• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

gas gauge help

usmcsmith

Jr. Member
Joined
Sep 6, 2009
Messages
115
Loc.
Newark
Mine just reads empty. I bought this vehicle last month like this.

What parts would I need to fix this? I have 2 tanks a 12 gallon and an 8 gallon I believe

Also if I am going to need 2 of certain things please include that also where I could pick them up would be great.
 

Jonboy69

Full Member
Joined
Jan 25, 2009
Messages
340
Mess with the switch & see if you can get the guage to move. Flip back 7 forth a couple of times. Mine acts up occasionally & it is somewhat common. If that does not do it, make sure all the connections are good going back to the senders from the switch.
 

oleguy74

Contributor
Bronco Guru
Joined
Mar 26, 2008
Messages
2,034
Loc.
calif city ca
fuel switch

remove sw and check wiring.remove orange wire from sw that goes to gauge.turn ign sw to acc moumentarily groung wire to see if gauge goes to full.if so gauge is ok.next trouble shoot tank wiring.also if oil and temp work ivr ok.don't leave ground on very long.just long enough to see if gauge goes to full.
 

Attachments

  • TANK SWITCH STOCK.jpg
    TANK SWITCH STOCK.jpg
    63.7 KB · Views: 109

bigbri69

Sr. Member
Joined
Oct 7, 2007
Messages
421
Loc.
tomsriver
remove sending unit.the brass ball that floats is bad.it fills with gas and cant float anymore.like a 4 dollar part.or being you have the sending unit out to check float you can just replace to hole sending unit.bolth my 76 highboy that had the tank behind the bench seat and my 69 bronco bolth had the same issue when i bought them.76 highboy i just changed the fkoat ball and the bronco i changed intire sending unit cause it dident look so good having lots of rust and no screen left to filter dirt.its about a half hour fix.good luck!
 

oleguy74

Contributor
Bronco Guru
Joined
Mar 26, 2008
Messages
2,034
Loc.
calif city ca
put an ohmmeter accross the terminals of each sender.if it reads around 70 ohms or more float may be bad.a reading of 10 ohms is full,73 ohms empty.
 

Wyldebill

Full Member
Joined
Feb 8, 2008
Messages
292
Loc.
Berthoud, Colorado
Before you do any thing else, grab a jumper wire and crawl under the Bronco. The with the ign switch on, and someone in the cab to read the gauge to you, run your jumper wire to the terminal on your sending unit going to the gauge. When you ground the other end of the jumper wire, the gauge should go to full. You will have to try the switch on the dash in both positions and you'll have to do this at the sending unit on both tanks. If the gauge goes to full, you know the gauge is good and you have to concentrate on the sender or the wiring.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
What parts would I need to fix this? I have 2 tanks a 12 gallon and an 8 gallon I believe

Also if I am going to need 2 of certain things please include that also where I could pick them up would be great.
The parts you would need to fix this kinda depends on what's wrong/broken/not working. That's where you come in!;)

The circuit for the fuel level starts at the Instrument Voltage Regulator (IVR). The IVR also powers the oil pressure and water temperature gauges. So... If the oil pressure and water temp gauges are working, chances are the IVR is OK. Power from the IVR goes through the fuel level gauge, and either to the main tank, or, in the case of factory installed dual tanks, it goes to the common of the fuel level selector switch on the dash. Be aware of whether you have the switch or not. I bought my Bronco with dual tanks, but one was obviously an aftermarket (or homemade) tank, and had no level sending unit, so I did not have the dash switch.

The tank level selector switch is double pole, double throw switch, but Ford only used one half of it. So, all it does is take the IVR power after it goes through the gauge, and send it to either the main tank sending unit or the side tank sending unit. You can check for IVR power at the sending unit(s) by hooking up a volt meter on the 20 volt DC scale, and check for a pulsing voltage. The output of the IVR is a pulsed voltage, pulsing about twice a second. Another test, at this point, is to ground the wire coming from the gauge directly to the frame. This should peg the fuel level past full.

The sending unit is just a variable resistor. It should have about 75 ohms resistance with an empty tank, and about 10 ohms resistance with a full tank. You can measure the resistance of the sending unit with our VOM/DVM. The sending unit should have a connector with two wires. One coming from the gauge, and the other is a short pigtail that should be attached to the frame. The frame is then part of the circuit to make the gauge work, and it is necessary for the frame to be grounded back to the battery. The fuel sending units are the only thing grounded to the frame from the factory, that I know of.

You should now have enough information to troubleshoot your fuel gauge.
 
OP
OP
U

usmcsmith

Jr. Member
Joined
Sep 6, 2009
Messages
115
Loc.
Newark
Well thanks everyone for the input I will have to start tweaking and taking notes this weekend
 
Top