• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Track bar riser or tracking bar drop bracket?

BeardedBlues

Contributor
Sr. Member
Joined
Jan 23, 2012
Messages
595
1974 with 2" body lift and 3.5" suspension lift. Will be street and trail rig. Right now I am trying to figure out which components I need for the suspension lift.


Should I go with track bar riser or tracking bar drop brackets?








Adjustable tracking bar - from BCB

Adjustable drag link

Tracking bar drop bracket or track bar riser ???????

Drop pitman arm

Extended drivelines

Leaf spring shim kit

Extended brake hoses and E- Cables

4x Bilstein shocks

New springs for front

New leafs for back
 

Lmfp

Bronco Guru
Joined
Jun 28, 2011
Messages
1,496
Loc.
Lake Charles, LA
Track bar riser is the way to go. It puts less stress on the frame makin it less likely it'll tear. And really the adjustable track bar isnt neccessary it helps make sure the front axle is dead center if your that anal about it. But the riser by it self centers it up pretty darn good.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
The drop bracket puts a lot of additional twist into the frame (more leverage compared to stock bracket) and the frame is not known for it's strength in that area. The riser is a better way to go because it gets welded to the axle which is plenty strong.

A bunch of us CO folks just converted to 1 1/2" DOM TRO steering setups and went with Wild Horses risers. The riser is very stout, 3/8" thick I think. The TRO gets the linkage up and out of the way of rocks. I bent and straightened my stock linkage too many times.
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
i second the trac bar riser. Should be able to make one out of some simple 2x3 or 2x4- 1/4" wall rectangular tubing for about 5 bucks. Shouldnt need a drop pitman arm though as the will put unwanted stress on the box. I would look into doing the chebby tie rod end and do it tie rod over, rather than a stock adj drag link.

I have a 5.5" sus lift, with Chebby TRE-TRO swap and stock pitman arm, with riser bracket.
 

Attachments

  • IMG_1892.jpg
    IMG_1892.jpg
    89.1 KB · Views: 510
  • IMG_1893.jpg
    IMG_1893.jpg
    121.1 KB · Views: 486

pipermike

Full Member
Joined
Oct 9, 2010
Messages
253
Track bar riser for sure. If you are going to use the stock track bar make sure you have the axle mounted and the track bar installed to check fit before you weld it solid or it may not line up. Ask me how I know this :)
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Riser is the better way to do it.
A drop bracket will interfere with a tie rod over conversion if you ever go that route.
Countless frames have been torn with the drop bracket.
 

Jeff76

Sr. Member
Joined
Dec 23, 2011
Messages
638
Loc.
Alpharetta GA
The drop bracket puts a lot of additional twist into the frame (more leverage compared to stock bracket) and the frame is not known for it's strength in that area. The riser is a better way to go because it gets welded to the axle which is plenty strong.

A bunch of us CO folks just converted to 1 1/2" DOM TRO steering setups and went with Wild Horses risers. The riser is very stout, 3/8" thick I think. The TRO gets the linkage up and out of the way of rocks. I bent and straightened my stock linkage too many times.

I've got a question about this. I saw a thread the other day where there was a clearance problem between the track bar riser and the frame. The truck also had the TRO. Is there a minimum lift where this combination works? My memory is poor, but I think the truck in question had a 2-3" lift.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I've got a question about this. I saw a thread the other day where there was a clearance problem between the track bar riser and the frame. The truck also had the TRO. Is there a minimum lift where this combination works? My memory is poor, but I think the truck in question had a 2-3" lift.

The top of the riser is slightly taller than the stock bumpstop. It could contact the frame unless a taller bumpstop is installed. I think a 3 1/2" lift is what WH recommends as a minimum. With less lift you may not want to do a TRO swap. It puts the tierod very close to the stock lower trackbar stud/nut which will limit turning radius. Tierod moves back in turns.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
I've got a question about this. I saw a thread the other day where there was a clearance problem between the track bar riser and the frame. The truck also had the TRO. Is there a minimum lift where this combination works? My memory is poor, but I think the truck in question had a 2-3" lift.

That may have been one of my posts. I have about a 2.5-3" suspension lift and I had a riser on my axle for many years. It's much better than the frame drop bracket as others have mentioned but you do need to watch your riser/frame clearance, particularly if you have soft front springs and like to exercise your suspension (I am guilty of this).

One other benefit of the riser on the axle compared to a frame drop bracket is that it helps correct your front suspension geometry in a way that helps handling. The drop bracket off the frame hurts it.

Todd Z.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
i second the trac bar riser. Should be able to make one out of some simple 2x3 or 2x4- 1/4" wall rectangular tubing for about 5 bucks.
I built almost the exact same riser, 2 x 4 x 1/4 wall, with a 2 x 2 brace, and 3/4" bolt through from the front! Very happy with the way the suspension works.
 

Attachments

  • Track Bar Riser.jpg
    Track Bar Riser.jpg
    275 KB · Views: 397

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
My first round I made my own, and it didn't look very good.

I later purchased an offset multi-adjustable bracket from RuffStuff and TIG'd it to my axle housing and now it's far better looking than the last piece. It's also a TON cheaper than the Bronco vendors, but requires you to cut off the old bracket and measure where you are putting the new one.

2012-03-23011019.jpg


2012-05-30213007.jpg
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
What brand Tie rod / Drag Link it that? What year Bronco?
It's the Chebby 1 ton conversion. The tie-rod was made by Bent Fab here in Phoenix. I made the drag link with some help from jackholeracer (Vince) who did the machine work. It's a 70 Bronco with a 76 Dana 44. I used knuckles from a 79 F150 so I didn't have to worry about wheel clearance with the Chebby TRO conversion.

The front suspension is pretty much all custom now.
4x4x2 PS box
Chebby 1 Ton steering with the custom links
BC Broncos track bar.
Custom (Home) made Track bar frame bracket and axle riser
F150 steering knuckles.
Custom (Home) made heavy duty lower coil cups
Cage 5 1/2" coils
Custom (Home) made coil towers 2 1/2" taller than stock
Lars Bars
Custom (Home) made shock hoops
Bilstein 7100 shocks

I think that's about it... You can see pics of the conversion here:
http://www.emotoman.com/4x4/2012/steve/
 
Last edited:
Top