• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear Spring Removal Question

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
The time has come to replace my rear springs with the WH 3 1/2" lift springs. After a little struggling, I got the rear axle disconnected and out from under the truck. Now it's time to remove the bolts holding the springs on. They are frozen solid. I have been squirting them with PB Blaster for 2 weeks while I worked on the front. Will I have a problem if I used a cutoff wheel and cut the bolts out of there? I don't have a torch, so I am out of options. All advice is appreciated. Thanks, Mike
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Sure you can cut them off but you will still need to get the right bolts. Duff has them, WH too, prolly JBG as well. Nice new bolts will be nice.

Don't hurt your shackle or spring hangers while your cutting.
 
OP
OP
BRONCITIS74

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
Can you use grade 8 bolts, lock washers, and nuts. Looks like there are (2) 5/8 bolts and (1) 9/16 bolt.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, yes frozen bolts are a big pain. I'm guessing you have air tools, you mentioned a cutoff tool. Im guessing the nuts are off so I would bang the bolt with the biggest hammer you got, and when it starts to move put the impact wrench on the bolt head and spin it and hit it and it should break free. Good luck
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Sort of could use those grade 8 bolts....But you want them to have a shoulder a certain length and stuff...Makes the vendor's OEM copies pretty cool.
They can ship them quick since they are so small.
 
OP
OP
BRONCITIS74

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
I have an air compressor and several air tools including and impact wrench. The nuts are frozen and will not move. The only things that came off were the nuts on the U-bolts and they were a pita. Are the vendors nuts any different than a regular grade 8 bolt? I see JBG has a set for both sides for $22 + s&h. The only problem is finding the 9/16-12 bolts. They are kind of a special order. McMaster-Carr has them but the order is a package of 5.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, your 1/2 drive breaker bar gives better leverage and more power than an impact wrench. Can you get the nuts off that way? It's a start. Good luck
 

CopperRanger

Bronco Guru
Joined
Sep 26, 2007
Messages
1,796
If you have been soaking them try a 6 point socket on a breaker bar. If that doesn't work then slip on a piece of 1" black pipe over the breaker bar for a little more leverage. If you can get the nuts off then use an air chisel with a blunt end to try and drive the bolt out.
 

mtp71174

Full Member
Joined
May 8, 2007
Messages
210
The chances are when you get the nuts of you will find the bolts frozen in the sleeves in the spring eyes and shackles. I found that a air chisel with the pointed tip or hammer end will pound them out, you may need pb blast them.
 

jdbronco

Full Member
Joined
Oct 2, 2010
Messages
289
Loc.
Panama City Beach
While I have never done a head to head comparison against it, I swear by Kroil. I haven't had a stuck bolt/nut since I've used it (Knock on wood). Breaker bar and a cheater bar is the way to go.
 

Wyflyer

Bronco Guru
Joined
Apr 1, 2008
Messages
2,920
I wouldn't fight those bolts very long... I'd try a 4 1/2" angle grinder with a 5 1/2" x 1/8" cut off blade and cut them between the hanger and spring.
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
I wouldn't fight those bolts very long... I'd try a 4 1/2" angle grinder with a 5 1/2" x 1/8" cut off blade and cut them between the hanger and spring.
lol, that's what I will be doing before too long when I change out my springs. not even going to fight them much
 
OP
OP
BRONCITIS74

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
Got over on the driver side and 2 out of three nuts came off. Unfortunately it was the one at the bottom of the shackle, which would not move. This morning I ordered new bolts and shackles from JBG. I used the air chisel with a pointed tip and it drove the front bolt right out. Great idea! Thanks. The bottom bolt had to be cut off with the air grinder and cutoff wheel. The left spring is on the floor. On to the right side.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Its weird how 5 friggen fasteners a side are such a pain in the arse. A simple 3 hour job takes all weekend even if your ready for it. You will be one worn out son of a gun when your through. The 2 worst jobs. rear springs and body mounts. Seems like such a simple task until you actually have to do it.
 
Top