• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

handles like a wet sock

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
When I drive it , it's like i'm constantly correcting it it's like I have to chase it all the time to keep it on the road.Everything is brand new in the front end. Everything turns freely when I had it on the plates yesterday. No drag whatsoever no binding axel, joints are a good shape. Well , brand new i sent all my specs to Toms yesterday. I have two options longer radius, arms or drop brackets for radius arms don't like what they look like.What are my other options
It has a 4 turn box stock Pitman it has a heim joint set up on it 7 deg c bushings everything is tight
camber left 1.3 right 0.6
cross camber left 2.1 right 1.6
caster left 2.1 right 1.6
thanks for your help
 

LUBr LuvR

Contributor
Bronco Guru
Joined
Dec 31, 2015
Messages
2,228
Front end pics

1000028584.jpeg
1000028583.jpeg
1000028582.jpeg
1000028596.jpeg
1000028580.jpeg
1000028579.jpeg
1000028578.jpeg
1000028577.jpeg
1000028576.jpeg
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
It needs more caster. That is the ultimate fix. The other issue is the drag link being significantly longer than the track bar, the angles look good but they do run in different arcs so there is some bump steer. With enough caster the bump steer probably will not be noticeable.

The other option is Duff’s T Rex arms. To add more caster. The perfect solution is to cut and turn the axle for more caster but it is way more involved.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
How much lift?
Why not use a dropped pitman arm AND trackbar bracket?

And just for giggles, do the steering test.
This is with a helper turning wheel back-and-forth while you watch what’s going on underneath.
Tires fully on the ground, helper racking the steering wheel back-and-forth about a half a turn in each direction.
One thing you’re looking for is any movement in the track bar.
Other than that, yes, you need more castor.

You are 100% certain that the C-bushings are in correctly?
 
OP
OP
D

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
How much lift?
Why not use a dropped pitman arm AND trackbar bracket?

And just for giggles, do the steering test.
This is with a helper turning wheel back-and-forth while you watch what’s going on underneath.
Tires fully on the ground, helper racking the steering wheel back-and-forth about a half a turn in each direction.
One thing you’re looking for is any movement in the track bar.
Other than that, yes, you need more castor.

You are 100% certain that the C-bushings are in correctly?
yes c bushing are in correctly no play at all ! no movement in track bar
 

serial car restorer

Yes, I'll restore almost anything...
Joined
Aug 27, 2024
Messages
742
Loc.
Western Oregon
I'm going to say not enough caster and tire pressure too high, both amplified by the bump steer from unequal track bar and drag link lengths. How much lift are you running?
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,781
so it shows the specs as a new generation bronco, that could mean lots of red right there.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
That track bar drop bracket. It looks like it is only bolted in. Generally (every time I have seen anyway) that is not enough. A tiny amount of play and it's all over the place.
 
OP
OP
D

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
How much lift?
Why not use a dropped pitman arm AND trackbar bracket?

And just for giggles, do the steering test.
This is with a helper turning wheel back-and-forth while you watch what’s going on underneath.
Tires fully on the ground, helper racking the steering wheel back-and-forth about a half a turn in each direction.
One thing you’re looking for is any movement in the track bar.
Other than that, yes, you need more castor.

You are 100% certain that the C-bushings are in correctly?
yes c bushing are in correctly no play at all ! no movement in track bar
I'm going to say not enough caster and tire pressure too high, both amplified by the bump steer from unequal track bar and drag link lengths. How much lift are you running?
3.5 lift
 

widowmaker77

Contributor
Sr. Member
Joined
Oct 11, 2007
Messages
564
yes c bushing are in correctly no play at all ! no movement in track bar

3.5 lift
I had 7* c bushings with like +1.5* of castor with a 3.5” lift. Could barely hold it on the road at 50mph. I ended up doing a cut and turn on my inner c’s and set them at +7* if I remember right. I went an extra step though and cut the wedges off and set my pinion angle (probably not necessary though) . Tacked everything up pulled frontend back out and welded it all up. I’m using 2* bushing now in mine. Drives way better! I’m also running front and rear sway bars. If you’re not concerned with front pinion angle, I’d go long arms with 7* bushings. Duffs arms have 4* built in, toms have 7* built into theirs.
 

bigmuddy

Contributor
Bronco Guru
Joined
Dec 28, 2004
Messages
8,071
Loc.
Marthasville Missouri
may not be an issue but what is up with the multi stacked washer between the drag link and the pitman arm? Bit unusual?

Try dropping your tires down to 25-27 and drive it.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
may not be an issue but what is up with the multi stacked washer between the drag link and the pitman arm? Bit unusual?

Try dropping your tires down to 25-27 and drive it.
Ben, those are safety washers made for that purpose, they are machined to that shape. It needs more caster.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Ben, those are safety washers made for that purpose, they are machined to that shape. It needs more caster.
Those don't looks like safety washers. Looks like regular washers stacked as a spacer. A safety washer should be under the heim.
There are also a stack of mis-alignment spacers that could be mistaken as well. Which could also lead to an issue if someone drilled the knuckles/pitman arm for standard 3/4" hiems and later went with the high misalignment spacers and now have to run too small of a bolt for the hose they drilled.

More caster would help, but only if there are no other issues.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
is a misalignment spacer for sure, got a better image, hard to tell without seeing parts in person. I make safety washers that have a lot of misalignment designed in them, it’s just hard to scale from the pictures.

Still stand on It needs more caster. There are other issues for sure, unequal length drag link and track bar for instance. But with proper shocks and caster it should drive well, beyond those things we are all in conjecture because we can’t put hands and eyes on the entire package other than everything is new, which from the condition in the pics we have no dispute, it does all look new.
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
1777857960130.png

Pitman arm, 6 washers, heim alignment spacer, heim.
If heim joint threads are 3/4-16, through bolt looks to be 5/8".

Cut and turn.
 
Last edited:

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
View attachment 961162
Pitman arm, 6 washers, heim alignment spacer, heim.
If heim joint threads are 3/4-16, through bolt looks to be 5/8".

Cut and turn.
Missed that in the pics, that is an issue. If the spacer is needed, it needs to be a solid spacer. What is there is fine for short term tuning but needs to be addressed as soon as tuning is confirmed. The bolt should also fit in the hole without being sloppy, as with the knuckles.

My apologies to the OP, we are picking at a few things that we don’t know for sure are an issue but worth bringing up.
 
Last edited:
Top