• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

How hard to fix? Transfer case leak

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
I drove around town in 4-wheel drive yesterday. After 4 or 5 miles, things got sluggish. It felt like I was dragging a stalled car. When I shifted out of 4-wheel drive and turned the hubs, things got better. Last night the garage smelled like gear oil and I found a nice puddle under the truck.

Is this an easy fix? It looks like the front seal blew, right? What else should I look for. I had this seal replaced when I got the bronco (it was leaking). This is the first time I’ve driven any distance in 4-wheel drive. Did the mechanic not install the seal right?

Any other thoughts?

Thanks,
Matt
 

Attachments

  • Leak1.jpg
    Leak1.jpg
    34.3 KB · Views: 194
  • Leak2.jpg
    Leak2.jpg
    16.9 KB · Views: 125

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
There is a seal in the retainer behind the yoke and also an o-ring between the yoke and washer (under the nut). It looks like both may be leaking.

Pretty easy fix if you have a socket to get the nut off. Drain the oil, pull the front driveshaft, put in tc in 4wd to keep shaft from turning, remove nut, washer, yoke, remove retainer bolts and retainer. Press out old seal, install new, put everything back together, add oil, put back in 2wd.

BTW it's not good to drive around in 4wd on hard packed roads.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I would check the condition of the front diff oil as well.
Also with it in 2WD and the hubs unlocked, try turning the front driveshaft. How well does it turn? If the front end is loading you down to where it felt like you were towing a dead car then you have problems in the front driveline somewhere that really should be looked at.

There is also the possibility that the gear ratios don't match between axles, that would cause the same problem. Have you had any axle work done?

As for if the seal was not installed right or not, it would have to come apart and inspect it. Anything from other stuff gone wrong, bad seal, or possible that it was not installed right. Could be the seal is fine but leaking through the splines of the yoke.

But we do not have a smoking gun, finger pointing answer for you.
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
Before getting too far along, be sure to check and make certain that it is the seals. It most likely is, but every once in a great while it can be the "cracked peanut" effect. That's when the case itself develops a hairline crack from some abuse. It is not impossible, as the D20 in the Chariot has carried a cracked peanut for most of its life now. And yes, you can see the crack. It just is that it is so fine, that I have never done anything about it. Probably not your problem though. But just check and make sure.
 

Baja71

Bronco Guru
Joined
Oct 16, 2004
Messages
2,908
Why were you driving around town in 4WD? Were these snow packed roads or pavement?
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
Why were you driving around town in 4WD? Were these snow packed roads or pavement?

We had lots of snow then some rain. I live up on a hill and the roads near my house were very icy and slick. When I got into town, the roads were just wet.

I haven't had it in 4WD since I bought it. I wanted to see how it would do on the ice. It was a ton of fun until I hit the wet roads and someone strapped a boat anchor to the back.
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
I pulled the drive shaft out tonight but couldn’t get the yoke nut off. I have a socket (1 1/8), but couldn’t break it free.

It is definitely leaking from the flange and maybe the yoke. I pulled the 4 flange bolts out and oil poured from the bottom bolt.

I’m not sure if I want to go any further. I don’t want to screw it up. I didn’t try to put an impact on the yoke nut. Should I? How tight should it be? If it’s on there that tight, will I be able to get it back on.

I don’t have a press and I usually shy away from gear, bearing, and tranny work. Should I go for it or take it to someone?
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
Also with it in 2WD and the hubs unlocked, try turning the front driveshaft. How well does it turn?

It turned pretty well--nice and smooth with little resistance. It didn't seem to bind at any point. One of the caps fell off the front U joint so I may get to replace it. I'll check the fluid too. Thanks for the tip.

Matt
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I pulled the drive shaft out tonight but couldn’t get the yoke nut off. I have a socket (1 1/8), but couldn’t break it free.

It is definitely leaking from the flange and maybe the yoke. I pulled the 4 flange bolts out and oil poured from the bottom bolt.

I’m not sure if I want to go any further. I don’t want to screw it up. I didn’t try to put an impact on the yoke nut. Should I? How tight should it be? If it’s on there that tight, will I be able to get it back on.

I don’t have a press and I usually shy away from gear, bearing, and tranny work. Should I go for it or take it to someone?

