• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Why does she wander? Braking issues.

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
All is great coasting or accelerating. Very well behaved on the twisties and highway speeds. No death wobble. No shimmy.

But...brake hard at any speed - especially above 30 mph - and she wanders all over the road. Tough to keep in a straight line. Damn scary.

Just starting to try and diagnose this, but advice is always appreciated. Is it possible I'm getting variable hydraulic pressure at the brake cylinders? Uneven brake pad wear? Front (disc) look pretty even, but haven't yet pulled the rear (drums) to check.

Got a tight solid heim setup and all front linkage checks out. No wiggle.

I know the nature of the short wheelbase, front heavy beast - not exactly gonna track like a Brembo 4 disc Mustang - but I'd sure like to keep her in my lane when I'm coming around a corner and facing an 18 wheeler - or a loose cow - on a mountain road. Yes, it has happened!
 

rjlougee

Bronco Guru
Joined
Dec 26, 2001
Messages
1,959
1. How is the alignment? If out of spec it will go anyplace...

2. Track bar bushings: Same as above.

3. Tire pressure balance. Hard to believe, but significantly different pressure side to side can also cause this and other issues.
Joe
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
1. How is the alignment? If out of spec it will go anyplace...

2. Track bar bushings: Same as above.

3. Tire pressure balance. Hard to believe, but significantly different pressure side to side can also cause this and other issues.
Joe

Joe,
I'm pretty confident the alignment and bushings are good - but this is exactly the kind of info I'm hoping to get. I'll put them on my list of things to check. But first the tire pressure. Gotta start there!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Random wander or predictable ( same way every time)?

Bushings come to mind first. Track bar angle and side shift from loading front suspension.

Maybe enough brake torque to wrench the axle into bad negative caster?
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
Random wander or predictable ( same way every time)?

Bushings come to mind first. Track bar angle and side shift from loading front suspension.

Maybe enough brake torque to wrench the axle into bad negative caster?

I'll take her out tomorrow to see if it's the same or variable wander. Either way...adding these to the list.

Any way to check these things without having to trust a local alignment shop?
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
1. How is the alignment? If out of spec it will go anyplace...

2. Track bar bushings: Same as above.

3. Tire pressure balance. Hard to believe, but significantly different pressure side to side can also cause this and other issues.
Joe
X2, where you been Joe haven't see ya around in a while
 

firewalker73

New Member
Joined
May 17, 2015
Messages
32
I'll take her out tomorrow to see if it's the same or variable wander. Either way...adding these to the list.



Any way to check these things without having to trust a local alignment shop?



Make sure to note the road surface when seeing if the concern is variable. If the road has depressions in it, it will wonder when braking. Try to be on as flat as surface as possible to determine if it is a vehicle concern or road surface concern. Also check that all of your shocks are good. If everything checks out good you may want to install a sway bar.



Sent from my iPad using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If the tire pressures check out, you can even add rotating the tires to your list of things to try. Sometimes you get an oddball tire that can do that even if it looks good on the outside.
Are these older tires by any chance?

Just like the tires and the brakes, something wrong with the wheel bearings can do this as well.
And yes, it's possible to have different pressures at each brake. This might be caused by a deteriorated rubber hose at the brakes, or a rusted up hard line crossing over from the center.
Because it's pulling to one side, it's nothing to do with anything hydraulic from the junction point on top of the axle, all the way back to the master cylinder. If it was something more upstream, it would effect both left and right equally. So if it's brake related, it's got to be in one of the sides.

When it pulls, do you feel it in the steering wheel at all, or does it just wander without physical feedback into the wheel?

Even though you have a few things to check, when it comes to Broncos and drum brakes, the first thing I suspect is the brakes themselves.

Best of luck!

Paul
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
If the tire pressures check out, you can even add rotating the tires to your list of things to try. Sometimes you get an oddball tire that can do that even if it looks good on the outside.
Are these older tires by any chance?

Just like the tires and the brakes, something wrong with the wheel bearings can do this as well.
And yes, it's possible to have different pressures at each brake. This might be caused by a deteriorated rubber hose at the brakes, or a rusted up hard line crossing over from the center.
Because it's pulling to one side, it's nothing to do with anything hydraulic from the junction point on top of the axle, all the way back to the master cylinder. If it was something more upstream, it would effect both left and right equally. So if it's brake related, it's got to be in one of the sides.

When it pulls, do you feel it in the steering wheel at all, or does it just wander without physical feedback into the wheel?

Even though you have a few things to check, when it comes to Broncos and drum brakes, the first thing I suspect is the brakes themselves.

Best of luck!

Paul


Thanks Paul,

I'll get her out on the road and check some things out today after work. Brand new tires. But I'll start by checking tire pressures.

I did pay close attention to the road surface I was testing this on yesterday. I actually went right down the middle of the road. No major bumps or divots or anything like that. I can distribute this to Road issues.

But I do appreciate that everybody here is giving me a good place to start.

Tony
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, of you have a digital temp gun you can compare the rotor and drum temps. They should be very close side to side after a bit of driving. Good luck
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I would check the doughnuts on the end of the track bars and the spring and shackle bushings in the rear. I would put the truck up on jack stands and transmission in neutral and with someone lightly applying the brake. spin the tire by hand and make sure the brakes are dragging at all wheels and are fully releasing when you lift off the brake. Then mash the brake and make sure all wheels are properly locking up.
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
Well I've got some more info. I figured something out.

