• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Nuetral safety switch

Iowabronco68

New Member
Joined
Oct 7, 2009
Messages
34
Been a while since I have owned a Bronco but just purchased a 73 automatic, Previous owner put a new neutral safety switch in it but still have to move the column shifter around to start it, Is there an easy bypass for this until I get time to work on the switch ?
 

NGABronco

Contributor
Always Learning
Joined
Feb 4, 2007
Messages
7,574
Loc.
N. GA now South Carolina
Do a search in the tech section, it's an easy adjustment, loosen a bolt, stick a pin in and retighten the bolt. It's worth taking the time from a safety point. Good luck!!!;D;D;D
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Did a search but didn't come up with much.

Block the wheels and set the parking brake. Loosen the linkage nut on the trans lever so the linkage rod can move freely. Move the trans lever to the neutral position. That's 2 clicks down from the park position. Make sure the column is set to the neutral position. You might need to have someone hold it there. Now tighten the linkage nut. You may need to readjust the neutral safety switch (NSS) after this.

Loosen the 2 small bolts holding the NSS. Block wheels and place trans in neutral. Insert small pin (1/16" drill bit) in hole in side of NSS. Adjust NSS body back and forth until pin can be pushed into hole approximately 1/2". Tighten NSS bolts.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Check the linkage bushings as well. The switch may be working better then the shifter is.

In high school I knew a guy who run his cougar into a garden center because it didn't start with the key, but he knew how to jump the solenoid. Bushings shot, shifter in park, transmission in reverse. Neutral safety switch was working perfect.
 
OP
OP
Iowabronco68

Iowabronco68

New Member
Joined
Oct 7, 2009
Messages
34
Finally got a chance to get under the Bronco, got it where it will start just a hair off park but not when lockled into park.I adjusted the switch itself also, do I need to do anything else to get it so it will start when locked into park. And thanks to you also NGABronco !
 

NGABronco

Contributor
Always Learning
Joined
Feb 4, 2007
Messages
7,574
Loc.
N. GA now South Carolina
Hey Iowa, go back to what Viper said, get the linkage on your shifter set right first and then adjust the NSS. If it's cranking just out of park, it may crank just out of neutral or in drive. You really want it to only crank in Park and Neutral.
Good Luck!!!;D;D;D
 
OP
OP
Iowabronco68

Iowabronco68

New Member
Joined
Oct 7, 2009
Messages
34
I loosened the nut on the linkage and then moved the lever to neutral, tightened it back up but when I tried to put it back in park it would not go all the way in ?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I loosened the nut on the linkage and then moved the lever to neutral, tightened it back up but when I tried to put it back in park it would not go all the way in ?

Might need to have someone hold the column in neutral while you adjust.
 

browngr5

Full Member
Joined
Oct 6, 2010
Messages
218
Loc.
Eagle, Idaho
Check the rivets on switch housing while your under there. I had 4 switches separate within the first year and quit working then eventually the guts fell out. I learned to drill out and replace with slightly larger rivets.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
And while I have not heard any complaints about neutral safety switches, we know that generally newer parts are not nearly as reliable as the old stuff in some categories. Like switches.
So your almost-new switch might actually be failing. Hate to make you throw money at something that just needs fiddling, but once you've tweaked it to within an inch of it's life, don't rule out a new switch maybe being needed soon.

Very common with starter relays/solenoids, and a few other things. Not so much with NSS' but maybe we just don't hear about them as often.

Good luck.

Paul
 
OP
OP
Iowabronco68

Iowabronco68

New Member
Joined
Oct 7, 2009
Messages
34
I haven't had a chance to crawl back under it yet, did a few other things to it today. Will post some pics
 
OP
OP
Iowabronco68

Iowabronco68

New Member
Joined
Oct 7, 2009
Messages
34
Got it taken care of today, had a buddy hold it in neutral while I tightened the linkage. Starts when locked in park. Thanks everyone for the help !
 
Top