• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

darting right under acceleration

Labbster

Sr. Member
Joined
Nov 19, 2003
Messages
755
Almost peed my pants the other day. Bronco drives great, but when under hard acceleration it darts right. When letting off the gas it darts back left. And she darts in a HURRY! Would this be from Axle Wrap? Any suggestions?

I have the BC broncos 3.5 lift from at least 7 years ago but it is a new install. Tie rod over. 7 degree c bushings.

It drives down the road great. no wondering at all when going over bumps. Just scares the poop out of me on full acceleration. Has roughly 350 - 400 hp. 351 efi gt40 aluminum heads.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
I think darting on hard acceleration would be something in the rear end , if it drives normally all the other times . Are the leaf spring bolts tight are the u bolts tight . I would check that first.
Did it happen all of a sudden you could have a broken spring
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
What kind of differentials... Open, LS, or locked? Could be something in there taking it left / right under acceleration.


DJs74
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
That started happening to me when I replaced the C4 with a NV3550. It was quite scary to have one hand on the wheel and the other on the shifter and practically change lanes on its own during the shift.
It's called "bump steer."
I ended up replacing the pitman arm with a dropped one for the cure.;)
 
OP
OP
Labbster

Labbster

Sr. Member
Joined
Nov 19, 2003
Messages
755
I thought the tie-rod over would take care of the bump steer? Also, I do have a locker in the rear. All other bolts are new and tight.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Leaf spring front bushings. Something to check. allows the axle to shift forward under load. A little bit of rear steer on a short wheelbase can get wild. We are talking fractions of an inch deflection under load.
 

NicksTrix

Bronco Guru
Joined
Aug 1, 2001
Messages
6,410
are your spring hanger holes still in good shape. i've come across many that are chewed up allowing the spring to move like broncobowsher mentioned
 
OP
OP
Labbster

Labbster

Sr. Member
Joined
Nov 19, 2003
Messages
755
I will inspect again when home, but I thought everything was in really good shape when I installed the lift
 
OP
OP
Labbster

Labbster

Sr. Member
Joined
Nov 19, 2003
Messages
755
That's why I originally thought it was due to axle wrap because she squats like crazy under accelerate. And the springs have dropped so much I had to add 1.5 blocks. However, I have a 37 spare and huge bumper too
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Might also be a bit of bumpsteer from the front suspension unloading so much on hard accels. Any roads with straight across dips you can take aggressivly?
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
check em.......mine was doin Same~ish kinda stuff they were gone
 

broncoman1972

Bronco Guru
Joined
Mar 4, 2004
Messages
1,300
If the trac bar bushings are good as mentioned above I'd suspect the rear axle. Check the springs and u-bolts as mentioned. If you have a locker and did any recent wheeling or drag racing:cool: you could've broken an axle. I had one slowly twist off at the splines. It was a clean break and drove fine even at 50 mph but it would pull hard one way on accel then the other way on decel.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Swap left and right rear tires. If it starts going left instead you have a tire issue
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I thought the tie-rod over would take care of the bump steer?

Yes and no. Depends entirely on how it was done, and how the rest was modified to match. What was done to the trackbar?


Also, I do have a locker in the rear.

A locker can easily cause what you're describing. Drove a friend's with high lift, 35" tires and an NV4500 trans. It would shift side to side just when shifting. The act of pushing in the clutch while accelerating would cause it to swap lanes! Yours does not sound quite as bad, but similar.


...but I thought everything was in really good shape when I installed the lift

So it did not do it before the lift, but does it now? Could it be all new, or could it possibly just be more pronounced?
A lift can do it both ways again. Could be steering linkage related, but it could simply be that the locker (or something else at the rear of the truck) is now just reacting too much. (see below)


That's why I originally thought it was due to axle wrap because she squats like crazy under accelerate. And the springs have dropped so much I had to add 1.5 blocks. However, I have a 37 spare and huge bumper too

Well there 'ya go...
Squatting like crazy can possibly move the suspension through a larger cycle than simply hitting bumps would. Combination of squatting in the back and lifting in the front is much more pronounced than just hitting bumps is. Very possible then to still be things related to bumpsteer, but way more pronounced during accel/decel action.


going over dips and bumps she stays straight and true.

That's a good sign anyway. Means that the setup is at least decent. But still could be experiencing exaggerated motions with all that power on tap, trying to push 37" tires around.
What gear ratio do you have? That makes a big difference sometimes in how a rig squats under accel. With a weak stock motor, not so much. But with your higher output pushing against said gears and tires, it could be enough.

What type of steering linkage are you running? Can you post up some images of the layout?
Regarding the rear, Broncos in general, and aftermarket springs in particular can wrap something fierce under your conditions. If you're running good power and big tires, and have fun with the go-pedal, then you need to think like a street racer rather than a moderately modified trail crawler, and do something in the traction department. We sell our Wrap-Trap, but there are lots of products out there to reduce axle-wrap. Sounds like no matter what the side-to-side shifting issue turns out to be, you're going to need some anti-wrap device installed.

Have fun. Post up some pics when you can.

Paul
 

tacobronco

Jr. Member
Joined
Nov 15, 2011
Messages
97
I had BC broncos 3.5 leaf springs of that same vintage, and they did the exact same thing (though maybe not as severe as the OP describes). Later switched to WH 4.5 springs for unrelated reasons, and they don't do it at all. I always just assumed it was the BC springs wrapping. I used the same bushings, shackles, and hardware on both sets, so nothing else really changed. Nothing against BC, just seems like the WH springs are just as flexy without the wrap. Can't explain why - they look like very similar designs.
 

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
mine did that,

toook me forever to find the problem,
the axle pads were worn on the ends,

lets the axle wrap a little and usually only does it on one side.

Id remove the U bolts, drop the axle and put a quality straight edge on the pads.

the centering pins will also be worn, and maybe the holes in the pads,

I just made new plates out of thick metal , like 3/8 I think, and drilled holes in them and welded them on top of the old pads
 
Top