What have you done to your Bronco today?

[tasker]

MIGS makes a nice rear end!

 

[sprdv1]

a man of action...

BROKEN no more thanks to a bevy of my Bronco friends! Bax for the replacement Detroit....Artemis for the ring and pinion....and MOST importantly Migs for his outstanding attention to detail in appearance and assembly! I could not of done this in a thousand lifetimes and he is THE MAN!!! Hopefully install this weekend and crusie next weekend...fingers crossed!

 

[Cortez]

MIGS makes a nice rear end!

Baby got back!;D

 

[romegadave]

Installed a new fuel pump and working on some leaks

 

[sriha]

Thought I was getting close to being done but once the transmission was in and filled it didn't want to shift into 3rd. Should have probably had it rebuilt before installing. The only thing not connected is the kickdown cable. Transfer case seems to work in high and low, will probably go the twin stick route. Seems to be cheaper than buying a new single lever since I have misplaced mine. While out test driving the steering rod or track bar got caught on the front axle and I was stuck turning right until I muscled it over. Bushings are shot so more work on top of pulling the tranny again. At this point I almost rather trailer it to a shop and have someone else take it out but my wallet will say otherwise.

 

[WILDHORSES]

Finished plating Mitch's frame where the trac bar bracket was breaking off.

Wiring Sheyla's Spal fan.

 

[Ol'Blue]

Finally finished floor pan replacement and inner fender rust repair.

And if anyone can tell me how to get the picture straight, I would appreciate it. Just started posting this way. Thanks,

 

[jmhend]

They look straight on my phone.

Sent from my SM-N960U using Tapatalk

 

[Redneck72Bronco]

I rebuilt my Dana 44; put in an ARB locker and disc brakes. I also did the Ford 9" with the ARB locker and the Tom's Bronco Parts rear disc conversion. Can't wait to put them under the truck!

 

[Audifan]

Technically "I" didn't do it, but it is my Bronco, and we did a bit more paint stripping today on the exterior

 

[sprdv1]

Nice work..

I rebuilt my Dana 44; put in an ARB locker and disc brakes. I also did the Ford 9" with the ARB locker and the Tom's Bronco Parts rear disc conversion. Can't wait to put them under the truck!

 

[Cortez]

Got the transmission reinstalled after troubleshooting a noise between my tcase and transmission. Turned out to be a bolt from my tcase adapter protruding into the NP435 case and touching the reverse gear which sets right next to the bolt hole. Had my bride helping...took a few cuss words to get the tranny properly aligned but that’s how it usually goes.

 

[kylakekevin]

Went to a local cruise nite and ran into another bronco owner

 

[Calibronc66]

Might have open a can of worms wanted to replace the core support ended up both inner fenders and a little more.

Sent from my iPhone using Tapatalk

 

[JefeAZ]

Put 10 miles on it Saturday. More than its seen in 5 years!

Also flexed a little bit!

Video: https://www.youtube.com/watch?v=SBz5hXzSRAo

It tucks!! Front sway bar connected

 

[sprdv1]

Livin large for sure.. that thing gets better looking every time I see it

Put 10 miles on it Saturday. More than its seen in 5 years!

 

[JefeAZ]

Livin large for sure.. that thing gets better looking every time I see it

haha thanks! Its still filthy too. Detailer comes out in a month, the day before my first car show. Its going to look insane

 

[Howard2x4x4]

haha thanks! Its still filthy too. Detailer comes out in a month, the day before my first car show. Its going to look insane

I suspect you'd better start clearing a space for some hardware...…..

 

[sprdv1]

haha thanks! Its still filthy too. Detailer comes out in a month, the day before my first car show. Its going to look insane

I can imagine a lot of head turns and a few trophies

 

[jmhend]

Combining three days here.

Installed a new water pump, fuel pump, fuel filter, alternator and heater hoses.


Sent from my SM-N960U using Tapatalk