• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Found this on the internet.

lagbolt

Sr. Member
Joined
Jul 18, 2012
Messages
577

Attachments

  • 03094wd_10z+1972_Ford_Bronco+Engine_View.jpg
    03094wd_10z+1972_Ford_Bronco+Engine_View.jpg
    76.6 KB · Views: 351

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Probably has a body lift if you look at the pic of the frontend flex you can see a body lift puck in there
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If you look at the same pic as was mentioned it also appears the engine mounts have been modified so the engine has probably been lowered to provide the extra clearance needed.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If you look close there appears to be a flat piece of metal running from the frame to the motor. Which is not a stock motor mount so they must have lowered the mounts to help get the engine lower.
 

Attachments

  • 1972_Ford_Bronco+Under_Carriage.jpg
    1972_Ford_Bronco+Under_Carriage.jpg
    120.5 KB · Views: 190

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Even with a body lift I thought it was impossible

We try not to use the word "impossible" even with a truck EFI conversion.
But we typically recommend against it because it's still not a very desirable swap unless you're into really WORKING for it.

Paul
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
If you look close there appears to be a flat piece of metal running from the frame to the motor. Which is not a stock motor mount so they must have lowered the mounts to help get the engine lower.

Is it me or is that front crossmember part of a later-model one (F150?) replacing the original?
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
My front cross member looks just like it and its stock

It looked like the bottom was open..C-type like the 150 and FSB. But I zoomed in on it and that was just the shadows..the original steering damper bracket is still in place.

I have to wonder how he lowered the engine without modifying the front cross member..?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...I have to wonder how he lowered the engine without modifying the front cross member..?

Dunno. But maybe he didn't? While you're zooming in, compare the height of the starter to the frame rail to see if you think it's still in the stock location or lower.
And what about the bottom of the mount in relation to the frame? They look lower to me, but I didn't really study it closely.
Maybe they're just reinforcing plates.

Still, it's hard to imagine one of those uppers sitting that low in an engine compartment without some serious mods having taken place. Whether lowering the engine, raising the body, or chopping the manifold in half and installing it on a 5.0 instead of a 5.8 (hey, every inch counts, right? ;D) or some other nefarious means of alteration.
Then again, maybe it's simply the camera angles. And they just chopped a big hole in the hood. The hood that we can't see.

Paul
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I have seen it once. 3" of body lift. Another ½" of body shims in the front. Some obscure fiberglass hood that was really tall way far to the front. After all that there was still throttle rubbing the hood issues.

There are better ways to make it fit and make it run better.
 
Top