• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Torker 289

OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Okay so,

New filter in, timing set, (I found around 13 degrees was the best for me), and it still feels like it's missing something in second gear. . Still barely hitting the speed limit up moderate hills. Idle is around 750, no lag in throttle at all, 2 nice jets in the carb, new fuel pump. Any other ideas?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Pull off all your spark plug wires and start over. I swapped 2 plug wires one and it ran just fine. Was just a little down on power, but I didn't know it was down. One day I was checking valve lash and following the plug wires and something didn't make sense. 2 wires were swapped. It started right up, idled smooth, no popping, no sneezing, everything felt right. Didn't believe it. Marked the two wires. Went out on the lake, drove it around. Drove just fine. Swapped the wires, expected this to be a real quick test before I put it back. It ran great! The wires really were wrong.

Another time I chased a popping backfire. looked the plug wires over multiple times. One day I pulled them all off and pulled the distributor off for some reason. Went to put them back on and followed the firing order. One wire was suddenly really tight and another was really loose. Had to have done it wrong. Double checked the firing order, it was right. So I moved the wires around so they were the correct length and correct firing order. That fixed it. I had checked the firing order incorrectly before. Wasn't until I pulled all the wires off and did it again that I found the mistake. (yes I am stubborn at times)

You know there are two different firing orders for a small block? The old 302 and the new 5.0/351W. If the cam was ever changed you might have the "other" firing order. At which point you have a 4-cylinder engine which at times can run pretty good. It has been done before.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
So what are my 2 possibilities for firing order? I can't remember how I have it now. But I can see tomorrow what I have, and then maybe try the other firing order to see if it helps.
 

rmk57

Sr. Member
Joined
Feb 24, 2016
Messages
580
And a little update:

Nobody in my town sells timing tape, so I'm gonna have to order it from Amazon and wait a few days for it. Oh well. I'm sure something else will come up that needs fixing in the mean time!

Lordco should have it. I'm in the lower mainland and thats where I bought mine from.

As far as firing orders go if your Bronco runs now it wont even start with the other firing order.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Was watching a car show this evening and they brought up a stuck open pcv valve giving vacuum leak symptoms. Mine is at least 10 years old, worth replacing I figure. Any thoughts?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I ran a 289 torker on my 73 for many years well over 20, it seemed to work fairly well. Its RPM range is the same as a ebelbrock RPM manifold.
But I would not suggest using a torker manifold Single plane manifolds and heavier vehicles are not the best mix also it will require a hood scoop as its a tall intake. You will probably also run into some tuning issues as well as single plane manifolds usually require more carb tuning than dual plane manifolds.
While I never really had a complaint about the 289 torker manifold I would say its a little more cold blooded and may not be well suited to the north country. But when I swapped to a dual plane manifold I did seem to pick up a little better lowend driveability.
As was said you need to figure out whats wrong with your current setup before swapping on parts that may not solve your issues. Most likely you have timing issues Id go thru it all check the points gap check for excessive play in the dist shaft for worn bushings either can cause timing changes. Is your vacuum advance hooked up to the carb or the intake? Is the mechanical advance functioning ie will the rotor move a little then spring back when you turn it?
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
I ran a 289 torker on my 73 for many years well over 20, it seemed to work fairly well. Its RPM range is the same as a ebelbrock RPM manifold.
But I would not suggest using a torker manifold Single plane manifolds and heavier vehicles are not the best mix also it will require a hood scoop as its a tall intake. You will probably also run into some tuning issues as well as single plane manifolds usually require more carb tuning than dual plane manifolds.
While I never really had a complaint about the 289 torker manifold I would say its a little more cold blooded and may not be well suited to the north country. But when I swapped to a dual plane manifold I did seem to pick up a little better lowend driveability.
As was said you need to figure out whats wrong with your current setup before swapping on parts that may not solve your issues. Most likely you have timing issues Id go thru it all check the points gap check for excessive play in the dist shaft for worn bushings either can cause timing changes. Is your vacuum advance hooked up to the carb or the intake? Is the mechanical advance functioning ie will the rotor move a little then spring back when you turn it?

ive never checked points but it seems pretty straight forward so ill do that . vacuum advance is hooked up to the carb. stock autolite carb. it connects on the left side. Ill link a picture https://ibb.co/nfNzZH
https://ibb.co/nfNzZH

My rotor doesn't have weights so im assuming no mechanical advance and just vacuum advance? I don't know much about advance so that might be a stupid/obvious statement to some. How do I check for play in the dizzy shaft?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...Mine is at least 10 years old, worth replacing I figure. Any thoughts?

