• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

ET

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,800
Loc.
Dallas, TX
Remade and install a hydro hose. Changed out belt tensioner and made a tunnel cover for old np435 hole. I can see the light at the end of the tunnel.

Eugene
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
Installed my JB Fab twin stick on the '72. Installed it in 32 easy steps...

1) Remove bolt holding in J-shifter.
2) Remove J-shifter.
3) Go from barn to shop and get the dremel tool.
4) Cut flags on the rails.
5) Set the dremel down and remove the reverse shift rod that is in the way.
6) Crawl under the truck and retrieve the reverse shift rod clip that you dropped.
7) Go from barn to shop and get more cut off wheels (apparently one is not enough)
8) Cut some more.
9) Go from barn to shop and get the other dremel tool after the first one dies. Bring back a beer.
10) Open beer.
11) Start drinking beer.
12) Finish cutting (note to self, "Self, the new dremel tool cuts much faster than the old one.")
13) Read directions on the JB Fab kit. Directions say remove old shifter. Cut flags. Install twin stick.
14) Ponder why there are two bolts with the kit and where the washers go.
15) Figure out that the other bolt is probably for the T-shift case, and I don't need it.
16) Put the correct bolt through the hole towards the front of the vehicle.
17) Get out of the truck and crawl under to get the bolt that was just dropped.
18) Put the correct bolt through the hole towards the front of the vehicle.
19) Put the rear axle shifter on.
20) Insert washer (I think).
21) Put the front axle shifter on.
22) Install washer (I think)
23) Install lock nut.
24) Bolt spins, put wrench on the nut so it won't fall off.
25) Crawl under the truck
26) tighten bolt with socket wrench
27) Put the wrench back on the nut
28) Crawl under the truck
29) Finish tightening the bolt
30) Test drive! ;D
31) Put the spare parts away.
32) Clean up

Other notes to self, "Self, you are going to have to remove the shifter and straighten the front axle shifter so it doesn't hit the transmission shifter when front axle is in high. Do that some other time. Now you can build the cover for the tunnel that the PO cut out."
 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
Still workin on the mirrors on my truck! Today I am gonna get some ABS Plastic to repair my cracked driverside mirror base!
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Working on the EFI swap, not good, Donor had issues so I got pissy, snatched all the EFI stuff off and put the carb back on, Now to figure out what is causing the miss, Might just be Chipper being pissy over me messing with it and letting it sit for 2 months..
 

Adarcy

Sr. Member
Joined
May 19, 2010
Messages
826
Nothing to the bronco, but I am in the middle of replacing some pulleys, the belts, the thermostat, some sensor gaskets and seals on the back of the engine, and some seals under the transmission pan on my wife's bmw x5. Really making me like working on the bronco more and more! No room to do anything on this sucker!
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
Nothing yet, still working on my nephews F150. It's got a cracked intake and it's pouring coolant everywhere.

I hope to start my Wild Horses 1" body lift as soon as I done with the truck.;D
 

BIGED

Guru ????
Joined
Oct 30, 2007
Messages
2,003
Went for a ride in it. ImageUploadedByTapatalk1360438003.624344.jpg
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Gave her the attention she has been craving, she showed her ass a bit, but in the end just like a woman, a little money spent on them makes them happy! Going for a ride...................

EDIT: Ride complete, Took the better half on a long ride, Paid a visit to Dad, Sure miss him, I still remember the look on his face the first time I drove up in Chipper, Priceless!'
Then of course all the kids wanted to go for a ride, so away we went! Got back and my 2 Great Nieces were both crying wanting to go on a Bronco ride, so away I went again!( No carseats as all we did was a little trail ride here on the property)
 

Attachments

  • 02092013-1 (2) (Large).jpg
    02092013-1 (2) (Large).jpg
    107.1 KB · Views: 64
  • 734659_564216226922406_436173813_n.jpg
    734659_564216226922406_436173813_n.jpg
    68.5 KB · Views: 58
Last edited:

mudstud

Contributor
Bronco Bonehead
Joined
May 19, 2005
Messages
1,517
Loc.
Excel
With help of fellow Bronco Bother with a keen eye we discovered that the parts Bronco has a 351 in it. Thanks beaux312.
 
Top