Hey BroncoSport. Here are a couple of observations from your description and pic. (thanks for the pic by the way!)
It just seems that it could shoot off the road if I turn too fast or hit a road groove. It doesn't go in any direction when accelerating, but it does pull somewhat to the side when braking. It used to do it a lot more before I had the brakes rebuilt.
It can still very easily be partially due to brakes. By the looks of it, still drums all the way around? If so, you're going to need to be come intimately familiar with the adjusting procedure. As you may have read around here already, the automatic adjusters do not always automatically adjust.
And on a lifted short wheelbase rig like ours, all four corners have to be adjusted very, VERY(!) closely to the one on the opposite side. Front and back don't have to be exactly like each other (although it certainly helps in overall feel) but side to side adjustments need to be very close, if not exact.
I'm afraid to try an emergency lane change.
Just out of curiosity, how does it handle overall? Feeling wishy washy when maneuvering? Might be weak shocks?
You also might be dealing with wheel backspace issues with your larger tires. But we'll get to that later.
Like the OP, I also have a 2/5" suspension lift, 1" body lift and 33"x12.5" tires, but I have 28psi all around.
I doubt this is the root cause of any of your issues, but I would still experiment with tire pressures anyway. And because our rigs are not 50/50 balanced, nor are they typically loaded equally, and it's now modified from stock anyway, you might as well start fiddling around with pressures.
Let us know exactly what tires, what condition, and what max-press ratings are on the side. But don't hesitate to go as low as 25 in the rear and as high as max press in the front. While I usually find that about 30 works best there, I've run them in a very wide range.
The Previous owner did the 2.5" lift. I can see my drag link grease fitting is at a 45 degree angle and I think I have the trac bar drop bracket, although it's not welded.
Yes, trackbar drop. And yes, it should be welded. But not yet...
Your grease fitting angle is correct because this looks like stock factory linkage. It's only when that gets changed to the fully adjustable type that we need to worry about that angle.
I originally bought a drop pitman arm, but it seemed the steering shock was at such an angle compared to the bracket, so I put the stock pitman arm back on. And I think that's correct, guessing by the parallel appearance of the arms.
Well, maybe not. Under most situations, a '71 with a drop bracket on the trackbar MUST use a dropped pitman arm in conjunction. Forget the angle of the stabilizer shock. It's by far the least important aspect of your steering geometry, and should never be favored over something more important.
For the angle, you're correct that it does look pretty good for now. But imagine a straight line through the pivot points and see if the two bars are still parallel. For us here, you'd have to remove the steering stabilizer and shoot another image so we can see the two better.
And if you don't mind, that would be great. Or at the very lease, post up an image taken from slightly farther to the driver's side so we can see the upper draglink mount more clearly.
I definitely have play in the steering wheel, which is what I was initially searching for, but thought my setup and the OP's setup was so similar, I thought I'd post here.
That's fine. It's a good way of getting more attention to your plight while not getting off-topic for the original poster. Works for me!
You're going to have to do the big test that we talk about over and over again. It's something that should be performed any time there is some funky motion going on with the steering. It'll highlight any looseness in any part of the system that ends up at the steering wheel. More later...
I also read that the pitman should be on slightly towards the driver wheel when centered. I definitely didn't do that. Is that something to be worried about?
Maybe. Maybe not...
Original manual steering gears, and possibly some early power setups were offset to one side when centered. But very quickly the power steering setups were re-oriented so that, when the steering box is on-center, the pitman arm is straight back down the frame.
Even your minimal lift can have an effect on this, which might even be exaggerated by the use of only the drop bracket without the pitman arm.
Personally, I would remove the upper draglink end from the arm, OR pitman arm from box, and start from scratch with centering the box. But I'd also do "The Test" (before or after) to see what's up with the excess play.
At the very least, you're going to need either/or/both the dropped pitman arm and the adjustable draglinks that are now available. In theory the pitman arm drop should take care of that, but the adjustable link helps fine-tune things.
OR... And here's the other "OR" of this setup. Since your drop bracket is not welded on at this time, you might consider removing it to see if it helps things. If it does, then you know we're on the right track. Whether the "best" way to run is with it again, or without it, will depend on how it feels on the road.
Is this your first older truck by any chance? How much play is present in the steering wheel? Usually these old trucks and utility vehicles have more play than a modern counterpart, which is why I asked.
If you don't find reference to the test, or how to verify the steering box is in it's on-center position when the wheels are pointed straight, let us know and we can describe it to you in detail.
Basically though, the test is where a helper turns the steering wheel back and forth while the tires are fully on the ground and you're watching underneath for any excess play.
I can virtually guarantee you'll see some rocking motion with the trackbar mount, and perhaps some rod ends, and bushings here and there, and maybe wheel bearings or ball-joints or yokes in the steering column-to-box input shaft, and etc, etc, etc.
It all adds up.
Good luck. Let us know if any of that will work for you.
Paul