• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Torque steer

chuckinphx

Full Member
Joined
Nov 14, 2009
Messages
279
Loc.
phx
check you u bolt nuts..
I stopped some of this by checking how tight the u bolts were. mine were not very tight..

Im on the edge of my seat with good a fix to this, got same problem, i know i need some more caster in the front, very darty on freeway 5.5 lift 35's

look up traction bar.. lots of info
 
OP
OP
E

ehumaui

Sr. Member
Joined
Apr 17, 2004
Messages
913
Traction bar or torque, im running two. Duff over both springs and custom single torque bar, passenger side. I'll link the video.

Rc
 
OP
OP
E

ehumaui

Sr. Member
Joined
Apr 17, 2004
Messages
913
Here is a pict of the track bar, looks good to me?
 

Attachments

  • ImageUploadedByTapatalk1317184436.463694.jpg
    ImageUploadedByTapatalk1317184436.463694.jpg
    59.5 KB · Views: 133

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Can you take a pic from farther away Russell? Or bring it over for me to look at?
Reason I'm asking is that, even though they may look somewhat parallel because of the bend, I'm thinking that the actual mounting points are off.
Maybe you can look at it and verify the distances between the upper mounts of the draglink and trackbar, then the lower mounts. If they're roughly the same, fine, you're good to go. If they're off however, whether it's actually causing your torque steer or not, it's not helping things.

And on the proper C-bushings for your custom made radius arms, The best way to check to see if they're right for YOUR particular Bronco is to take it down to an alignment shop and have them give you an exact readout of your current caster.
Then you will know what bushings to use.
What bushings did you put in?

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Along with your possibly misaligned bars, you probably have a little slop in the steering. And slop in the steering will always feed the monster. Making driver-input adjustments more vague and harder to read and compensate for.

See if you can adjust the draglink and tie-rod so that they tie-rod is angled so that the mounting pad where the lower draglink end mounts is at closer to a 45° angle upwards. Right now it's facing forward, and maybe even a bit down (could be the angle of the pic though) which would usually give the tie-rod a bit of rotational movement (play) before it moves side-to-side (steers).
Once rod ends get older and looser too, that rotational movement just gets more pronounced.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Giving Jerry a ride to work, then available on and off during the day.
You working normal hours, or do you have Friday off?

Paul
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
Personally, I would ditch the stock track bar mount and go to an axle riser bracket....assuming that you are sporting the track bar drop bracket. As well, the drag link with the big S in it is troubling to me. I guess it may be OK, but it looks questionable.

I have a similar setup (lift, tranny, ext. Radius arms). I dont have alot of noticable torque steer...although if I am really on the gas I can feel a shift as I come off the gas. But I would say that my truck is very stable. Double check your torque on all the hardware. Are all the bushings new...really new not --"they had a few seasons, so we figured they were alright"--new? Also, get sime extra hands to do the steering thing, while you or someone with some experience look for stress, cracks or loose connections.

With the ladder bars, the rear should be stable, provided it was all welded up straight. Another reason to have an alignment shop take a look at it.

Good luck!

John
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Agree about the alignment shop. Recommended that to him this morning again. Mostly for the caster reading, but getting the down-low on how the front and rear are in relation to each other, like you said.

I just drove it a little while ago and I must say, I'm impressed with his calm demeanor when describing the issue. It's got some seriously wicked handling issues! It not only wants to steer itself, but is not really consistent enough to easily compensate with steering wheel input from the driver.
It's still got a stock 6-turn power steering box too, which feels decently tight, but has absolutely ZERO feedback to the driver as to when the truck is going to go play in the next lane. Some times it just needs a tiny bit of English, sometimes it needs some real input.
Fun fun fun...

Although the s-shaped draglink is a decently working setup that we've been selling for years, it's more of a fully-adjustable replacement for mildly set up rigs. It starts to show it's weaknesses as the tires get larger and lifts get higher.
It's capable of decent geometry in some aspects, but since it keeps the near-stock rod diameters and the shorter draglink style of the stock setup, I'm pretty sure that it can at least contribute to what he's seeing.
Under normal steering inputs though, the mild S-curve of the draglink does not flex visibly, even with the larger tires and wheels.

It should work decently under most circumstances, but is probably borderline in Russell's case, since he's got a Detroit in the rear, multiple traction bars and stiff shocks that might transmit inputs more radically between the front and rear, and some pretty hefty 35's with what look to be 10" wide wheels with lots of negative offset sticking way out he side, putting lots of torque on the steering linkage.

What we also found while performing the usual steering test, was that one tie-rod end was loose, and the main tie-rod was twisted in such a way as to have a pretty acute angle for the draglink's lower mounting point. Probably a good 75° off of stock.

