• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

tmaddux911

Jr. Member
Joined
Jan 19, 2013
Messages
117
respirator with old filters. I figured the filter life was time used, not time open. Guess I'll pick up some more filters.

A little late for an input i know.... OSHA requires us to dispose of our filters after 16 hours of use or one week after being open, we even have to write the date on them. I myself at home go with the 16 hour rule only and zip lock baggy them when not in use. just food for thought.
 

tmaddux911

Jr. Member
Joined
Jan 19, 2013
Messages
117
Welcome to the thread;) any photos of yours?


1966,351w,m5od,205....3.5" lift, 2" body, 37/13/15 boggers


I started a thread about my Bronco you can search it under my name there is a few photos on there along with my story of how i got it.

Tom
 

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Rattle can paint job on the firewall to get ready for the HB and powder coated brackets. All of my floor pans need to to be replaced so instead of doing them now, I'm going to wait until I have the front clip off for tube work. I don't want to get into bodywork before my drivetrain is where I want it. This will work for now.

5AF8FB6F-90B5-4182-B9D5-1408D7326681-639-000000D7E311BEBD.jpg

056F164E-DA5B-45E6-A66C-4CB1F56C72F2-639-000000D7FAEF8C49.jpg
 

markperry

Bronco Guru
Joined
May 8, 2009
Messages
4,175
Installed a new drive-shaft and 3* pinion shims....3* was not enough, so I had to order 6* shims!
 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
Worked on the mounting base for my Driver Side FJ mirror! Hopefully get it mounted by the weekend and maybe painted and wired up!
 

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
Installed the carpet and front seats. Placed the cage and drilled holes for mounting bolts. Prepped rear seats for install with longer bolts. The plan is to paint the cage flat black, but I don't have time for that right now, so primer it is.

660BA5B5-EB0A-4E30-90A3-65584C524B48-3808-000002CD9B1028FE.jpg


7FED1E8C-7CFF-48B7-B352-93C3E3CD04CA-3808-000002CD7C3E746E.jpg


3BF082E9-0133-4BE7-8E4D-16E003902AA3-7817-000005F46C716E08.jpg


D2E93008-47A1-44D5-8289-6D12BBE3E81D-3653-000005951DEC9561.jpg


528028BC-2FFE-4C67-A98A-3A9449F69FB6-3653-00000595255B1FD7.jpg
 

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Reading through a timing thread started in the Tech forum. I discovered what I had missing when tuning my 302. My vacuum advance was plumb to direct manifold vacuum instead of the ported vacuum on the 2150 carb.%) So between jobs this afternoon I move the vacuum advance hose to the carb and reset the timing. End up at 11-11 1/2 degrees. Boy what a difference this simple change made. Idles a little smoother and gave the Bronco some more pep.:cool:;D

This is what I love about this forum. I learn something new every day.:cool::cool:

Thanks everyone!
 

nathan.hall1

Sr. Member
Joined
Feb 3, 2006
Messages
556
Loc.
Central Washington
Well I got the rest of the little stuff, so I could fire it up (still waiting on throttle cable) I fire it up it ran for a second and huge flame backfire out of carb....

So I started thinking what could cause that? I thought of timing...I did remove the distributor (I was sure I got it back in exactly the way in came out)
I too read that timing thread and used it as a reference and refresher on timing
so I get #1 to TDC and the rotor is pointing in between 1 and 8. So I figure I had it close enuf to run but not quite in time. so I pulled it adjusted over a tooth now it's right on, I double check my firing order to be sure and it's 1130 pm, and my little girls room is right above the garage....so the moment of truth will have to wait until after work tomorrow...
 

dube

Bronco Guru
Joined
Feb 19, 2012
Messages
1,042
Loc.
big lake Mn
pulled the radiator out and fixed the leak on the petcock. po never put teflon tape on it.
lowerd the brackets and remounted the radiator filled her up and took it for a little drive.
 

Fireball05

Bronco Guru
Joined
Oct 7, 2012
Messages
1,822
I don't mean to brag, but I had a huge day in the garage today, just check out this before and after photo. ;D





Seriously though, huge shout-out to Wildhorses and Dirtdonk (Paul) who helped me troubleshoot my brake problem. I installed a new master cylinder and rear brake line and had trouble bleeding the system. Ended up sorting out a problem with the stock proportioning valve, but still had way too much pedal travel. All searching online led me to believe there was still air in the system. Called Paul and he told me to check the pushrod adjustment. Ended up that the aftermarket MC required the pushrod to be pulled out 1/4" past factory spec. Would have never thought to check that, so many thanks to Paul. After adjusting it out, am very near the end of the screw travel (3 or 4 threads) so added a jam nut as a temporary fix.

Moral of the story... check the new MC piston depth and adjust rod as needed. Or do it my way and spent 4 or 5 hours and 2 quarts of brake fluid bleeding and rebleeding and scratching head and cursing first :)




Paul also informed me that WH sells this deluxe master cylinder which has adjustable piston depth and a much more secure cap than the standard replacements. The leaking MC cap/lid is a very common problem, so for a few bucks more I would've gone with this one had I known about it.
 

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
Bolted down the cage, bolted down seats, installed the gas tank, fired it up!
 

Burkulater

Full Member
Joined
Mar 30, 2011
Messages
316
Loc.
Lancaster, PA
I don't mean to brag, but I had a huge day in the garage today, just check out this before and after photo. ;D





Seriously though, huge shout-out to Wildhorses and Dirtdonk (Paul) who helped me troubleshoot my brake problem. I installed a new master cylinder and rear brake line and had trouble bleeding the system. Ended up sorting out a problem with the stock proportioning valve, but still had way too much pedal travel. All searching online led me to believe there was still air in the system. Called Paul and he told me to check the pushrod adjustment. Ended up that the aftermarket MC required the pushrod to be pulled out 1/4" past factory spec. Would have never thought to check that, so many thanks to Paul. After adjusting it out, am very near the end of the screw travel (3 or 4 threads) so added a jam nut as a temporary fix.

Moral of the story... check the new MC piston depth and adjust rod as needed. Or do it my way and spent 4 or 5 hours and 2 quarts of brake fluid bleeding and rebleeding and scratching head and cursing first :)




Paul also informed me that WH sells this deluxe master cylinder which has adjustable piston depth and a much more secure cap than the standard replacements. The leaking MC cap/lid is a very common problem, so for a few bucks more I would've gone with this one had I known about it.

The before shot was correct change it back that's how virtually every older vacuum system out there is set up haven't you learned anything :p

Our poor plow truck had a sawed off chunk of a green broom handle plugging a line for several years.... That was cute too
 
Top