100% sealed joint that is 100% metal with no air gaps.

Using backing plates specifically allows you 100% full penetration, its solid steel through & through, plus easy access to the weld on the other side of the panel where the backing plate was located. After you make the weld, remove the backing plate from the other-side, clean up as nessesary w/ a grinder & brush, then a simple cap weld to finish that side of the joint.
 
OP
OP
BigBlueBronco71

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
with the copper backing idea, how do you clamp or hold it to the backside, there seems to be no place since you only have access to one side, I considered a strong magnet to hold it up but would be concerned this would effect the arc characteristics
 

7.3diesel

New Member
Joined
Jan 10, 2014
Messages
14
I have the WH floorpans and im planning to butt weld where they mate up at the pedals just below the firewall (the angles portion) because I think it will look better than an overlap,
so how can I set the gap for the butt weld correctly, ive seen a few options like butt weld clamps, screw the pan down in the correct position, or even overlap and cut through both pieces for the right gap, anybody done this or have some input/ideas, id like right around 1/32 gap for good penetration with minimal blow through
I know most people will say to just overlap and be done with it, but id like to hear the options for butt welding

Butt welds are cleaner. Use panel clamps, stitch welding, and use a copper backing plate. Magnetic versions are available.

An example here http://www.eastwood.com/4-inch-magnetic-copper-welding-backer.html

Eta: Once you use copper backers you will wonder how/why in the world you ever did without them. They are that good/helpful.
 
Top