• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Transmission & transfer case question

SuperSession74

Jr. Member
Joined
Sep 20, 2016
Messages
60
Loc.
Redondo Beach
Anyone have any experience with the 3 speed w/overdrive or the 4speed " imposter" RUG T&C Tranny ? There is one for sale in my area that has been rebuilt it looks to be from a 78 f150 looks like the cast iron version not the Alum case top shift version or the SROD version. Does this require a special 4speed shift linkage or adapter or does a regular 4speed top loader work? New to the EB's but not old Fords have a 64 Galaxie and a 64 Country Sedan just picked up a 74 Sport with a 351 and stock 3pd on the floor 33" tires pretty sure stock gearing. Thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I think just a few of them installed over the years. Was thought to be at least a decent option back before better transmissions became available, but never really caught on.
Probably due to the strange ratios and, back then at least, most EB owners wanting a lower first gear for off-roading.
Never heard anything bad about them. Just that not many have utilized them.

At least that's for the general type. Not familiar with the different styles of shifters. I thought they were all SROD motels, so you can see how limited my knowledge is about them.

Congrats on the new '74. Cool that is has a 351 too, as long as it's running well and not subject to overheating, like some have been.

On an Early Bronco, your "stock" gearing could have been either the 3.50 or the 4.11 setup in the rear. Even 4.56's were available some years (with 6-cylinder engines), but don't think that was still an option by '74.
If you have the 3.50's, then the extra torque of the 351 would be a BIG benefit with the 33 inch tires. The 4.11 is better suited to the Bronco's weight and aerodynamics, but depends on what you're going to do with the truck.

If you are going to try to fit an overdrive in there, then hopefully you have the 4.11's or most likely you won't be using overdrive very often.;);D

Paul
 

SuperSession74

Jr. Member
Joined
Sep 20, 2016
Messages
60
Loc.
Redondo Beach
Thanks Paul yes mechanicaly it runs strong recently rebuilt. The 3speed is doing a little 2cnd gear dance little grind and wants to pop out when downshifting. That was when i started thinking about the 4speed od. The version i was looking into is the ' SMOD ' side mounted shifter like a 4speed TL as opposed to the 'SROD' single rail shifter tube style i believe those are pretty worthless for the EB. As for overheating runs cool nothing like my dads long gone Ranchero with the 351 Cleveland . Thanks really digging the Bronc been hunting for a while. Also thinking a C4 easier for the wife and my knees ! Not gonna be doing any serious off roading more of a Beach/Surf cruiser . Although towing with my RV also factors in on keeping it manual.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
The way I see it, even if you never used the 5th gear, a NV3550 would be worth swapping in with 3.50 differential gears.
The 1st, 2nd, and 3rd gears of a NV3550 are just better suited for our cars than the factory three speeds.
Gear NV 3550 Stock 3 spd

NV3550 vs Stock
1st 4.01...2.99
2nd 2.32...1.77
3rd 1.40...1.00
4th 1.00
5th 0.78
Reverse 3.57
 

Joe473

Sr. Member
Joined
Jul 16, 2012
Messages
958
M5R2 is similar ratios. Link also has info on "RUG" 3+1 overdrives. I swapped one behind an '85 stepside 300 that was three on the tree 20+ years ago Very similar to the 3 speed ratios and the 300 had the torque to pull 31's with 3.27 gears in OD.

I have the M5R2 in the bronco right now and it's a much better option then the 4 spd OD.

http://www.blueovaltrucks.com/tech/transmissions_manual.htm

Sent from my SM-G900V using Tapatalk
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
M5R2 is similar ratios. Link also has info on "RUG" 3+1 overdrives. I swapped one behind an '85 stepside 300 that was three on the tree 20+ years ago Very similar to the 3 speed ratios and the 300 had the torque to pull 31's with 3.27 gears in OD.

I have the M5R2 in the bronco right now and it's a much better option then the 4 spd OD.

http://www.blueovaltrucks.com/tech/transmissions_manual.htm

Sent from my SM-G900V using Tapatalk

The early Borg Warner T-19 looks like it might be a good option for someone wanting to keep their 3:50 gears and get better gear selection. It has all synchronized gears, and the first gear is actually a real first gear and not a "granny low."
The only question is, will it mate up to a Dana 20 transfer case?
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
The early Borg Warner T-19 looks like it might be a good option for someone wanting to keep their 3:50 gears and get better gear selection. It has all synchronized gears, and the first gear is actually a real first gear and not a "granny low."
The only question is, will it mate up to a Dana 20 transfer case?

