• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Front brake drum removal

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
On my 67 how do I go about removing the front brake drum. Looks like on later model;s you remove the spindle nuts and bearings. Is it the same for 67???
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
It's kind of a good way to go anyway. While checking/replacing the brakes you can also check, re-pack and readjust the wheel bearings as well.
A good practice since wheel bearings were to be re-packed probably every 25k to 45k miles anyway.
And with the number of PO's that did not know how to adjust them properly, it's always good to check their work if it's a newer purchase.

Paul
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
It's kind of a good way to go anyway. While checking/replacing the brakes you can also check, re-pack and readjust the wheel bearings as well.
A good practice since wheel bearings were to be re-packed probably every 25k to 45k miles anyway.
And with the number of PO's that did not know how to adjust them properly, it's always good to check their work if it's a newer purchase.

Paul

Thanks Paul, will do and I think that the bearings can be purchased at a NAPA?
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
While you are in there, pop the slave cylinders apart and check their condition.

I'm redoing the rear end on mine which gets minimal use and found some nasties hiding in there.
 

Attachments

  • IMG_4938.jpg
    IMG_4938.jpg
    63.4 KB · Views: 94
  • IMG_4939.jpg
    IMG_4939.jpg
    92.7 KB · Views: 90

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I think that the bearings can be purchased at a NAPA?

Absolutely. They are some of the most common tapered bearings ever sold and are common to most Dana axles of similar vintage prior to the use of unit-bearings.
Should be no problem finding them in stock still at most parts stores.

The seal too.

Paul
 

McLeod

Full Member
Joined
Jun 29, 2008
Messages
296
While you are in there, pop the slave cylinders apart and check their condition.

I'm redoing the rear end on mine which gets minimal use and found some nasties hiding in there.

I agree that this is a must do.
But, in the interest of proper terminology, these are historically known as wheel cylinders.:cool:
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
I was scratching my empty head as to where are the slave cylinders. Wheel cylinders , ah got it. Disc brakes, yea some one has front wheel to wheel disc setup on marketplace for 750, OBO May look into that for later
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,123
Loc.
Cuchara, CO
I guess it’s not PC to call them slave cylinders anymore?? LOL

Then we’re going to need a new name for “master” cylinder too. Don’t want to trigger anybody! ;D
 

Cooper

Full Member
Joined
May 7, 2006
Messages
309
Loc.
Northeast
I always brace myself for an explanation to the counter person at the parts store as to what it is I'm looking for anyway, but my closest auto parts place is an Autozone.
 

bludorbronc

Sr. Member
Joined
Apr 19, 2006
Messages
653
How to remove drum. Take hammer and pound out.studs and when studs are out take each stud and go to grinder and remove swedges on studs.when done drum will come off easily.next remove hub off spindle and pound or press studs then reinstall everything will come off easy.
 
Top