• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

mass air sensor location

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Any thoughts good or bad on this placement. I was thinking of attaching it to the engine at the alternator, with an air shield along the radiator.
 

Attachments

  • DSC03231 (Medium).JPG
    DSC03231 (Medium).JPG
    84 KB · Views: 146
  • DSC03232 (Medium).JPG
    DSC03232 (Medium).JPG
    87 KB · Views: 137

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Looks a little close to the header. Maybe add a bracket off the inner fender that raises it up a few inches.

Very clean and somewhat familiar looking setup.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I'd definitely put a heat shield over those headers (both banks) and get the MAF away. And that open-element filter right in the blast of the fan isn't helping. An enclosed filter with a cold-air duct will perform better, last longer, and look cleaner.

But the rest of the engine looks NICE! ;) The only other thing I'd add would be wire guides.

.
 
OP
OP
behemoth

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
The inner fenders have been raised up close to 4 inches so I am limited in space on top of them for the maf. I was planning on making a heat shield as well as a fan sheild to keep the air from the fan off of it. Any issues with attaching the maf to a bracket attached to the alt, will it shaking with the engine be a problem.

I will look at the wire tiedowns and see what I can work out on them. I have only started this thing for testing no real run time yet.

I was thinking of running the intake tube out through the inner fender and have the filter in the inner fender up by the sidemarker light. So much work has already been done I am tired of messing with the inner fenders.

Thanks It has been a long time getting it to this point.

Bill
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Hard to say if the shaking would shorten the life or not. I know the wire elements are pretty delicate inside the MAF but their mass is small.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Any issues with attaching the maf to a bracket attached to the alt, will it shaking with the engine be a problem.
It shouldn't hurt the MAF, but the further you get from the opposite engine mount, the more motion there is, so it'll need more clearance around it for the engine to rock. That's one reason Ford makes the hose flexible & mounts the filter/MAF to the body.
...have the filter in the inner fender up by the sidemarker light.
That's how I did Frank's, but on the other side.

 

WheelHorse

Bronco Guru
Joined
Nov 22, 2004
Messages
2,511
Run a hose to the inner fender and put the filter on the other side of it.

Rubber mount your maf to a bracket mounted to your wheel housing.

Under-the-hood air is dirty air, MAF's will work, but aren't particularly happy or give the best performance.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Crown Vic, which is the same as a Mustang. But the Mustang is installed facing R, and CV faces L. That style of upper intake (plenum) is reversible. Most of the ones that look like it (TB in the center) are reversible, but the TB & everything else might have to be changed to make it work the other way. Since we took Frank's intake from a CV, we just kept it facing L, like the FS trucks.
 
OP
OP
behemoth

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
viper, I noticed in your gallery how you have yours setup. Is this current and working well for you?
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
steve 83 what vehicle did that airbox come out of?
I wish I had written stuff like that down... :-[ It might have been an early SHO Taurus. Whatever it is, it fits perfectly - right down to the angle on the bottom. It's bolted through its original holes directly to the wheelwell. I think the only mod was to cut another hole out the side (facing the fender) to make sure enough air got in. The rubber elbows were just lying on the ground in the JY, so again: I can't be sure about their sources, but I have the vague impression one came from a GM V8 muscle car (like a T/A). The box originally had a MAF, but I deleted it since his engine didn't need it, and to make the turn for the hard pipe. The pipe might be a section of dryer duct, but since Frank wrapped it in that black tape 8 years ago, I can't remember.

In any case, it's all working great. He drives it every day on- & off-road, travels in it, and tows his boat or 4-wheeler & dog trailer.
 
Top