• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Is this "normal"

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
Couple questions, trying to do a thorough cleaning/inspection
of front and rear axle.

Front- Just removed the cover off dana 44, this is what the inside looked like. Is it normal to have this rust inside? It's also on the top half of the inside cover. I tried cleaning it but seems not to come off.

I have seen different opinions on gasket only, no gasket just rtv (black some say only use gray, and I have also seen use both gasket and rtv), what is the census here, what has worked best for you? What's the torque on these?

Rear- (Ford 9") confirming to change the gasket you have to remove the (3rd member), should this just slide out smoothly or are there more steps to remove it how about reinstalling it? Same question as above for gasket? I also read that there should be copper washers underneath the nuts for the 3rd member, mine do not have any ( not saying they never did, they may have before when I got work done to it, but there not there now, should I get some before reinstalling? It also says these are torqued 30-35 ft-lbs, is that right?

If I missed something please let me know.

Thank you in advance for your time/help,

Sonny
 

Attachments

  • 20201220_103948.jpg
    20201220_103948.jpg
    153.3 KB · Views: 185
  • 20201220_103904.jpg
    20201220_103904.jpg
    148.7 KB · Views: 210
  • 20201220_103855.jpg
    20201220_103855.jpg
    108.8 KB · Views: 201
  • 20201220_103848.jpg
    20201220_103848.jpg
    148.7 KB · Views: 187

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
Looks like nobody engaged the hubs for like a million years!


Sent from my Pixel 4 XL using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, to remove the Ford 9" differential you must pull the axle shafts out at least 6 inches. Most guys would remove the axles and inspect the bearings. Then after all the nuts are removed the diff slides out, but may be stuck or held in by silicone. Be careful, it may be heavier than you think. And before it loosens, be ready to catch a few quarts of some nasty rear end grease.
I know Ford used copper washers the 9" rear ends. I don't know if all rears got them. Most of the rears don't have them anymore. Once they get distorted they are a pain to reuse and really not needed.
I think using a gasket or just silicone sealer is a personal preference. I haven't used a gasket in many years. Some modern silicone will work on an oily wet surface. Years ago the metal had to be clean and dry.
Good luck
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Not normal, or shouldn’t be normal anyway. Needs to come apart and be cleaned up. Replace the axle seals in the housing, I expect that’s where the water got in, or the vent, needs to be checked out. Seal it all back up and put fresh gear oil. Use a gasket or RTV, both work, I usually use a gasket with a thin coat of RTV.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
ARB is the second thing I noticed after the rust. Someone got water in the axle and never serviced it. Short answer, it needs a rebuild. Rust is very abrasive and will kill what good parts are still in there.
 

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
I don't think anything's toast. Differentials are tough!

Fill it with Morys gear oil and engage the hubs for the next 500 mi., Even if you aren't in four-wheel drive and then try out the ARB. Probably better if you don't engage four-wheel drive until the differential is fully lubricated.

Prime suspect is the differential vent on the top. Probably wide open letting water in.

Sent from my Pixel 4 XL using Tapatalk
 
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
Yes, there is an ARB in there. Connected to the signal compressor.

Thanks for the reply s, not what I wanted to hear but what I FEARED!!! I just had it at a shop for some other things and asked if they could take a look at the front/rear since it was there, guess it was never checked. The reason I removed the cover was because when I checked the fill plug and the oil looked dirty which didn't seem right since I have put (0 miles) on it since I got it back, that's the only reason I thought I would do a inspection. What would happen if I were to continue driving /going offroading with the parts in this condition?

Well I haven't even opened the back yet hope no more issues. So if these parts are shot, what is recommended to put back in (ARB again or something else, parts/numbers if you have it?) Is this a hard/complicated project thats needs to be done at a shop or can it be done in a driveway/garage?

What else should be done (replaced) during this project?

Obviously it's been awhile since I purchased the ARB, with everything that needs to be replaced, approximately what should I be looking to spend?

I appreciate everyone s help,

Sonny
 
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
The differential vent ontop has a vent with vent hose connected than ran up inside the fender, not open.

Could it be from somewhere else, what should I check?

Sonny
 

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
So I run my differential vent up inside the fender and then I point it down with a fuel filter on the end of it. That way no water or rain can get into it, unless the water was up over the distributor

Sent from my Pixel 4 XL using Tapatalk
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I don't think it is shot. The ring gear looks remarkably good.
But it does need going through to prevent the rust from mixing with the oil, in which case it will be "shot".
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
It is sooooo worth it to pull it apart BEFORE running it. What you don't want to risk (your option) is to break loose some rust and mess up some brgs, mess up some ARB seals, etc.