It's part of every tune-up, so after ten years (but do you know how long it's been run?) it certainly should have been replaced at least once.
You don't need to do that each and every tune-up, but after a few cleanings they say not to rely just on how it looks or rattles. At some point you just need to put a new one in.
Again though, depending on mileage/hours more than years I would think. If it's 10 years old, but only has 1000 miles on it, likely it's good. As long as it was the correct one to begin with.
Since they're cheap, it wouldn't be a bad thing to buy a new one for your specific application and keep the old one as a spare for the next time.

ive never checked points but it seems pretty straight forward so ill do that.

Well, it's not. Ok, so it is very straightforward once you've messed with them a bit, but I'd have to say there is a learning curve for the first-timer.
The typical tools needed would be:
1. Your eyes first of course, but that's just the beginning.
2. A "points file" or fine sandpaper folded over for cleaning used points. The mating surfaces of the two halves need to be smooth and clean. If they're pitted or messed up enough, they simply need to be replaced.
3. A gapping tool of some kind. Usually feeler gauges, but there are multiple types.
4. A dwell-meter is as important as a timing light. Yes, you can get it pretty close by simply adjusting the gap, but the dwell meter is basically your double-check for your gapping skills. Doesn't take much of an error in gappage to make a tidy error in dwell. Ultimately, dwell is the rating of points adjustment.
5. The timing light of course. Not points specific, but each time you manipulate the points in a distributor, you actually change the timing. Could be just a little, but can be a lot.

...vacuum advance is hooked up to the carb. stock autolite carb. it connects on the left side.

I think that's the correct fitting (the "ported" or "timed" vacuum fitting), but someone else can confirm.
The hose does look a little aged though, as do most of the bits and pieces on the engine. Might be time sooner rather than later to replace a lot of the old tired stuff. You can find yourself chasing tails when old parts are left in service.

My rotor doesn't have weights so im assuming no mechanical advance and just vacuum advance?
I don't know much about advance so that might be a stupid/obvious statement to some. How do I check for play in the dizzy shaft?

That's actually a good point to make. You might be thinking of the old GM distributors where the weights were conveniently mounted on top of everything else, right in plain sight.
The Ford distributor's weights are beneath the points plate, so you can't see them. But if you can turn the rotor by hand a few degrees smoothly and have it spring back all the way, with very little to no slop, you have mechanical advance weights in place.

For checking play, there are to dimensions in question usually. Aside from the movement you get from the advance mechanism(s) you can push and pull the shaft sideways to determine if the bushings/bearings are worn. There really should not be much (if any) perceptible play in the sideways direction.
Next you have up and down play. There is a specification for that, but I don't remember what it is. Someone can post up the info, but here again it's not a lot. If you have more than 1/8" up and down movement we should make sure that's normal. Been awhile since I wore out a distributor, and now my driver doesn't even have one!;D
Sorry I can't remember all the stuff, but that's why we're all a team here. Someone's always coming up behind to take the baton and run with it!

Good luck. Should be able to get it running like a top once you go down the list, read all the proper books on how to do this stuff (unless you've done some of this kind of thing on other types of engines already) and you'll get the basics down.

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Yeah it's definitely a little tired for sure. When it was purchased about 10 years ago, it was the guys daily driver. It was bought, driven by my dad for a while, then parked in the back yard. It ran great when it was parked, and now it just seems I'm chasing a whole bunch of weird stuff. I guess that's all part of the adventure with something 48 years old. I've come to embrace it. As per most nights, I'm heading into tomorrow with a whole bunch of new stuff to try, so thanks guys!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Glad you're able to embrace the experience. Otherwise you'd be embracing a bottle and looking for hair implants from pulling yours out!;D

It's pretty typical of any vehicle (but way more so on older ones) that has sat around for awhile after having been driven.
If it's put away brand new, a few things still will age in place. But if it's driven first, then sits, a whole LOT of things need replacing just from the age. Fuel pumps come to mind.

Anyway, we look forward to following along on the adventure.

Paul
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
This may help your tune up some.

http://www.tpocr.com/ford1.html

As far as points go don't set them a tight .017 unless you like setting points all the time. Aim more for a slide in feeler gauge and no tension at all. If your using a dwell meter set the points on the high side. The rubbing block wears down and closes the point gap so the longer you delay that the better. You also need a thin film of grease on the point cam on the distributor shaft. And don't forget to pull up the rotor and put a drop of motor oil down the hole under the rotor. There is a felt wick in there to hold the oil and lube the advance mechanism shaft. Just a drop not a gusher.