She pulls to the right every time. The back right brake is locking up. Doesn't require a lot of pressure. It's the only wheel that locks up with light pressure. Even at slow speeds if I hit the brakes I feel the truck pull to the right. If I hit the brakes harder that back wheel locks up every time. Pulls the truck hard to the right and then when I let off the brakes it corrects itself to the left giving me what feels like a random wander. But it's not random at all. Predictable and exactly the same every time.

Now why the heck would my back right wheel lock up like that?
 

svastano

Contributor
Bronco Guru
Joined
Apr 8, 2017
Messages
1,379
Loc.
Pulaski, PA
Well I've got some more info. I figured something out.

She pulls to the right every time. The back right brake is locking up. Doesn't require a lot of pressure. It's the only wheel that locks up with light pressure. Even at slow speeds if I hit the brakes I feel the truck pull to the right. If I hit the brakes harder that back wheel locks up every time. Pulls the truck hard to the right and then when I let off the brakes it corrects itself to the left giving me what feels like a random wander. But it's not random at all. Predictable and exactly the same every time.

Now why the heck would my back right wheel lock up like that?

Could be just improperly adjusted brake or the shoes warn out and metal on metal... Could be a bad wheel cylinder on the opposite side not working at all and putting all the fluid to the other wheel.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Do you have Ford discs or is it a conversion? I have a D30 and had to go back and grind some more off the knuckles when the pads wore down to about 50% life. The caliper hit the knuckle and the braking was wonky making it pull when stopping.
 

jray

Full Member
Joined
Sep 20, 2009
Messages
340
My 72 did the same thing until I installed a 2 1/2 inch lift, new trac bar/bushings and radius arm bushings (4 degree C bushings). I figured it was the bushings.
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
Do you have Ford discs or is it a conversion? I have a D30 and had to go back and grind some more off the knuckles when the pads wore down to about 50% life. The caliper hit the knuckle and the braking was wonky making it pull when stopping.

I do have exactly this problem. I would not have known anything about it except one of the guys from Wild Horses who was it Super Cel pointed it out to me. The driver side is not yet making contact but the passenger side is very close. I don't believe the caliper is yet hitting the knuckle butt it won't be long. Doesn't explain why the back wheel is locking up but it sure as heck doesn't contribute to making things any better now does it. Tell me how you ground it down please. Did you grind the caliper or knuckle? Did you have to pull it completely off the truck or did you do it with a grinding wheel while it was still on there?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
The rear brakes share the same single brake line from the master cylinder to the junction block on the rear axle. so if the right rear is grabbing first then either the right side is adjusted tighter or brakes are contaminated or the real problem is on the driver side with either a plugged brake line, a stuck wheel cylinder or a much looser adjusted brake shoes. You could also have different size drums on each side by replacing or machining only one drum. so start with an examination on both sides, then adjust the brake shoes equally on both sides. then check if the brakes are applying equally if not then bleed the rear brakes. Put the brake centering tool in the H-Block and then bleed the passengers side rear first then bleed the driver side rear.

After bleeding remove the h-block tool and check if the brakes are now working properly on both sides.

If your drum brakes are adjusted differently on both rear brakes I would check the brake assembly since your rear brakes should be self adjusting. Maybe the star wheel assembly's are not properly greased and are stuck. On my Bronco I had grooves worn in my backing plates from the brake shoes and I had to weld them up and polish the surface flat again.
 

Attachments

  • drum-brakes-spring-guide.jpg
    drum-brakes-spring-guide.jpg
    249.8 KB · Views: 107

Kenny

Full Member
Joined
Jul 26, 2002
Messages
301
A lot of good reasons mentioned, but my first guess is that the right rear drum is contaminated with either brake fluid or gear oil. Check for a leaky wheel cylinder or axle seal. I once had a leaky rear cylinder that caused that wheel to lock prematurely which almost caused an accident.

If that's it, fix the leak, clean with a lot of brake clean and get new shoes for both sides.
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
You guys have been fantastic in helping me know where to look. I really do appreciate all of the advice.

Tonight I didn't have a ton of time but I managed to pull the wheel and drum off the right rear. No leaks. Brake shoes still have plenty of life. I will say the star wheel adjuster was awfully tight. I loosened it up a little bit. Tomorrow I'll get the driver side off and see if it adjusted the same way or if there are any issues on that side. Next step will be making sure that everything is adjusted equally and bleeding the brakes if necessary.

I'll let y'all know!
 
OP
OP
Tony Mele

Tony Mele

Jr. Member
Joined
Apr 3, 2016
Messages
132
Thanks for all the advice. I think I've got it right. I pulled both real wheels last night. The side that was locking up was adjusted significantly tighter then the driver's side. I cleaned them both up and got them adjusted about even. Took her out for a test drive and mashed on the brakes with my hands off the wheel. The truck tracks straight down the road. Tried it at all different speeds and didn't have any problems at all. I even locked em up on purpose to see what it would do and he kept running straight.

Glad it turned out to be something that simple. Appreciate all the help. As always a huge shout out to Nick and Paul.
 
Top