• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

I have had this idea...

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
Hydrostatic drive.
After watching some equipment running around with hydrostatic drives. Everything from streetsweepers, combines, crop sprayers, etc. I had an idea. I also see a flaw in the idea, but I will spoil it later.

So take a standard NP435/D20 combo. Both have PTO options. Put the pump from a hydrostatic drive on the transmission. Put the motor on the transfer case. What does this get you? Well, normally you have a nice NP435/D20 combo to drive around with. When things get interesting, transmission in nuetral and both PTOs go in.
Engine drives pump through transmission.
Motor (hydrostat output) drives into the PTO, which drives the input to the transfer case. Transfer case in low range, get your multiplication. No you can drive infinatly slow, actually stop and change direction without ever really stopping or loosing connection between drivetrail and the ground.

Big, expensive, power limited are all potential problems. But I don't see it as a way to drive all day. Just those real challengine spots.

But I suspect the PTO would not accept the power required to drive. That could get ugly. Then I thought some more, Doubler transfer cases. Cold duck would be nice. What you would want was the first case to be an all gear like the D20, D300, NP205. Not a design with a seperate reduction box such as the Toyota or NP203. None of the chain drive stuff I know of would work either. What you would want to do is put the hydrostatic drive on the front yoke of the transfer case. With the front axle engaged in high it will back feed power into the input of the crawler transfer case at transmission output speed. Then with output in low range, you get reduction. Use the crawler box to then drive the real transfer case (more reduction). You would need the crawler box to have the opposite side drop of what your front axle is.

The bad part is the only way I know this could be done is with an old Cold Duck kit. Just don't cut the front off the crawler box. I don't know of any crawler box conversions that use a NP205 or D300 as the center transfer case. I always thing of the seperate reduction box transfer cases as the donor.

I will admit I have done no real engineering on this. I have not looked up and of the power capacitys, torque requirements, speed limitations, etc. Packaging thoughts have gone as far as put the drive on the opposite side as the front driveshaft, no other thoughts. I don't work around enough hydralics to really know how well this might work. I was impressed with the parking lot sweeper that ran a fixed engine speed and the rocker foot pedal varied speed and direction to what ever the operator wanted.

I am sure someone has tried something like this before on some kind of crawler. I am sure that there are issues I am completely overlooking. But thought I would throw out the thought and see what comes back.
 

Socal Tom

Bronco Guru
Joined
Feb 12, 2004
Messages
2,442
Loc.
San Diego, CA
I think you are losing the benefit of the hydro drive if you just use it to spin drive shafts. If you are going to do it, I would dump the drive axles all together and use four hydro motors, one for each wheel. If you still want the live axle setup, you could mount them on solid axles.

The benefit is you have much better break over angle cause no driveshafts and no D20 hanging down. You also gain the ability to power each wheel indepently. You can lock one wheel and pivot, etc.

Tom
 
OP
OP
Broncobowsher

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
I think you are losing the benefit of the hydro drive if you just use it to spin drive shafts. If you are going to do it, I would dump the drive axles all together and use four hydro motors, one for each wheel. If you still want the live axle setup, you could mount them on solid axles.

The benefit is you have much better break over angle cause no driveshafts and no D20 hanging down. You also gain the ability to power each wheel indepently. You can lock one wheel and pivot, etc.

Tom

Yes, but you would loose your ability to drive on the highway.
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
i thought about the same thing years ago. my idea was to put a pump on the back of the trans itself (no t-case required), and run hydraulic lines directly to the yokes on the axles via whatever it takes to drive them.

take a look at the forklifts that hang on the back of semi's that deliver grass or whatever. they have small pups at each wheel and go off road all the time. never seen one rock crawl though, or go fast for that matter.

get a load of this!
http://thekneeslider.com/archives/2007/05/22/hydrostatic-drive-diesel-motorcycle/


looks like someone tried the idea, and you're right about the turtle speed;
http://www.youtube.com/watch?v=kXuckwyWzxA&feature=related
http://www.hydraulicinnovations.com/
 
Last edited:

Gummi Bear

Bronco Guru
Joined
Jul 8, 2003
Messages
3,647
There's a fella on Pirate that's building a hydro drive buggy, you may look at it.

I've always thought it was pretty neat, but in something as small as a Bronco, finding parts would be tough. My small amount of research turned up parts for tiny yard machines and then a leap up to large earth moving machinery.
 

AWS

Sr. Member
Joined
Aug 2, 2004
Messages
596
Loc.
ST LOUIS
Blow a hose and 20 gallons of hot oil comes out fast. Tree Huggers would have another reason to complain about our hobby. I'm not bashing anyone's idea, but save the hydrostatics for construction equipment. Also a Hydro unit with good traction will eat dana 30/44 and 60's, sometimes both ends at once. And another bonus unless more valving is installed the weight of the vehicle could overcome the drive motor (it will act as a pump) and down the mountain you go.
 
Top