The narrow range T-19 was mostly used in diesel engined trucks, like the bread trucks with the 4BT Cummins.

The 4x4 trucks with 460 engines had a T-19 with a 6.32 first gear.
 

Nothing Special

Sr. Member
Joined
Nov 25, 2016
Messages
848
I have 33" tires and 4.10 gears in my Bronco. I went from the stock 3 speed to an NV3550. I also went to an Atlas transfer case, but one of my main goals was to get a lot better crawl ratio, so the Atlas was decided on before the trans in my case.

Adapting the NV3550 to the 302 wasn't a big deal. I bought the adapter plate and clutch disk as a package. There was a little cutting and filing required, but it was all spelled out in the instructions and went pretty easily. The Atlas bolts right to the NV3550 (which was part of why I picked the NV3550).

I really like the gearing I have now with the 5 speed, 4.10s and 33s. On road I might prefer 3.55 gears. Right now I never use 1st gear (unless towing a trailer), and I could use a little taller gearing cruising on the highway. But it's pretty good on-road, and the 4.10s are better when towing or when 'wheeling.

I threw out the ZF5 as an option because it was bigger and heavier than I wanted and would need to have a hydraulic clutch linkage. And while it would bolt right to the engine it would need to be adapted to the Atlas. By the way, if you do go with a ZF5 make sure you get one from a small block (or 300 six). They have integral bellhousings and the big block or diesel trannies won't bolt to your engine. And I'm pretty sure the NP205 won't just bolt up to a ZF5. It might not be hard to adapt, but it does take some additional effort.

The Mazda M5OD-R2 from F-150s is more the right weight, but again required a hydraulic clutch and would need an adapter to the Atlas.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
An Atlas will bolt directly to a ZF without any adaptors. Just need to order the Atlas with the 31 spline Ford input and be sure you get a 4WD ZF.

The NV3500 series transmission is completely different then the 4500 series transmissions. The 4500s are heavy duty truck transmissions. Granny low first, a 3-speed worth of gears in the middle, and an overdrive up top. Wide ratio spread. Drives like the old 3-speed with an extra gear on either end.
The NV3500 family is pretty much street (car) gear spacing. Lot closer ratios. First is 4:1 where the 4500 is over 5.5:1
 

Nothing Special

Sr. Member
Joined
Nov 25, 2016
Messages
848
An Atlas will bolt directly to a ZF without any adaptors. Just need to order the Atlas with the 31 spline Ford input and be sure you get a 4WD ZF.

I'm not saying you're wrong, but that wasn't what I was told (I think by Advance Adapters) when I was researching it.

The NV3500 series transmission is completely different then the 4500 series transmissions. The 4500s are heavy duty truck transmissions. Granny low first, a 3-speed worth of gears in the middle, and an overdrive up top. Wide ratio spread. Drives like the old 3-speed with an extra gear on either end.
The NV3500 family is pretty much street (car) gear spacing. Lot closer ratios. First is 4:1 where the 4500 is over 5.5:1

I agree with all of that, but be careful with the NV3500 / NV3550 names. They are essentially the same transmission but the NV3500 has an integral (Chevy) belhousing while the NV3550 (used in Jeeps) has a detachable bell. It's the Jeep trans that you can easily adapt to a Ford bellhousing
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
I threw out the ZF5 as an option because it was bigger and heavier than I wanted and would need to have a hydraulic clutch linkage. And while it would bolt right to the engine it would need to be adapted to the Atlas. By the way, if you do go with a ZF5 make sure you get one from a small block (or 300 six). They have integral bellhousings and the big block or diesel trannies won't bolt to your engine. And I'm pretty sure the NP205 won't just bolt up to a ZF5. It might not be hard to adapt, but it does take some additional effort.

The Mazda M5OD-R2 from F-150s is more the right weight, but again required a hydraulic clutch and would need an adapter to the Atlas.

The ZF5 and M5OD both bolt on the NP205 only requiring a notch in the flange for the transfer case shifter rails. They have the standard Ford 6 hole mounting ring as does the Ford NP205.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
An Atlas will bolt directly to a ZF without any adaptors. Just need to order the Atlas with the 31 spline Ford input and be sure you get a 4WD ZF.

I'm not saying you're wrong, but that wasn't what I was told (I think by Advance Adapters) when I was researching it.

It's a direct bolt up, just like the 4WD 4R70w is. If you read through A/A's tech vault, you'll see.

Mark
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...Although towing with my RV also factors in on keeping it manual.

