• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Vacuum Reading & Troubleshooting

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
My 1977 Bronco has recently been having a rough idle so I have taken the following steps:

1. Added Sea Foam (no crazy smoking)
2. Oil Change and Filter Change
3. Checked fuel filter - doesn't seem clogged
4. Adjusted carburetor - I increased the idle RPM and adjusted air/fuel mixture so idle was not as rough; idle in park is around 700 RPM.

I've attached the vacuum gauge to the full vacuum advance on the carb and on the tree port behind the carb. I'm trying to learn as I go but I think the second connection is the right place to connect the vacuum gauge. As you can see on the pictures, the gauge settles at 14 inches for both port locations. The gauge will jump up into the green (43 - 55) when I hit the throttle but then settles back around 14.

Question 1: Are these good hookup locations for the vacuum gauge?
Question 2: Obviously, the steady 14 in. reading is not optimal. I've been using this website to figure out what the readings mean but I am still unsure what the issue could be. I can try to upload a video if that helps. Any ideas what could be wrong and/or what is needed to fix the problem?

Any insight you can provide will be very helpful. Thanks!
 

Attachments

  • gauge-from-carb.jpg
    gauge-from-carb.jpg
    90 KB · Views: 217
  • gauge-from-port-tree.jpg
    gauge-from-port-tree.jpg
    92.7 KB · Views: 262

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Do you have a vaccum booster for power brakes ?
An internal leak can cause a bad idle and an inconsistent idle
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Hook the vacuum guage to the vacuum tree behind the carb.

Timing will effect the heigth of the steady idle vacuum reading. Try 12 degrees advance. Vacuum at distributor vacuum should have little to no vacuum at idle on a stock carb and advance port. If you have a dual port advance distributor the port closes to the cap will have manifold vacuum but it is used for advance retard function not for vacuum advance on the engine. If you love your Bronco get rid of that POS air cleaner before it burns your Bronco to the ground. One backfire through the carb catches the oiled foam on fire. I have personaly seen this happen on more than one occaision
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
A reading of 14 is low for any stock-ish engine. Even a mile performance engine should be able to get up into the 18 range. But much more performance than stock and 16 comes quickly. But 14 is about where you'd expect a pretty big cam with a lopey idle to read.

The vacuum tree, while a good spot to get a quick reading, is usually connected to a single cylinder runner. So it's getting it's signal mainly from that one cylinder.
I think the common plenum area under the carburetor is the better spot to check overall engine health.
Obviously you're getting similar readings so it's not that bad. I'd maybe use the tree for tuning, but use the common area while trying to find and diagnose a problem.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And at this point too, I'd be looking for vacuum leaks first. Spray some brake cleaner spray around the various areas of the engine to see if the idle changes.
If you're not sure about the relative intelligence of spraying flammable gasses around the compartment;D you can use WD40 or even water in a spray bottle to do the same thing.
I've always used good old Berryman's Chemtool carb cleaner (because I have it handy) but would not recommend it if your paint is new on the engine.
If the paint is original and has been curing for 40+ years, it's not as big a deal. And brake cleaner evaporates so much quicker, it's even safer on paint than carb spray is.

But you're basically looking for anything that can make the engine idle rough. On an original engine you'll be lucky if it's vacuum leaks (very common on any engine) and not something more sinister and dire, such as valve seats leaking, or other internal old-age issues.

Good luck!

Paul
 

triracer67

Contributor
Sr. Member
Joined
Nov 29, 2010
Messages
672
I was taught to adjust my timing base on manifold vacuum, turn to max. vacuum, and retard a degree. I will check the timing with timing light afterwards to make sure it's within bounds. I do have to say I have zero issues with my motor starting, or running.
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
I did the old soapy water test around the headers and I saw a lot of bubbling going on which makes me feel like I need to replace the gaskets. Am I able to unscrew the headers and install the new gaskets without completely removing the headers from the exhaust/truck?
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
I did the old soapy water test around the headers and I saw a lot of bubbling going on which makes me feel like I need to replace the gaskets. Am I able to unscrew the headers and install the new gaskets without completely removing the headers from the exhaust/truck?

On second thought, I did it again when the headers were a little cooler and I didn’t get all the bubbling that I thought was going to be leaks from the header. I actually think it might be the water evaporating and boiling on the hot surface.

%)

Whoops.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yes, sometimes.

Assuming there is no residue that you can't get off with the headers in the way, all you need to do is remove all the bolts, slide the old gaskets out, slide the new ones in, replace all the bolts and torque to spec. Done (theoretically)...

