• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

fuel gauge problem

jax34

New Member
Joined
Apr 18, 2011
Messages
33
I have 1973 bronco, dual tanks with dash selector switch. When i turn the key on or start it up my fuel gauge will go aup a little bit past 1/4 mark and shake real fast then drop to empty, also temp gauge isnt moving. I have checked for grounds, new constant voltage regulator, LOST.....HELP
 

66Bronco

Sr. Member
Joined
Jul 31, 2001
Messages
853
Try replacing the Fuel tank gauge switch. The one that allows you to see the fuel level of each of the tanks. You might try bypassing it first to determine it that's the problem but the last few times I've had that problem it has been the switch.

-Terry
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
I am new broncos when you say bypass where do i connect the wire to
 

66Bronco

Sr. Member
Joined
Jul 31, 2001
Messages
853
Try removing the wires (note how the wires are connected) and then try touching one of the tank wires to the gauge wire. I don't remember exactly but I believe there are only 3 wires. One from the rear tank, one from the aux tank, and then the wire going to the gauge.

If you need more help I'll have to try to figure it out on my Bronco when I get home. Note that sometimes the gas gauge may work by just wiggling those connectors on that switch.


-Terry
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Does the oil pressure gauge work? If it does then the IVR and the related wiring that powers it is good. If not then that may be your issue (thinking bad IVR or power in/power out wires on the IVR are reversed which could cause what you describe).
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
Yes there is only three wires on the switch so i will try that, Thanks, will let u know out come
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
Yes the oil pressure gauge does work for now, thanks for the info, when u say IVR, is that what I call a contant voltage regulator, if it I just replaced that
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
I tried the wires on the switch and i am still having same problem, if i take the ground wire off the bezel and dont ground the ivr the fuel and temp gauge peg out, touched a probe to hot wire on sending unit and it flashes or pulses....i think i might try a bullet;D
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
Ok guys here is what I have done i have checked my gauge with a 9 volt and fuel, temp pegged out. Oil gauge works ok but i am not happy with it neither was my father. I took the sending unit wire and grounded and the gauge only went to 3/4 full so i am thinking my problem is a wiring defect somewhere. I guess i am going to run all new wire on the outside and see if i can get it to work, COULD THIS PROBLEM BE IN THE IGNITION SWITCH? Thanks in advance for any info, just bought this bronco for the wife and have very little knowledge of them
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
One more thing the jackwagon that owned this before has a ground wire from the instr bezel to the ivr instead of it bolted to the bezel itself, and then a ground from tue ivr to frame, does this matter
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I tried the wires on the switch and i am still having same problem, if i take the ground wire off the bezel and dont ground the ivr the fuel and temp gauge peg out, touched a probe to hot wire on sending unit and it flashes or pulses....i think i might try a bullet;D

This is all normal.

Ok guys here is what I have done i have checked my gauge with a 9 volt and fuel, temp pegged out. Oil gauge works ok but i am not happy with it neither was my father. I took the sending unit wire and grounded and the gauge only went to 3/4 full so i am thinking my problem is a wiring defect somewhere. I guess i am going to run all new wire on the outside and see if i can get it to work, COULD THIS PROBLEM BE IN THE IGNITION SWITCH? Thanks in advance for any info, just bought this bronco for the wife and have very little knowledge of them

Possibly a problem with the oil wire. You can ohm it from one end to the other. It should be less than .5 ohm. A problem with the ignition sw would affect all 3 gauges.
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
Just noticed something this morning, the guy before has wrapped the threads on temp send unit with teflon tape, could this be affecting my gauges by not getting a good ground, because temp gauge doesnt work either
 

66Bronco

Sr. Member
Joined
Jul 31, 2001
Messages
853
Just noticed something this morning, the guy before has wrapped the threads on temp send unit with teflon tape, could this be affecting my gauges by not getting a good ground, because temp gauge doesnt work either

Yes.


-Terry
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Just noticed something this morning, the guy before has wrapped the threads on temp send unit with teflon tape, could this be affecting my gauges by not getting a good ground, because temp gauge doesnt work either

Yes, that would be a problem. Teflon paste will allow metal to metal contact for ground where the tape will insulate.
 
OP
OP
J

jax34

New Member
Joined
Apr 18, 2011
Messages
33
Thanks guys will try this tonight, getting very frustrated with this
 
Top