So we should be hearing from him pretty soon I would think (he's a fast worker) about what, if any, effect tightening the one rod end and re-aligning the tie-rod have on how it feels.
Just one thing at at time though, so next he'll try disconnecting the old traction bars and leaving his new fancy one hooked up.
Next would be getting an alignment readout from a shop.
Then we'll be swapping out his steering linkage for my modified F150 setup if it'll fit. Since it's the larger tapered ends, I'm not sure how tight we'll get them to fit into the stock Bronco knuckles. If it'll work though, that'll give him a good idea of what, again, if anything, a longer draglink will do for the feel of it.

His trackbar is very tight and the upper drop bracket does not flex noticeably. But we talked about raising the upper, then adding a lower riser bracket anyway. Down the road a bit still...

Paul
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I forgot to mention, that after driving it, I think a lot of what is driving the movements is the Detroit. We didn't check air pressures or actual tire diameters (which we should have), but it sure felt like something was steering the truck without any feedback from the steering system.
And some of the most pronounced sideways movements were not in conjunction with any diving of the front or rear suspensions. Even a simple, quick and clean shift with the clutch could (though not always) result in a quick direction change.
Since the front end was not diving noticeably with his dual-shock setup, the amount of direction change was very odd. Until you wrap the existence of the Detroit into the equation.

Maybe some of you other Detroit owners can chime in with your experiences with lifted trucks and lockers?
Ive driven Detroit-equipped Broncos before, and that's what this felt like initially, but I must say that it was more pronounced than I remember any others being.
Feedback would be appreciated.

Paul
 

ken75ranger

Bronco Guru
Joined
Jan 27, 2002
Messages
5,069
Loc.
Troy, NY
Maybe some of you other Detroit owners can chime in with your experiences with lifted trucks and lockers?
Ive driven Detroit-equipped Broncos before, and that's what this felt like initially, but I must say that it was more pronounced than I remember any others being.
Feedback would be appreciated.

Paul
My Bronco has a linked suspension with a Detroit in the rear. I haven't gotten around to doing a sway bar and I'll tell you it's a hand full keeping in any lanes once you hit the gas hard.

It was annoying with the 302. I just went to a 351 with a better cam and it now a real pita using the additional hp on the street.

I it were me I'd be looking for a decent diameter sway bar....;)
 

bluesbish

Full Member
Joined
Jan 30, 2011
Messages
278
Loc.
Upstate New York
I am running 5.5 lift, 38's, detroit and 8 shocks with 351. oh, also 4x4x2 box. when I first got my bronco out of the shop, it was pretty squirly. took it to work and put it on the alignment rack and had 3.5 degrees caster which was right in spec according to the machine but I knew better. I left it like that because I was in a hurry and handling was much improved after correcting my toe. I dropped pressures from 35 to 30 psi and noticed a big improvement. after driving about a week I was still not happy. I crawled under the rig and cranked the caster back as far as I dared keeping front driveshaft angle in mind. I was able to make this adjustment due to my BC broncos radius arms!! so I imagine I am running 5 or more degrees positive caster and I could not believe the difference. However, due to the detroit, I can always anticipate a slight yank to one side under hard acceleration or when shifting gears. so I guess with a detroit or similar locker, you will always have this concern(thats why they give you a sticker to put on your dash). But the concern is minor as long as all other issues with steering and handling are addressed and corrected.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
so I imagine I am running 5 or more degrees positive caster and I could not believe the difference. However, due to the detroit, I can always anticipate a slight yank to one side under hard acceleration or when shifting gears. .


That is why I shoot for 6 degrees plus/minus 1 when building a rig. ;) It really does help.
 

dieselbronco

Full Member
Joined
Jan 18, 2009
Messages
151
Loc.
Tolland CT
So today I installed 7% front c- bushings and most of my squirly steering and tourq steer is gone. Super easy fix. ( 5.5 inch lift, extended radius armes, 35 inch tires, no lockers)
 
OP
OP
E

ehumaui

Sr. Member
Joined
Apr 17, 2004
Messages
913
Well just ck the shed and found the bushings box. I fogot I switched the 7deg out.

I did twist the drag link back. Haven't had time to drve it.


Rc
 

broncotime

Bronco Guru
Joined
Jun 30, 2003
Messages
1,188
Loc.
Grapevine, Texas
Good point with the tire size. Start simple by checking tire pressure.
I can tell when my rear tires are more than 3 or 4 pounds different in pressure from the acceleration torque. Even with equal pressure, it is something I just had to get used to. Not too bad if you stay off the gas some when shifting.

Detroits in the rear with 3.5 suspension + 2 inch body
 
Top