• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New motor, same problem.

OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Ill post a video of the horrific display tomorrow.
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
Im not a hook a machine up to the engine with timing. I always did buy sound. I would remove and plug the vacum advance. Loosen the bolt on the dizzy. Hold it have someone start the motor and slightly turn it until it smooths out
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Do you have a vacuum tree behind the carb,if so see if any of the vacuum connections or nipples are corroded. Is it a stick or automatic? If automatic check the vacuum line that goes to the trans for leaking. If it will idle long enough you can use air to blow around the base of carb and intake seal areas to see if the idle changes, which could be a leaky carb or intake gasket.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
You have a late model distributer it has 2 vacuum ports designed for the 2150 carb. Do not use the vertical port next to the cap that is for a smog function. You need to use the port on the end for vacuum assist. Your vacuum assist must come from a ported vacuum source. The vacuum port you have should not have vacuum at idle. If it does it won't work properly and you either need to swap to a newer carb with the vacuum port under the fuel bowl or swap to an earlier distributer from a 289 engine with a screw apart vacuum can. They work differently.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
You have a late model distributer it has 2 vacuum ports designed for the 2150 carb. Do not use the vertical port next to the cap that is for a smog function. You need to use the port on the end for vacuum assist. Your vacuum assist must come from a ported vacuum source. The vacuum port you have should not have vacuum at idle. If it does it won't work properly and you either need to swap to a newer carb with the vacuum port under the fuel bowl or swap to an earlier distributer from a 289 engine with a screw apart vacuum can. They work differently.

Okay I'll be honest you lost me. I use the front port to the carb for vacuum assist and don't have anything on the vertical port which is how it was before it all went to crap is this correct?
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
I think This is the one he's talking about, don't use the top connection ,use the other one second pic.But I see you are not using the vertical one so I a little confused. Did it run fine with the old engine hooked up that way? Before everything thing went to hell.
 

Attachments

  • engine new stuff 009.jpg
    engine new stuff 009.jpg
    67.8 KB · Views: 26
  • engine new stuff 010.jpg
    engine new stuff 010.jpg
    67.8 KB · Views: 24
Last edited:
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Yeah there's a picture of mine earlier in the thread I think I'm hooked up fine.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
2 vacuum ports have nothing to do with the 2150 carb the dual advance units have been around way before 2150's came out. My 71 still have the daul advance and my 73 did have it. Neither of which came with a 2150 carb because 2150's were not even being produced yet.
The 2 port cannisters are basically emissions related. The rear port retards the timing which was usually done to ewduce engine temps at idle. There are temp swtiches and delay valves that are also hooked to the vacuum lines that go to the cannister.
All in all the single port advance cannsiters are the ones to have unless you are required to run the emissions equipment.
As I said I run the dual cannister still on my 71 but with only the front port hooked up. It does seem more sensitive to timing adjustments than my 73 not real sure why as i havent really dove into the 71 to see what could be different.
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
How many volts do you have to your coil as well. Ballist resistors can can a huge issue.. I would also ditch those points for a pertronix. There cheap and work awesome. Best upgrade for a stock ignition. Man I wish you lived closer. I wouldn't leave unit its running right lol.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
How many volts do you have to your coil as well. Ballist resistors can can a huge issue.. I would also ditch those points for a pertronix. There cheap and work awesome. Best upgrade for a stock ignition. Man I wish you lived closer. I wouldn't leave unit its running right lol.

Haha that's what I need. Someone to come show me what's up. Beverages provided of course. Haha
I guess it Is time to look into ditching the points.
I'll get the tester it tomorrow and check my voltages.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
While electronics are a good upgrade. You should have no real issue getting it to run with points. If they are adjusted properly they work. Just they do wear and cause the timing to change over time. Where the electronic ones are stable and stay in adjustment so they tend to provide a better spark. Id get the engine running right before just swapping on a pertronix.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I don't remember if this has been discussed, so sorry if this is a repeat, but since you got a new long-block, with supposedly a new cam, did you do an initial cam break-in procedure on the new engine?
This is a flat-tappet type cam? Or a roller?

