• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gear selection

jk667201

New Member
Joined
Jul 17, 2012
Messages
43
Loc.
California
I need to pick out a gear ratio to stick in my axle housings. This is the planed set up, 4r70w, atlas 4 (unknown ratios), 37 or 38 tires.
If I go with 37" tires gears should be 5.13?
If I go with 38" tire gears should be 5.29?

The atlas is unknown because that would be my next question, I don't want to learn the hard way and wind up having to sell a very expensive TC because I picked the wrong ratio.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Truck or Mustang? If you drive both you will realize there is a difference.

It is hard to say. I have driven Coyote engines, but never with the 4R70W. Not sure how it will behave. The final drive numbers sound reasonable. Probably the 3.8 Atlas would be a good match.
 

TN1776

Bronco Guru
Joined
Oct 24, 2006
Messages
2,632
Take a look at your engine's power band, and then start plugging different gearing combinations into this tool:

http://www.grimmjeeper.com/gears.html

If you are going to be doing any slow, technical wheeling like rock crawling, 100:1 is a nice gear ratio in your lowest range. With the Atlas and an Automatic with overdrive you can get the best of both worlds - cruising on the highway at a reasonable RPM while still getting the low gearing for crawling, and a decent balance anywhere in between.

I have an NP435, D20, injected 351w and 4.11 axle gears. I'm just under 70:1 in my lowest range and cruise on the highway at 65mph at 2500 RPMs. Its okay but I'd like to get a little lower while preserving a reasonable cruising RPM. One day.
 
OP
OP
J

jk667201

New Member
Joined
Jul 17, 2012
Messages
43
Loc.
California
Take a look at your engine's power band, and then start plugging different gearing combinations into this tool:

http://www.grimmjeeper.com/gears.html

If you are going to be doing any slow, technical wheeling like rock crawling, 100:1 is a nice gear ratio in your lowest range. With the Atlas and an Automatic with overdrive you can get the best of both worlds - cruising on the highway at a reasonable RPM while still getting the low gearing for crawling, and a decent balance anywhere in between.

I have an NP435, D20, injected 351w and 4.11 axle gears. I'm just under 70:1 in my lowest range and cruise on the highway at 65mph at 2500 RPMs. Its okay but I'd like to get a little lower while preserving a reasonable cruising RPM. One day.

at what RPM should you be at to shoot for that 100:1?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The 100:1 crawl ratio he's referring to is not rpm dependent. It's strictly the multiplication of the transmission's first gear ratio, times the low-range ratio of the t-case, times the rear end ratio. Low x low x diff = crawl ratio.
With your automatic being a taller first gear than most truck-based manuals, but adding torque-multiplication to the equation, you probably don't need the full 100:1 that he likes.

Let's say you have 3.24 to 1 first, 3.8 tc, and 5.13 rear end, you've got a 63.16:1 crawl ratio.
I don't remember the first gear of your 4r70 though, so that number was just thrown out there for comparison purposes.

I would add the another question though. What is your expected driving scenario too? Are you indeed looking to take it to the Hammers, play in the dunes, run up the Rubicon or head to Arizona or Utah? Or is your expected driving going to include more weekend fun with the family heading to the beach, or daily driving along certain freeways?
If wheeling at all, will you be driving it there, or trailering it?

Since you can choose your T-case's low-range ratio, your rear end ratios should absolutely reflect a bias towards your street needs first. Then off-roading next.
Just my opinion anyway. Your setup doesn't really sound like a friendly daily-driver, so I'm guessing it's going to be biased more a a weekend fun rig, or a hard-core dirt player?

Paul
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
4R70W is 2.84 1st gear and .70 OD.

One thing that paper engineers overlook is the convertor multiplication. Typically they throw out the number of 2:1, which is a good ballpark number. What they are forgetting is you have to load the convertor to get that. You come up on a rock/ledge/tree/whatever obstacle and basically stop. You give it gas, it revs, loads the convertor, and you pop over the top too deep in the gas and go flying uncontrolled. Yes, you do have the ability to get double the reduction but it is uncontrolled. Using real gear to get crawl it will just idle into and over stuff. You can set the engine at pretty much a slightly faster then normal idle and the wheels will maintain rotation over everything at a slow controlled speed.

Another thing is engine braking. That 2:1 is out the window for engine braking as well. It is actually a multiplier the other way. Unless you can get some engine RPM you don't have engine braking through a torque convertor.
 
Top