• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

handles like a wet sock

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
With the taper of OE TRE's there's no need to worry about any wiggle since tightening the nut pulls it all to zero clearance, but with SRE's the ONLY thing that keeps things from moving relative to each other is the torque on the thru-bolt. A tight fit is still a good idea. The bolt should be mic'd and then the holes reamed to maybe as much as .002" oversize. Make the holes exactly the same and it's a hammer fit that doesn't actually solve all of the problem. The bolt should be at least a Grade 8 and I'd suggest it be a "Grade 9" or an AN bolt torqued to max spec.

Missed that the spacer is stacked washers too, agree that needs to become one piece, and one of those washers be moved to below the SRE to become a Safety Washer.

Either the drag link needs to be shorter or the trac-bar needs to be longer. Parallel only works with same length. If they're going to be different lengths then I suggest laying out the arrangement on the shop floor and moving the end frame positions until the arcs of the travel of the axle mounted ends be nearly identical. Can use a string and sidewalk chalk for this. Focus on the range of 1" down travel to maybe as much as 3" of up travel. Outside of that region the arcs will be hopelessly going in different directions, but for highway driving that range is where it'll mostly be operating.
 

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
I also find the washer stack unusual, i have never seen anything like that on steering components. I have less lift than you my goal is 3.5 caster using 7* bushings, and stock arms. My wondering doesn't seem as bad as yours i can drive at hwy speeds ok.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I'm guessing the stack of washers was to dial in bump steer correction.

While we have been looking at the front axle, don't forget the rear can cause massive stability issues as well. If it is moving around (bad bushings is common) it will bake it impossible to drive straight. a tiny shift to the rear will steer the bronco and you will be putting a lot of steering input to chase it. I'm talking so little movement you don't see/feel the back moving around and will forever chase the front end thinking that is the problem.
 

Qumanchew

Contributor
Full Member
Joined
May 16, 2018
Messages
317
Loc.
Kutztown PA
Along with removing the washers on the pit man arm I would also remove the misalignment spacers on the tie rod. No need for them on the tie rod as it will only see a very small amount of misalignment when you turn. The closer you can keep the heim to the knuckle the better. This cuts down the amount of force/ stress being applied to the through bolt.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
But as a book end to your comment, more caster does increase the angular change that the steering arms/knuckles go through.
Sometimes necessitating some sort of spacer on the tie rod.
But that’s when you get to that more caster point!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Along with removing the washers on the pit man arm I would also remove the misalignment spacers on the tie rod. No need for them on the tie rod as it will only see a very small amount of misalignment when you turn. The closer you can keep the heim to the knuckle the better. This cuts down the amount of force/ stress being applied to the through bolt.
I don't think that is possible. You would have to get hiems with smaller bores to match the bolt size. I forget the exact sizes, but something like a 3/4" heim with high angle spacers only uses a 1/2" bolt. If you removed the high misalignment spacers you would have a 1/2" bolt moving around inside a 3/4" hole in the ball of the heim.

Which brings me back to what I asked to check on before, what size bolts and what size holes are in the pitman arm and knuckle? I suspect that they were all drilled 3/4" and when the angles didn't work the misalignment spacers were added leaving too large of a hole for the bolt being used.
 

mock

Jr. Member
Joined
Jul 22, 2015
Messages
65
Loc.
Highland
Castor is definitely your friend, but looking at the pictures it looks like your front axle is pulled over to the passenger side, just based on the angle of the coil springs upfront Don’t know how this would affect steering, but your axle is not centered.
 

Qumanchew

Contributor
Full Member
Joined
May 16, 2018
Messages
317
Loc.
Kutztown PA
I don't think that is possible. You would have to get hiems with smaller bores to match the bolt size. I forget the exact sizes, but something like a 3/4" heim with high angle spacers only uses a 1/2" bolt. If you removed the high misalignment spacers you would have a 1/2" bolt moving around inside a 3/4" hole in the ball of the heim.

Which brings me back to what I asked to check on before, what size bolts and what size holes are in the pitman arm and knuckle? I suspect that they were all drilled 3/4" and when the angles didn't work the misalignment spacers were added leaving too large of a hole for the bolt being used.
Good points for sure. Now you have me also wondering what size the bolts are. I didn't think about that because I've always used 3/4" bolts and matching heims.
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
I don't think that is possible. You would have to get hiems with smaller bores to match the bolt size. I forget the exact sizes, but something like a 3/4" heim with high angle spacers only uses a 1/2" bolt. If you removed the high misalignment spacers you would have a 1/2" bolt moving around inside a 3/4" hole in the ball of the heim.

Which brings me back to what I asked to check on before, what size bolts and what size holes are in the pitman arm and knuckle? I suspect that they were all drilled 3/4" and when the angles didn't work the misalignment spacers were added leaving too large of a hole for the bolt being used.

There are options like these for 3/4” thru holes that I used to dial in angles on my rig. 1/4 to 1/2” height for 3/4” bolts on 3/4” thru holes. Nice hardware.

https://www.wfoconcepts.com/c-13933...ts-misalignment-spacers-standard-spacers.html

And even if those didn’t work, seems like simple work to machine a 1/2” ID to 3/4” OD close tolerance spacer.

Edit: looks like you’re in a similar situation as I was before making a custom drop pitman arm. Stock pitman arm wasn’t enough drop, and the drop arms (maybe approx 4” drops) were too much. My drag link went to knuckle too, but my track bar was quite a bit longer than stock.

Edit 2: the spacers I linked aren’t gonna make up that washer stack height

Edit 3: one idea I toyed with before making a custom pitman arm drop was using a 4” drop pitman arm and putting drag link on top vs bottom of pitman arm. Abandoned the idea for multiple reasons but might be a way to test what is your issue.
 
Last edited:

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
If a 3/4 bolt is tightened to spec the hole being close tolerance is irrelevant, at 350 foot pounds. The clamp load is 30,000lbs. I’ve had some steering components that used a 5/8 hole. The torque on that is 220 foot pounds and the clamp force is 23,000lbs. With that kind of clamp force the hole can be a little loose and there is no motion.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
What he's got is near perfectly parallel, so the combo of whatever that pitman arm is and those washer-spacers got him to the oft said ideal.
The problem is that the two links, the drag-link and the trac-bar, are not the same length. So there will be some bump-steer present. I'm doubting that's the whole of his complaint though. Lack of caster needs to be corrected first. Then ideally the trac-bar will get longer and it's attachment point on the axle will move further to the right side.
 
OP
OP
D

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
Okay, so here's a quick update. I put drop radius arm brackets on from tom's
It is definitely better. But still not fun to drive tire pressure is perfect i do need to bring the front axel center to the passenger side it is about one inch to the driver's side washers are not the problem, but I did make up a new spacer.
 
OP
OP
D

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
so i just my new adjustable track bar from 1 of the vendor YIKes i am not sure what its FOR but don't fit any thing i own
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
So what is perfect pressure? Based on the sidewall of the tire? Have you tried adjusting pressure? It makes a huge difference. My bronco drives like it’s on rails at 20psi, at 25 it begins to bounce and have to chase it, and I’m sure at the 65psi that is on the sidewall it would be undriveable, not that I’m going to be anywhere near them at that pressure with beadlocks so I haven’t tried.
 
OP
OP
D

dons68sport

Jr. Member
Joined
Jun 10, 2008
Messages
120
Loc.
brooklyn
I'm going to say not enough caster and tire pressure too high, both amplified by the bump steer from unequal track bar and drag link lengths. How much lift are you running?
3 inch lift 7 deg bushing lots of comments i will bring down the tire pressure drag links lengths where should i be number wise
 
Top