• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gauge help...

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Riddle me this:

I just put a brand new temp gauge in my cluster, hooked it up, and now none of my gauges work.

Just recently replaced the IVR too - so I know it's fine.


Update: I reversed the connections and it pinned all the gauges.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
Update: I reversed the connections and it pinned all the gauges.
Reversed the connections on what?

Put it back the way it was and disconnect the temp gauge from the IVR and see if the oil and fuel gauges go back to working.
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Reversed the connections on the temp gauge.
Disconnecting the temp gauge makes everything work again.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
What happens if you hook up just the power but not the sensor to the temp gauge? Try both posts of the gauge that way (being a thermal gauge polarity shouldn't matter, but a short on one post will show up).

You do have the gauge cluster grounded while trying this, right? If you have the gauges out of the dash it isn't grounded. The gauges ground through the gauge mounting screws to the dash, you need those or at least a temporary ground to the dash.
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Well, now something's gone really haywire... !!

When I hook up just the power to the temp gauge, they all pin.
When I disconnect the power wire to the temp gauge, they all pin.
When I hook up the sensor wire to the temp gauge they all go flat.

So basically, I have no normal operation of the fuel or oil anymore in any combination. ?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Well, now something's gone really haywire... !!

When I hook up just the power to the temp gauge, they all pin.
When I disconnect the power wire to the temp gauge, they all pin.
When I hook up the sensor wire to the temp gauge they all go flat.

So basically, I have no normal operation of the fuel or oil anymore in any combination. ?

Do you have the cluster grounded to the body? Lack of proper ground will do that.
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Cluster is grounded (according to my test light and meter).

Which gave me the idea, to check the temp gauge connectors...
The power pole on the temp gauge (that goes to the IVR) is showing ground ?:?
So, I think that the gauge may have been NFG/DOA out of the box, and blew my IVR which is now causing all my other gauges to go haywire.

Opinions?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Cluster is grounded (according to my test light and meter)...

I could be wrong, but I don't think you can use a test light or a meter to check for sufficient ground on a dismounted cluster. You'll get a path through one or more wires to light the light and trick the meter, but your cluster is NOT grounded until it's case is connected to the dash.
Or a jumper wire to ground for testing purposes of course.

Stock wiring harness, or aftermarket?

Paul
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
It's screwed back into the dash and grounded. Checked with a continuity meter.

Aftermarket harness. The sensor wire goes straight to the temp sensor.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Gotcha. Well, that's a strange one then.
Sounds like you were on to something with the gauge stud showing a connection to ground.

Hopefully the experts will chime in.

Paul
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Well,like I said, I'm starting to think I may have gotten a bad gauge that blew my IVR... which sucks, cause I may be able to return the gauge, but the IVR is $40-ish and ultimately puts me out about $100. Boo.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Which gave me the idea, to check the temp gauge connectors...
The power pole on the temp gauge (that goes to the IVR) is showing ground ?:?
So, I think that the gauge may have been NFG/DOA out of the box, and blew my IVR which is now causing all my other gauges to go haywire.

Opinions?

If the wires are unhooked and you read a short to ground, bad gauge.
If the wires are still hooked up, may be OK as the power wire can be backfeeding a ground from the other loads that are not being powered.
 
OP
OP
derol

derol

New Member
Joined
Mar 8, 2010
Messages
30
Loc.
Santa Cruz
Well, there's yer problem right there...

temp-gauge.jpg
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Know the feeling. Had the same issue with fuel gauge going to ground burnt gauge and IVR. So I went a different route with gauges. Got the mechanical ones from Auto Meter with volt gauge and universal fuel gauge and universal sender all for around 100 bucks. Got rid of IVR.
 
Top