If a flat-tappet, and you did not diligently follow the break-in procedure, you could be running with a buggered cam.

I seem to fixate on this possibility a lot, and it usually turns out to be something simple and inexpensive rather than the bad cam scenario.
But that doesn't mean it can't happen.

Good luck.

Paul
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Not too surprising the new carb didn't help I had hoped to save you the $. Speaking of $, a timing light that will serve your needs is less than $20. I have a 2100 top cover identicle to yours but both cast bowl vents are intact. It's yours free if you want it. By running a hose from the carb side of the fuel filter to a glass jar you can crank the engine to see if the fuel is getting to the carb. A pulsing flow into the jar is good. A trickle means there's an obstruction. My pickup screen got plugged by dirty gas at a station that was just refilled. It resulted in a time consuming removal and flushing of the main tank.
The point ignition wouldn't cause your symptoms, but if you later want to upgrade to a transistorized system go with the better quality Duraspark. We still don't know if the problem is too little fuel, too much, spark to wrong plug, really bad timing, etc. Fuel coming out of the bowl vent is a problem even with the tube broken off. Many 2100,2150s had very short bowl vents. Especially those made for 4x4 trucks.
Before investing in new parts it's better to get a few far cheaper diagnostic tools and a trouble shooting book. They will save you money in the future too.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Not too surprising the new carb didn't help I had hoped to save you the $. Speaking of $, a timing light that will serve your needs is less than $20. I have a 2100 top cover identicle to yours but both cast bowl vents are intact. It's yours free if you want it. By running a hose from the carb side of the fuel filter to a glass jar you can crank the engine to see if the fuel is getting to the carb. A pulsing flow into the jar is good. A trickle means there's an obstruction. My pickup screen got plugged by dirty gas at a station that was just refilled. It resulted in a time consuming removal and flushing of the main tank.
The point ignition wouldn't cause your symptoms, but if you later want to upgrade to a transistorized system go with the better quality Duraspark. We still don't know if the problem is too little fuel, too much, spark to wrong plug, really bad timing, etc. Fuel coming out of the bowl vent is a problem even with the tube broken off. Many 2100,2150s had very short bowl vents. Especially those made for 4x4 trucks.
Before investing in new parts it's better to get a few far cheaper diagnostic tools and a trouble shooting book. They will save you money in the future too.

Thank you for the input. I keep thinking that I've got it narrowed down to a certain part so I assume I must need a new one. That methodology has not been very successful thus far. My plan for the next step is to do a compression test, check fuel flow, check spark, timing and coil tomorrow. Hopefully that gives me some much needed information. I don't think I'm leaving anything out.
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
When you stabbed the distributor did you get it in 100% correct. Or was it in the motor when you git it?. You could be a tooth off or more. When I put a motor in I never take a po word for anything. I replace all wear items ( plugs, wires, cap rotor, points, coil, etc.) I set a baseline timing ( I have stabbed a distributor wrong more than once) it easy to tell when your 180 degrees out but a couple teeth is harder cuz it will run but will run really shitty.

The motor should be at 10* BTDC. Pull the#1 spark plug and put your finger in the hole and feel for the up stroke. The rotor should be pointed at the 1 cylinder on the cap.. search on here fir a more detailed description.
 
Last edited:
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I had someone more knowledgeable than me stab the distributor but who knows. I'll check it out as well.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Well guys... Let's hold the laughter to a dull roar and remember that I am not the most experienced mechanic around. That being said.

The new 302 is an H.O. and I had it set up for a regular 302 firing order. switched it over and set the timing and well, she runs. Accelerator pump isn't working on the new carb and that's causing some issues but she runs!
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Well at least you took care of the main issue. Now just the little stuff to get it runnig like a top.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Yeah the big thing is taken care of now just some tuning i believe. One thing I dont get is I still can see gas coming out of the right vent tube of the carb at 3/4 throttle ish...could I be pumping too much gas? I switched to an electric pump. supposed to be 4-7 lbs
 
Top