• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New motor, same problem.

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
So, some time ago my old motor lost power and wouldn't go over 35 MPH I figured something had gone very wrong internally and just opted for a new long block. I found a motor from another member on here and installed it, putting all the parts (intake, carb, timing chain cover etc..) onto the new motor. Well after getting it going the new motor is doing the exact same thing, spitting and sputtering and running about 35 with the pedal on the floor. Is it the carb or did I hit the jackpot and get two bad motors? Any help is appreciated thanks guys.

And since we all like pics I threw a couple in from today.
 

Attachments

  • 20140217_152957.jpg
    20140217_152957.jpg
    90.1 KB · Views: 122
  • 20140217_161750.jpg
    20140217_161750.jpg
    80.3 KB · Views: 110
  • 20140217_181543.jpg
    20140217_181543.jpg
    87.6 KB · Views: 98

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
I would guess your carb is way out of tune. I had similar issues a long time ago it was the 1406 pos carb
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Id agree Probably need to rebuild and make sure the carb is setup properly.. How about the distributer? Did you swap that over as well? Have you checked the points gap? Made sure the advance is working correctly? Made sure the vacuum advance is hooked up and working? How about distributor cap and rotor?
Kinda sounds like you did a engine swap for something that may have been a simpler and cheaper fix. Bad engines tend to lack power but will usually still run and accelerate ok.
 

Jesse37932

Jr. Member
Joined
Feb 4, 2012
Messages
73
Loc.
Knoxville
Happened to me

I did the same thing in an old ford van straight 6-engine didnt have any power, replaced it-same thing. Turned out to be the carb...
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Awesome thanks guys. The old motor had bad compression also so I thought for sure it was something internal so I guess I'll figure out a new carb, I rebuilt the one I have first time I had ever done it I though I followed the directions pretty well, but who knows.

A piece is broken on this carb as well it's one of the posts that sticks up if you look at the picture you'll notice the left one is gone...
 

Attachments

  • 20140217_195342.jpg
    20140217_195342.jpg
    87.7 KB · Views: 134
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Also does anyone know a good replacement two barrel that will fit the intake? I've tried looking and my head just starts spinning with all the options.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Id agree Probably need to rebuild and make sure the carb is setup properly.. How about the distributer? Did you swap that over as well? Have you checked the points gap? Made sure the advance is working correctly? Made sure the vacuum advance is hooked up and working? How about distributor cap and rotor?
Kinda sounds like you did a engine swap for something that may have been a simpler and cheaper fix. Bad engines tend to lack power but will usually still run and accelerate ok.

I stole a known good distributor from my old mans bronco and tested it then swapped back when it did the same thing that's all the testing I've done to that part of the motor.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
First, make sure you have good fuel pressure while you drive. Then, I'd agree its the carb.
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
Ditch the points buy a pertronix, buy a rebuild kit for the carb, make sure there are no vacuum leaks, replace the cap and rotor, plug wires, and verify you have good gas flow. .. suck bang blow
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
First, make sure you have good fuel pressure while you drive. Then, I'd agree its the carb.

I switched over to an electric pump it's a cheap one until I can get something better but it's supposed to provide 4-6 lbs.

And thanks for all the replies everyone.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Id say its probably down to a carb issue then. The 2100 carb is easy to rebuild you just have to make sure the all passages are clear. And the booster venturi assemblys are not damaged make sure there passages clear as well. If you do just want to get another carb then most parts stores sell factory replacements. There are also some carb shops on line that sell rebuilt carbs.
That broken bowl vent tube is no big deal. It has nothing to do with how its running.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Id say its probably down to a carb issue then. The 2100 carb is easy to rebuild you just have to make sure the all passages are clear. And the booster venturi assemblys are not damaged make sure there passages clear as well. If you do just want to get another carb then most parts stores sell factory replacements. There are also some carb shops on line that sell rebuilt carbs.
That broken bowl vent tube is no big deal. It has nothing to do with how its running.

Okay good deal, I already put a rebuild kit on it once. Would there be any reason to do it again Or do I cut my losses and get a new carb. I guess another option would be getting someone else to replace it.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Sometimes the carb just randomly dumps fuel out of that broken tube too...forgot to mention that.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Also does anyone know a good replacement two barrel that will fit the intake? I've tried looking and my head just starts spinning with all the options.

Don't laugh but most of the chain parts stores can order you a replacement carb. I did this some 14 years ago as my carb was missing several parts and held together with wire and bubble gum.

I received a holly rebuild 2 barrel that I put on and it cranked right up. I set the idle and it's been gong every since. I've had to put a couple of accelerator pump diaphragms in it and clean the ethanol sugar crap out of it a few times but outside that, it's been money.

Got mine from Auto Zone.

Tim
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Sometimes the carb just randomly dumps fuel out of that broken tube too...forgot to mention that.

Could be a lot of your issue. Either the float is set to high or you have some dirt/debris in the needle seat which is causing it to flood. Of course if the float level is just to high you could be running extremely rich which could cause some of your issues when driving.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Carbon/ black color/ wet from to much fuel. basically check the plugs to see there condition. It can tell you a lot. Or it can tell us and we can tell you.;D
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
It seemed slightly wet would I pulled it. The plugs only have 45 minutes or so on them.
 

Attachments

  • 20140217_213152.jpg
    20140217_213152.jpg
    54.7 KB · Views: 68
Top