Some gaskets actually have that slotted affair on the outside two bolts so that you can leave the outermost bolts in place and still slide the gaskets into place. I don't know if any of the gaskets do it for our Fords, but even if not, with the headers still connected to the exhaust it's not like they're going to go anywhere when you remove the bolts. They'll be held in place by the rest of the exhaust system, not to mention all the crap that's in the way of them going anywhere in a Bronco engine compartment!

Just curious... With soapy water and an exhaust manifold, how do you know it's bubbling up from air escaping, and not just boiling from the heat?
I'm guessing you can tell the difference in at least most cases, but I wonder at what heat level the water and soap start acting at least a little like an air leak?

Good luck.

Paul
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
I'm stuck at home today with a kid who has strep (yay) so I am going to dedicate some of today to figure this out.

After my "soapy water boiling" whoopsy, I adjusted the air/fuel mixture on the carb and have the in-park RPMs set at 700.

The port tree on the back of the intake manifold is connected to the brake booster and the transmission (I think?).

The timed vacuum on the carb (Edelbrock 1403 - left port) is connected to the distributor. The PCV is connected to the manifold. The power brake port on the back of the carb has been plugged.

Crazy question: Shouldn't the brake booster be connected to the carb's power brake port? Or does it not matter?

Also, I have carb cleaner (Gumout); I suppose that is fine to use around the engine/manifold to check for leaks (paint issues aside)?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
No, the brake booster is fine in either location. Most factory setups use the tree, or at least a single port on an individual runner. So no problem there.
If you ever have one connected to the base of the carb, it would be fine too as long as it's not using the only port available, which should be dedicated to the PCV.

Yep, Gumout is a great "vacuum leak tester" formula.;D
And it cleans the carb as you test too, in situations where the carb is dirty from use. The choke linkage is a great bit to keep clean too. After cleaning the choke linkage I usually spray some light lubricant too, in order to let it work the best. If it's "too clean" and dry, some of the gravity-activated components can stick.

Paul
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
And at this point too, I'd be looking for vacuum leaks first. Spray some brake cleaner spray around the various areas of the engine to see if the idle changes.

I just sprayed around the engine and the idle did increase when I sprayed the tree port. I’m going to try to gently tighten up those parts and continue to troubleshoot.

I also bought a timing light so I’m gonna give that a shot as well.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Careful tightening that tree you may crack the intake manifold! I would start by taking all the hoses off the plugging the ports then trying your test again. See if it is the tree or intake in the area.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yeah, what Mark said.
While not unheard of for the tree to crack, it's more likely a hose or cap has failed. If you have any ports covered with vacuum caps, those are notorious for drying out and cracking.
If one of the hoses has swollen up, a clamp should fix that, or you can replace the hose.

But if it's the tree, see what it needs before tightening. Maybe it's just loose and that will fix the leak, or maybe it's damaged and the last thing you want to do is break it off in the intake manifold!

Paul
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
^^^^ be very careful

BTW sounds/looks like a vacuum leak.

Are you able to get vacuum up by moving timing?
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
I tightened the tree like two porcupines having sex: very carefully.

The gentle tightening did help; I sprayed with carb cleaner again and the engine didn't rev like it did before. The plugs on the tree are relatively new so I do not think that was causing an issue. I also tightened up the rear carb port just in case. The vacuum gauge did improve to 15 inches so I am heading in the right direction.

I appreciate all of the help and feedback.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hey, some good results! Hope they keep coming fast and furious until you're spot on and running smooth.

Paul
 
OP
OP
bostonbronconut

bostonbronconut

Contributor
Question Asker
Joined
Jul 17, 2018
Messages
198
Loc.
Wayland, MA
All of the adjustments I've been making have been done in my garage so I decided to drive the Bronco to work today, which is about an 8.5-mile trip. Two things stood out to me:

1. Vibration When Stopped - As mentioned on my original post, I adjusted the carb to fix a rough idle issue. I have the Parked RPMs set at 800. When I put the truck in Drive, the RPMs drop to around 400-500 and the car begins to vibrate, specifically on the driverside. It vibrates so much that if I hum, you can hear the vibrations in the sounds I make (my daughter thought that was hilarious). The vibrations stop when I put the truck back in park and/or when I apply pressure to the gas pedal.

2. Ticking/Flicking Sound During Idle & Acceleration - From the driverside of the engine compartment, there is a ticking/flicking sound that occurs during idle and acceleration; it does not happen when cruising (or at least it is not audible during cruising). I tried recording a video of said sound but it isn't easy to detect due to wind noise. I'll do another recording at the end of the workday.

I do not know/think that the two above issues are related but it does seem like a coincidence - nor do I know if this is a vacuum issue as well.

Any input is appreciated.
 
Last edited:
Top