The vacuum advance on the distributor. Put a piece of hose on it and suck on the hose and make sure it actually holds vacuum. All of them are beyond in years and can fail any time. Even new ones in the auto parts have been sitting in there forever.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
pulled the dizzy today. not sure how springy the rotor return is supposed to be, but it wasn't very springy . quite slow actually. Cleaned the points and set them to 0.018. I had what i think was normal up and down play in the shaft . very minimal side to side play in the shaft. Gonna put it back in and see where we're at. I think I'm also gonna take the carb off and rebuild it. From what i've read, incorrect float levels can cause the lack of power issue im experiencing. Worth a shot anyways, and the carb could probably use some love.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
pulled the dizzy today. not sure how springy the rotor return is supposed to be, but it wasn't very springy.

Were you checking while holding the shaft still? Normally that spring test is done with the distributor still installed so that the meshing gears will hold the shaft still.
There is gear lash play of course, but that's not very much at all. But the springy thingy shaft check is for the separate advance mechanism. It's basically a separate shaft that rides on top of the main shaft and holds the "points cam" along with the weights and springs. The other end of the spring is attached to the main shaft, so that when the weights spread out at higher speeds, they're literally twisting the two shafts separately.
This way the main shaft stays in time with the engine/camshaft, and the upper advance shaft spins to advance or retard the actual trigger event.
Used a lot of words because I really can't explain how it feels. Just that you will need to hold the shaft still from the bottom while you twist the top piece.

quite slow actually.

If it's actually slow, then it's gummed up from years of use and can maybe still be pulled apart and cleaned and re-lubed.
Sometimes just a good dousing of Chemtool (carb cleaner) and then a good dousing of WD40 or something will clean and lube it for good effect.
A buddy used to use both of those as his normal maintenance during tune-ups. Had the cleanest, best functioning old distributors of anyone I knew! I don't think he ever had to replace one. Just kept it cleaned and lubed about every 5k to 10k miles, and that was it.

Cleaned the points and set them to 0.018. I had what i think was normal up and down play in the shaft.

Like maybe in the thousandths of an inch? Or maybe a 1/16" to 1/8" or so? Or more like 1/4 inch? That last would be too much in my opinion. But I forget the spec. Easy enough to find though.

very minimal side to side play in the shaft.

Would have to be, since it's in bushings and should have almost zero perceptable play to be good. Of course, even a little does not mean the early death of the distributor. Just that it might not keep as consistent a time with points as a very tight one would.

From what i've read, incorrect float levels can cause the lack of power issue im experiencing. Worth a shot anyways, and the carb could probably use some love.

Never really experienced that myself. But like you said, worth a shot. They always need some love.

Paul
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Dont rebuild the carb until you verify the spark issue is resolved. fix one problem at a time and verify the problem is revolved. a shot gun approach might feel better but how can you tune a carb if the ignition isn't working properly.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
My experience with the advance springs being slow was while the distributor was still in the engine. I'll try and lube it up and see if I can't get a little more response from the springs. Thanks guys. I'm gonna hold off on the carb rebuild until I have the dizzy back in and the truck is running at least as well as it was before I pulled it out.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Wont hurt to rebuild/clean the carb but for the most part I doubt its your issue. the stock carb has its jets on the bottom of the fuel bowl so even if float level is low it really wont affect the fuel metering. But a bad power valve can cause all kinds of funky issues if the diaphragm has hardened up it may not be functioning as intended and could be the cause of the lack of power.
The main issue with shot-gunning issues is you may not figure out exactly what part was causing the problem so one at a time can help pinpoint the problem.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Pulled out the points and condenser, tried to clean them up and make them work, but I think a lack of understanding really got in my way. Got myself a pertronix igniter system, and the truck fired right up. However! (There always seems to be a "however" when i work on this thing lol), the breaker plate is awfully loose making the igniter module bounce around and throw my gap way off, which in turn throws my timing way off... I wonder if I missed something putting it back together. Oh well. Hopefully I can get it secured as it should be. If not, I wonder if a new breaker plate would come with the necessary hardware that I more than likely lost, or if I would need a new dizzy all together. Only time will tell I suppose.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, when you install points and condenser or Pertronix you don't have to remove the breaker plate, so I'm kinda lost.
Did you really undo the C clips and get the breaker plate and nylon bushings out? That takes a lot of work.
The arm from the vacuum advance canister pretty much hold the breaker plate in place.
Does the breaker plate just slide back and forth, or rock all over like it is tipsy?
Usually wear in the distributor is because the shaft and bushings are worn.
Good luck
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
No I didn't take out the breaker plate. Where the arm connects to the breaker plate, it is very loose and the arm can move around in the hole on the plate. I will post a video and post the link here for you to see.
 
Top