• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Project: 76, Orange Special Decor

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
I'm thinking the holes in the J cap could be oversized once marked to make alignment a lot easier and would allow you to keep the cap tight against the edge of the ABS. Snug the bolts down to hold everything in place.
 
OP
OP
gnsteam

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Exactly what I was thinking. Today I will study the situation and get some measurements.
 
OP
OP
gnsteam

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Recovering from an early season cold. I got into the warm shop today, to address the steering column, turn signal canceling cam. I designed and machined one on my own. Details can be found at the following thread.https://classicbroncos.com/forums/t...-for-ididit-column.331694/page-2#post-3647499
a358d226-8482-4389-be4f-a067ab33113d-1_all_6383.jpg
 
OP
OP
gnsteam

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Yesterday, I finally got back to the headliner. Experimenting with the J Cap material, brought to my attention by member, .94 OR. I started with one of the short sections of the front headliner section. The liner mounting flange in my situation required a lenght of J Cap, 22 3/8" long with three mounting holes.
a358d226-8482-4389-be4f-a067ab33113d-1_all_6399.jpg
The original thought was to mount the J Cap's long width (1") between the liner and the hardtop. And using the shorter 1/2" side as the exposed edge. This did not work out for me. Because the pre existing holes in the liner were not the same distance from the edge of the liner. And they were not far enough from the edge of the liner. To place the clearance hole in the J Cap, to allow clearance for the fasteners head. With out a clearance radius in the short section of the J Cap. So to make it work as first planned. I would have to slot out all the holes in the headliner material to place the hole in the J Cap. Away from the short side lip, for bolt head clearance. Here are a series of pictures showing the hole location variance with in this J Cap section.
a358d226-8482-4389-be4f-a067ab33113d-1_all_6402.jpg
a358d226-8482-4389-be4f-a067ab33113d-1_all_6401.jpg
I used the headliner material to transfer the hole locations to the J-CAP. Because those holes were used to locate the nutserts in the hardtop. I used my milling machine to drill and clearance the short lip of the J-Cap. Seeing this variation in hole locations. It was decided to use the long side of the J-Cap, as the exposed side. Which looks just as good and the hole location variation isn't that noticeable. The clearance radius is still needed, to clear the nutserts diameter.
a358d226-8482-4389-be4f-a067ab33113d-1_all_6398.jpg
a358d226-8482-4389-be4f-a067ab33113d-1_all_6397.jpg
I do like the finished edge much better than just the wavy edge of the ABS headliner material. Worth the added time and expense? I think so. More to come as I get to the rear section of the headliner.
 

Attachments

  • a358d226-8482-4389-be4f-a067ab33113d-1_all_6400.jpg
    a358d226-8482-4389-be4f-a067ab33113d-1_all_6400.jpg
    210.4 KB · Views: 19

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
I'm glad you are finding a solution for the narrow exposed edge past the fasteners. I watched that after you posted photos and thought maybe I had sent you down a dead end. That wider trim edge still looks pretty decent since it has the radius edge transition to the top metal.
 
OP
OP
gnsteam

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Not a dead end, no worries. I'm still satisfied with the result. The trim does look better than the wavy, natural edge of the ABS liner.
 
Top