Not saying it can't be done, but EB's are likely one of the poorest towing vehicles out there, right out of the box anyway.
A few things you need to do to make them more tow-friendly, but trans choice doesn't really seem to be a stumbling block. Primarily it's the transfer case you worry about if I remember.
So C4 or AOD or 4R70W or whatever, and you can keep the wife and kids happy with the auto. I personally think manuals are fun to run around with too, in an old rig like a Bronco. You might find your wife feels the same way after bopping around in it for awhile.
But if not, autos are certainly more around town friendly.

Towing is just another beast altogether. Very much worth reading through the towing threads here on the forums. There was a good one just in the last month or two if I remember. The search tab above "might" come up with what you need, but better still is a Google search with the suffix "classicbroncos.com" either in quotes, brackets or whatever the proper clever little bits are for that. I've used quotation marks to good effect several times.

Good luck!


Quick question to all, is the NV3550 better then theNV4500? If so what are the advantages or disadvantages?

What they said already...
But I'd add too that the 3550 with adapters and D20 is virtually the same length as the stock setup. Maybe less than an inch difference. So your driveshaft lengths don't need to be changed at all.
A nice monetary bonus!

That along with it's much smaller bulk just makes it a much easier install in an EB.
And as said, even though many of us like wide ratio truck trannies with grannies, the 3550 gear ratios are very street friendly.

Paul
 

Nothing Special

Sr. Member
Joined
Nov 25, 2016
Messages
848
The ZF5 and M5OD both bolt on the NP205 only requiring a notch in the flange for the transfer case shifter rails. They have the standard Ford 6 hole mounting ring as does the Ford NP205.

If I'm wrong on this it certainly wouldn't be the first time, but my understanding was that all of the aluminum or magnesium Ford transfer cases have the same standard input and will attach to all of the same transmissions. Since the ZF5 and Mazda trans were from that era all of the "alloy" cases will work (13-45, 44-07, 208, others?). But that the older iron cases like the 205 were a different standard and wouldn't interchange.

But if my info was wrong then so am I.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
If I'm wrong on this it certainly wouldn't be the first time, but my understanding was that all of the aluminum or magnesium Ford transfer cases have the same standard input and will attach to all of the same transmissions. Since the ZF5 and Mazda trans were from that era all of the "alloy" cases will work (13-45, 44-07, 208, others?). But that the older iron cases like the 205 were a different standard and wouldn't interchange.

But if my info was wrong then so am I.

The Ford NP205 was one of the first if not the first with the six holes in that size of a circle mounting.
The alloy cases (and the NP203) followed it.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
The old 205 rear shift for will interfere with the new 6-bolt flange. That is why you have to notch the flange.

The old stuff ran longer adaptor housings because the transfer case was more compact. After '80 the transfer case got longer (Planetary gears in front of the chain reduction and typically a slip yoke) the adaptors got shorter.

So stuff did change. But they still have the big 6-bolt transfer case mounting circle and 31 spline spud shaft.
The Bronco got the small 6-bolt circle and 28 spline.

There were a few oddball exceptions. Dana 21 single speed transfer case comes to mind. But the common NP203/205 married transfer case from the (later) 70's can be mated to the stuff from the 80's and most of the 90's so long as it is full size. Ranger/BroncoII are completely different at 25 spline and 5-bolt flange. Explorer is the small stuff unless you find the V8, which is the big stuff.
 
OP
OP
S

Sutcavage

New Member
Joined
Jan 2, 2017
Messages
19
Loc.
Raleigh
Ha!
I was going to invite you to drive mine.
I figured you lived somewhere between Salem and Winston Oregon.
I never knew there was a city with that name.?:?

Hahaha I appreciate that. Oh yeah, it is estimated that one in three cigarettes sold in the country were manufactured by R.J. Reynolds Tobacco Company, here in Winston-Salem. That's about all I can think of off the top of my head.
 
OP
OP
S

Sutcavage

New Member
Joined
Jan 2, 2017
Messages
19
Loc.
Raleigh
You might find the mazda m5od trans more affordable. They are in f150 trucks from about 87 to now. Ones equipped with 300 6's and 302's. After the mod motors it would be the v-6 models. The newer the trans the better the internals. Also the newest version has the shifter farther back in a better location. You will need the zf d-20 adapter and a twin stick to make it all work. Oh and a custom crossmember and the throwout bearing and hydraulic clut h out of the same truck. Bronco flywheel will work though

Whoa I had no idea. Thanks
 
Top