• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Question on Bilstein 7100's please

FASTERDAMITT

Sr. Member
Joined
Nov 20, 2006
Messages
806
Loc.
Oceanside
I know alot of Bronco owners run them. I currently run Fox 2.0 non resi but need to change the valving some because I bought my son a Toyota Total Chaos set up truck and he leaves me in the dust with my soft shocks. Has anyone run at a decent speed with the 7100's reservoirs 360/80 valving through desert or rough terrain with our softer springs? I run BC 4.5" coils.
 

ken75ranger

Bronco Guru
Joined
Jan 27, 2002
Messages
5,069
Loc.
Troy, NY
Fox shocks are pretty good for the money. If yours are in decent shape give Fox a call and ask about revalving and adding remote res.
 
OP
OP
FASTERDAMITT

FASTERDAMITT

Sr. Member
Joined
Nov 20, 2006
Messages
806
Loc.
Oceanside
I will revalve my rear shocks but for the front I am going longer and I don't currently have reservoirs but would like them for the longer runs. 14"s in front and 12"s in rear.
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
I have been researching the Fox products recently and am ordering a set of Fox 2.0reservoir shocks tomorrow, actually.

They will revalve them for you, for sure, usually the first revalve is free. As well, you can add a reservoir. If you add the reservoir, you can also add a compression dampening adjuster (it can only be added/purchased ($75) with the reservoir option), which allows you to tune the shock with 8 different settings (for a total of a 20% change in the valving--pretty sweet). Fox or one of their vendors (Offroad Warehouse or SDHQ) can definitely rebuild them however you like....and that will likely be much cheaper for you than buying new Bilsteins...even with the above mentioned upgrades. The Fox stuff is supposed to be easy to rebuild and revalve, if necessary, and the parts are supposed to be more widely available than the Bilstein stuff from what I have been reading.

Hoping that this will be a sweet upgrade...not that I am unhappy with how the Bronco rides now-at all. But the front DS pair of Cage shock bodies were/are damaged so they need to be replaced...since I cant get the Cage-stuff anymore, I am going to upgrade and go single shock at each corner. It should be sweet to have the adjustability for in town/off-road/highway travel.

Good luck with getting your Fox shocks revalved and/or upgraded.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
I have the 14" short bodies, (360/80 valving), they work amazingly well, I haven't experienced any fade from heat, but I don't run a whole lot of up travel. I'm more set up for crawling. I do play in the desert quite a bit, since I'm local to socal. The only upgrade from the 7100's, would be a coil over set up.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
I know alot of Bronco owners run them. I currently run Fox 2.0 non resi but need to change the valving some because I bought my son a Toyota Total Chaos set up truck and he leaves me in the dust with my soft shocks. Has anyone run at a decent speed with the 7100's reservoirs 360/80 valving through desert or rough terrain with our softer springs? I run BC 4.5" coils.

I'll chime in with my $0.02 that echoes others' sentiments in this thread. Stick with your Foxes and have them re-valved or get them upgraded with a reservoirs, etc. You'll be happy. Be advised that no matter what you do, an IFS Toyota with a TC kit on it will leave your Bronco in the dust - you can't beat physics. 14" travel shocks sound pretty long for the front - watch to make sure you're not using them as bump stops if they're that long.

Todd Z.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
I'll chime in with my $0.02 that echoes others' sentiments in this thread. Stick with your Foxes and have them re-valved or get them upgraded with a reservoirs, etc. You'll be happy. Be advised that no matter what you do, an IFS Toyota with a TC kit on it will leave your Bronco in the dust - you can't beat physics. 14" travel shocks sound pretty long for the front - watch to make sure you're not using them as bump stops if they're that long.

Todd Z.

exactly, its cost me A LOT of money to keep up with my a arm and i beam buddies.
be aware of the longer shocks like stated above, stock mounted eb coils generally will not cycle more than 10in travel vertically. dont know what springs you have, but my old wild horses 5in rock crawler coils cycled 10in at most vertically, measuring from the axle hanging to full coil bind.
you would probably benefit more from leaving soft valving of your current shocks and adding a 2in travel hyd bumpstop. its only money, how fast you want to go? :cool:
 
OP
OP
FASTERDAMITT

FASTERDAMITT

Sr. Member
Joined
Nov 20, 2006
Messages
806
Loc.
Oceanside
Thanks for the input. I lowered my front shock lower mount from the top of the radius arm to the side and gained 2" of travel. Of course this is with the Duff shock hoops also allowing 25" eye to eye. I have my bumpstops set up to start working 3"s into the travel. My total travel is 6"up and 6" down with this setup and Fox 12" shocks. I still have 1" of shock up travel left even after hammering my soft/medium valving so i should be safe there. If i was to stay with Fox I will have to keep 12" length. If I went with the 7100's I could run 14' short bodies. I wish I could get a straight comparison on how 360/80 Bilstein compares to Fox 50/70 valving. ORW, Raceshock and Kartek can't answer directly. BTW, I am seeking more rebound control as when the bump compress's it comes up to quickly for my preference. The compression is close.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
you would be surprised most of the time when suspension "rebounds to quick or bucks" it is not the rebound being to light, its the compression being too light and bottoming out to fast. if you order off the shelf kings, they will be .015 compression shims and .012 rebound. my old coilovers had .015 compression(little too soft) and i went as low as .008 rebound. you want fast rebound with a solid axle if you doing fast passed stuff. the axles like to pack up the suspension and no rebound. is the 50/70 compression then rebound or the other way?
i find it a little hard to believe your using full 12in of travel with a stock trackbar/panhard bar. the side to side axle swing gets pretty crazy with more than 10in travel.
put a zip tie on your shockand push it to the body and see howfar down it gets pushed after using the truck hard.
 
OP
OP
FASTERDAMITT

FASTERDAMITT

Sr. Member
Joined
Nov 20, 2006
Messages
806
Loc.
Oceanside
I have the "Bullet Proof" Steering and track bar. I have done track bar mount modifications so it's only at a minimum angle, also raised the heavy duty steering on top the knuckles for clearance and less angle. so thier both even and I get no bump steer. I did the zip tie thing on the shocks every time I change anything and yes I am using almost all the travel, and would use more with ease without the bumps. However I will hit the oil pan with the top of the diff if i use less bump stop. (I've actually touched the 8 qt race pan once)
The 50 is compression and 70 is rebound. You could be correct about the needing less rebound and more compression damping.
 
OP
OP
FASTERDAMITT

FASTERDAMITT

Sr. Member
Joined
Nov 20, 2006
Messages
806
Loc.
Oceanside
I'm surprised I didn't get more Bilstein user comments... the bypass are out of my budget untill the economy improves!
 

ken75ranger

Bronco Guru
Joined
Jan 27, 2002
Messages
5,069
Loc.
Troy, NY
The 50 is compression and 70 is rebound. You could be correct about the needing less rebound and more compression damping.
It's probably pretty close to what you need. If your rig isn't real front heavy I might go to 50/80. It you have a front sway bar stay where you are.
The real difference would be adding the remote res. You're probably aerating the emulsion shock in a few seconds once you get in the whoops. That will make the shock feel like 20/40 at best. :(
 
Top