It's not worth it IMO because if the vent line is hooked up correctly probably the only way enough moisture got in there to mess it up would be an axle seal, maybe when they installed the ARB?

How long have you owned it?

When was the ARB installed?

When do you last remember it being in deep enough water to cover the axles possibly allowing water past the axle seals?

Be curious to know if the rust is surface rust like dew on sheet metal or possibly some 3 yr old flakey rust in places we can't see in the pics.
 
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
That's what doesn't make sense:

I have owned it 20 years, I had the ARB I stalled 20 years ago and have had them "serviced " a couple years ago so I thought , who knows now a days , I have not had very good luck with shops lately with any of my vehicles and believe me I do my research, but if it wasnt for Bad Luck I would have No Luck at all.

I dont recall going through deep enough water.

What other possibilities are there?

What other photos or angles can I provide that might help? *I know its impossible to diagnose from pictures, but at least it would help narrow down the issue.

So if the ARB is salvageable, what steps do I need to take/do to clean it up right to prevent further damage .

Thank you for the replies. I am still learning, so if I ask a dumb question, I am not pretending. I hope I am not the first one to have this issue but I hope someone will be able to learn from what I may have done wrong if anything , I reali8after trying to research this issue, these fluids should be changed on a semi regular basis.

Sonny
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Welcome, we have ton's of experienced guys that can help ya out!! :)

Fluids can last a long, long time but when they are compromised... not so much. Somehow, water got in there... what color was the gear oil that came out?

Anyway, start another post on the "Bronco Chat" forum maybe to ask for recommendations on decent reputable shops somewhere close to where you live.

Somebody will steer you towards a shop that can help you out... that's the key. You're from S. Cal so there are lot's of guys that should steer right towards a good shop.

What you need done, is not technical stuff for a shop. If you haven't engaged the front end then they quite possibly just need to pull parts, clean then up and put it back unless the brgs are rusted also.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I answered a PM, but what I suggested was to take it apart. Give it a dip in something like evaporust. Inspect. Probably avoid putting the ARB seals in the juice, not sure if they would be safe or not.

Unless absolutely sure, put a set of bearings in it. As long as the gears are usable and you keep track of all the shims, no setup needed.

What I see of the gear teeth, I don't see any pitting to worry about.

The sucky thing is there is a lot of labor and probably very few parts. Probably more labor than just putting the gears in since there is rust to deal with.
 

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
My guess is that the ARB mechanism is toast considering the differential is what is rusted in the picture. Gonna have to take it apart further and see what you find.

Gotta run the 4wd every once in a while to keep things lubed up. Even just once a year for 2 mins at 20 mph would probably do it.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
But you live in So Cal... humidity must average 30-50%? Not exactly Florida or Georgia humidity levels so that's why I think you have a seal that allowed water in.

So what color was the fluid? Carmel? Black oil with water that drained out of the diff FIRST when removing the cover?
 

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
But you live in So Cal... humidity must average 30-50%? Not exactly Florida or Georgia humidity levels so that's why I think you have a seal that allowed water in.

So what color was the fluid? Carmel? Black oil with water that drained out of the diff FIRST when removing the cover?

I know I'm not the one you are directing your comment to, but it is 17% humidity in Socal right now... It's been terrible the past couple weeks with the wind. I am also surprised to see that much rust on anything in SoCal if you aren't near the beach.
 
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
The fluid that came out of the front dana 44 was like a thick Carmel color.

I live in the LA/OC area about 30 miles from the beach, not sure if that's close enough to cause these issues?

When I drained the fluid out of the rear 9", it looked smooth and "clean".

So by the sounds of it, it doesn't sound like it's going to be "salvageable ", but we really won't know until I get in there.

Can this all be done on the vehicle or does it have to be done on a bench? If I have to purchase a whole new set up, is everything included with the ARB system (gears/ring/pinion/seals) or are they all separate?
**Assuming this can be done on the vehicle **
With everyone's help and researching videos, please correct me if I am wrong with the steps I need to do;

(1) fluid already drained/cover removed
(2) remove/or at least take one side of the tie rod off (to be able to remove the ARB/gear without dropping it (does the pinion also have to be removed and replaced?
(3) clean /wipeout the inside of the axle (using brake cleaner. Do you use a thing else to knock off/remove any rust that may be on the inside of the axle assuming because of the rust on the parts we can see, there must be some on the inside where we can't?)

Am I on the right track?

Sonny
 
Top