An impact would make it easy. The torque on the nut is about 150 ft-lb. Once the nut is off the only things that can possibly come off are the washer, o-ring, yoke and flange. The seal is in the flange. You won't need a press.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
We had lots of snow then some rain. I live up on a hill and the roads near my house were very icy and slick. When I got into town, the roads were just wet.

I haven't had it in 4WD since I bought it. I wanted to see how it would do on the ice. It was a ton of fun until I hit the wet roads and someone strapped a boat anchor to the back.

Go into the tech section on the left. Find the "find gear ratio" article. Lock the hubs but leave the transfer case in 2WD. Make sure you have the same ratio front and rear. I have a very strong suspesion that you are the victom of mixed axle ratios from some prior work before you got it.
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
Thanks for the help everyone.

I got the nut off with a little WD-40 and a breaker bar. The seal was bad and I didn’t see an o-ring. It looks like someone tried to fix the leak with RTV or silicone. The yoke nut had a thick layer of silicone around it.

I got everything cleaned up. Now, I just need to find a gasket for the flange.

I’ll check to if I have mismatched front and rear gears. Hopefully not.

Thanks
 

Baja71

Bronco Guru
Joined
Oct 16, 2004
Messages
2,908
Sounds like you might have a mismatch if it happened just as you hit the pavement. A part time 4WD is not supposed to be driven where there is good traction (even wet pavement gives good traction) but you should be able to drive OK for a little while or until you start turning and such. If this was immediate, you may have the mismatch. If it was drastic mismatch, you'd have broken something fairly quickly.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I got the nut off with a little WD-40 and a breaker bar. The seal was bad and I didn’t see an o-ring. It looks like someone tried to fix the leak with RTV or silicone. The yoke nut had a thick layer of silicone around it.
The o-ring is supposed to seal between the yoke and the shaft. If it's there, it will either be inside the transfer case, on the shaft, or underneath the washer behind the nut on the yoke. Usually the o-ring doesn't seal that well. I've had good success using the RTV (silicon) sealant. Install the yoke, then put RTV around the shaft, underneath the washer. Install the washer and nut, and tighten.
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
The o-ring is supposed to seal between the yoke and the shaft. If it's there, it will either be inside the transfer case, on the shaft, or underneath the washer behind the nut on the yoke. Usually the o-ring doesn't seal that well. I've had good success using the RTV (silicon) sealant. Install the yoke, then put RTV around the shaft, underneath the washer. Install the washer and nut, and tighten.

Thanks Steve. I'll give that a try.
 
OP
OP
MattM

MattM

Jr. Member
Joined
Apr 2, 2007
Messages
146
Loc.
Missoula, MT
Just a quick update for anyone interested.

I checked the front and rear axle ratios as discussed in the tech section. (The string trick worked well.) Both drive shafts rotated the same distance—about 3.5 rotations per wheel rotation. I think both front and rear are 3.55.

I installed a new oil seal, but couldn’t find a retainer gasket. I bought some Permatex Good Stuff for the retainer. I used RTV under the washer and put it all back together. So far, I don’t have any leaks.

The retainer has three cracks—at 3 of the 4 bolt holes. It looks like someone tightened it down too much. Two of the three are hairline cracks and one is larger. I re-used the retainer anyway and added a little more Right Stuff at the cracks.

So far, everything is good.

Thanks for all the help.

Matt
 

samamarshall

Full Member
Joined
Nov 3, 2008
Messages
244
I had the same leak. Ordered a new seal, opened it up, and realized my yoke was worn down just a slight amount which caused the seal to...well not seal. New yoke was an option, but costs $$, so I created a spacer with large washer to move the flange slightly farther out, letting the seal make contact with the unworn shaft....hope this makes sense...
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I had the same leak. Ordered a new seal, opened it up, and realized my yoke was worn down just a slight amount which caused the seal to...well not seal. New yoke was an option, but costs $$, so I created a spacer with large washer to move the flange slightly farther out, letting the seal make contact with the unworn shaft....hope this makes sense...

I see two potential problems with this method. First, the seal flange width is used to set the correct endplay of the front output shaft. The spec for endplay is .003-.005". Moving the flange forward or back may throw the endplay way out depending on where the washer is used. Second, moving the flange out will cause the mounting ears to be unsupported by the case. These ears break easily.

A better solution would be a speedi-sleave on the yoke.
 
Top