• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Need Brake Help-might be fixed(READ)

blazinchuck

Bronco Guru
Joined
Jul 14, 2005
Messages
3,319
Alright guys, here's the deal. It's a 1974 bronco.

1st I change from drum/drum to manual disc front/drum rear on the EB axles

2nd changed to full widths 44/9" with ford disc front/chevy disc(1/2 ton truck)rear.

I bought a new booster/MC from ebay. Mounted it all up and no good pedal!
I put the old f250 MC I was using w/manual disc(on the EB axles) and had a great pedal-problem was the rear brakes were dragging really bad...rear smoking after 1 mile run!
So I did what others said, and bought a lincoln MC from a '79 mark V. I could never get a good pedal. I bled,bled,and bled...still no luck! I counldn't even get the front to gravity bleed! So today, I thought I would try yet another lincoln MC from the store-thinking the one I had was faulty. I installed it, bled the system again...no F*cking brakes still:mad3: I even eliminated the H-block mounted to the frame using unions. Now there is just lines from the MC to the front and rear main brake lines(nothing else). I bled everything again-still no brakes. I have adjusted the pedal rod 'til it feels right over and over. Still no brakes. I have to pump atleast 4-5 times for a somewhat firm pedal, let it up and hit them again- no pedal!!:shaking:

WTF!!!!
heres a pic for those that need something to look at while reading!

I would like to fix this today, gotta do some local wheeling tomorrow!!!!
IMG_0066-1.jpg
 
Last edited:

TJK74

Bronco Guru
Joined
Feb 21, 2003
Messages
3,154
Loc.
Newark CA
I had this simialr no pedal problem when i went to manual disc and like you even swapped the MC over and over and bled the system over and over and over. I finally ended up lengthening the pedal to MC rod by just under 1/2" and instantly had solid firm pedal. Sounds like you have already tried adjusting your though so not sure if my idea will help.
I was using the stock pedal rod on a f250 camper special MC and was having to pump the pedal 2-3 times to get the thing to stop.
 
OP
OP
blazinchuck

blazinchuck

Bronco Guru
Joined
Jul 14, 2005
Messages
3,319
I have plenty of adjustment on the pedal rod to the booster. I ran it in 1st because of the rear brake dragging. Now I lengthen it some to make up for the newer MC. I hate to install the f250 MC again, because of having to bend those 2 lines again...they hook up on the driver side-not the motor side!!!
 
OP
OP
blazinchuck

blazinchuck

Bronco Guru
Joined
Jul 14, 2005
Messages
3,319
what a huge difference ED!!! I haven't tried everything just yet, but now I have a pedal-A firm pedal! I'm sure this is the fix.

To clue all those who are wondering whats up...Ed suggested I check the length of the rod going into the MC. Well, I've already said the f250 worked good, but nothing else would.

I measured the depth of the hole on the f250 (1.375") and the lincoln was (1.415"). So I began inspecting the rod going into the MC from the booster bracket...it has a small adjusting bolt/lock nut. I screwed this out a few threads(about 4turns).

Wahlaa!!! Firm pedal! I will still test everything out good, and post the results...Thanks A bunch ED!!Chuck
 

TJK74

Bronco Guru
Joined
Feb 21, 2003
Messages
3,154
Loc.
Newark CA
Chuck
I thought that was what I had suggested to try in the first reply to your post.
;D ;D ;D
 
OP
OP
blazinchuck

blazinchuck

Bronco Guru
Joined
Jul 14, 2005
Messages
3,319
pedal to MC rod by just under 1/2"
Well, I read that as the pedal to the booster bracket;) I didn't know there could be an adjustment between the bracket at the MC;D Thanks though,Chuck
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And just to back up a bit, when your rear was draggin' (the Broncos, not yours), was the F250 MC you were you using from a disc/drum setup? I assume yes, but wanted to make sure.
The reason I ask is that if you didn't remove the residual pressure check valve from the MC (if so equipped), then that could have caused the dragging issue.

Paul
 

nirvana

Jr. Member
Joined
Oct 13, 2006
Messages
118
Loc.
PNW
And just to back up a bit, when your rear was draggin' (the Broncos, not yours), was the F250 MC you were you using from a disc/drum setup? I assume yes, but wanted to make sure.
The reason I ask is that if you didn't remove the residual pressure check valve from the MC (if so equipped), then that could have caused the dragging issue.

Paul

please elaborate,...i need to know!!??? i've been trying the same stuff..and also,..which of the M/C's were the ones you want?...i have the stock rear drum and Ch**y front disk. please help, thanks guys
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
please elaborate,...i need to know!!??? i've been trying the same stuff..and also,..which of the M/C's were the ones you want?...i have the stock rear drum and Ch**y front disk. please help, thanks guys

Never played with different MC's myself. I'm still using the stock '71 type with the valve removed. Works sweet with the Ford disc setup that I've got.

Residual pressure check valves are used in drum (and some disc) systems to keep the return pressure, exerted by the springs on the brake shoes, from pushing the fluid back into the MC every time you let off the pedal.
If you allowed that to happen each time, you could have a very soft or inconsistent pedal because you had to push the shoes farther to contact the brake drum.
Disc brake systems don't have springs trying to return when you let off so don't need as strong a valve and can actually get away with no valve in most cases.
Some valves are external in-line units and some are inside the MC itself (like in the case of the Bronco MC).

Some disc systems don't use any valve at all and some use a minimal check valve resistance. Aftermarket companies sell them in different ratings, like about 2 psi for a disc setup and about 7 to 10 for drums. I could be off on the exact numbers, but that gives you the basics.

To remove the one from your front discs, follow the line up to the MC so you have the correct port. It's usually the larger, rearmost reservoir on ours, so it's the rear port you're looking at. Always verify though, since someone could have changed it over the years.

The idea is to pop out the brass cone seat and pull out the spring, plastic piston-like thingy (for lack of a better word) and the ball (a little BB sized thing).
I'm sure there's a tool for this, but I used a properly sized sheet-metal screw and just screwed it into the opening in the cone and pulled out. Obviously you're trying not to damage the seat since that helps avoid future leaks.

Then you put the cone seat back in and.. Voilá, you're done.

Clear as mud? Welcome to the New Year!!!! Hah!

Paul
 

TJK74

Bronco Guru
Joined
Feb 21, 2003
Messages
3,154
Loc.
Newark CA
The MC I used was the 78 f-250 camper special. I tried using my stock 74 MC and decided to pull the residual valve with the screw method. Well as my luck goes the freakin screw broke in the MC inside the brass cone. So with that said and done I went and picked up the camper special MC;)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hah! Bummer. Good excuse to get the bigger MC I guess though?

Paul
 

nirvana

Jr. Member
Joined
Oct 13, 2006
Messages
118
Loc.
PNW
Thanks Paul! That was made very clear. i have a feeling that this is what i need to do, as my front brakes drag. and ive gotten tired of the whole thing. i have forgotten now what M/C i put in though i just recently redid my system, with little results in improvement. :( i fiqured i would have outstanding brakes with the air assist and front disk, but my pedal is soft and the fronts hang,...
i may go for a Versailles M/C or F250 and do the Trick you taught me! Thanks again , Len
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sounds good. Don't forget how important that push-rod adjustment is to pedal travel though!
Everything works together as a system.

Paul
 
Top