I don't understand electricity in the least bit so I'm not following a lot of these grounds instructions.
Not to worry. Very few get the whole picture right off the bat. Takes one of those "aha!" moments usually. Kind of a Ford Better Idear Light bulb kind of a moment. Except that light bulb needs to have a ground to work!
Just think of every electrical bit on a vehicle as needing a full LOOP. For simplicity's sake, there is the power (12v+), the "load" (whatever is being powered) and the ground return (12v-). There's something about the power actually flowing FROM the negative TO the positive, but we'll let the brains clear that one up for us.
For an electrical load to work, it has to have a clean full path to and from the battery, and has to have some built-in resistance to that flow to keep it from being a "short-circuit" (literally a direct path to ground with insufficient resistance) and cause all kinds of other mischief.
So when we say all Early Broncos need more grounds, it's because Ford only installed enough to barely get the job done back when everything was new and all the sheet metal bits conducted electricity like you would expect. Only now it's 40 to 50 years later, with the rust, paint and other separating factors that come along with old age. So your electrical LOOP is compromised but the power still wants to get back to the battery to complete it's journey.
If it can't find the easiest path back, it'll try to find any other one. This includes anything that still conducts electricity like other metal parts, a smaller wire, a wire that might normally be for the positive side that just happens to not be in use at the moment, or even the coolant in the radiator.
Your little reference connection wire was just in the wrong place at the wrong time.
Unless it's somewhere else, the only thing I saw concerning battery cables and grounds was the one single cable that went from the negative post to the engine. I replaced that but we're should I like for a frame ground wire?
So you already were dealing with a ground cable that had been replaced in the past. As most have by now. Maybe even more than once.
The original negative battery cable as delivered from Ford included a bonded clamp (means that it was part of the conductor) that was attached to the sheet metal of the wheel well. If you look, you'll see a small hole (#12 or 1/4" maybe?) in the wheel well adjacent to the alternator.
You can run a 10ga wire between the battery negative terminal and that hole if you want, or simply run the wire to one of the bolts that holds the starter relay to the wheel well.
This will at least get you started down the grounding path to nirvana.;D
I only ran my negative ground coming from the battery to the side of the engine block. There looked to be only one negative cable and it was to the block
That's the main one of course, since the largest load on a typical vehicle is the starter. But add the one I mentioned above and you're well on your way.
Add the one the others were talking about too, which would be from the back of the intake manifold area to the firewall. Most other vehicles have one of these, and Broncos should have had, but didn't.
This new one will help your dashboard and all it's functions work better by "bonding" (there's that word again) to the rest of the ground system.
Would the ground like pictured above by my regulator count as a body ground of some sorts since it's basically bolted to the body on one end and the alternator at the other end?
Good thinking, but as Viper said, it's not a legit body ground. If for no other reason than it's not large enough in the first place. Remember it's got to pass whatever positive voltage is left after the "load" is through with it, back to the battery. So it's too far away (resistance) and too small (more resistance) to do anything other than what it's intended to do.
Also could I run a strap from the same point on the block I have my neg battery cable bolted to from there to the frame or need be a different spot on the block? Basically one ground ending and one ground starting from the same point?
Yep. Perfect and probably as easy as it gets, which makes it better. Nothing wrong (in general terms) with putting it somewhere else, but adding it to the same spot guarantees a better connection potential.
That's for the frame though, which really doesn't need much (but should still be part of the system) because not much normally passes through the frame. Nothing says you couldn't add that other one to the firewall I mentioned earlier, to the same spot. I just mentioned the back of the intake manifold because it's more convenient and looks cleaner and stays away from exhaust. All good things.
Oh, and speaking of resistance, the larger the gauge/size of wire, the more current it can pass safely and over a longer distance. Since the starter motor is a big load, and you don't want to overload things, overkilling the battery and starter cables is standard practice nowadays.
The factories used to use 6ga cable and even the occasional 8ga(!) cable for their purpose. We typically talk about a minimum of 4ga with 2ga being better, and 1, 0, and 1/0 or 2/0 welding cable as being good for battery cables. Overkill? Yep. Just enough? You bet!
At Wild Horses we use 6ga for the alternator charging cable and 2ga for the battery and starter cables. Minimums these days.
Hope all that wasn't just blah blah blah to you. A lot of new concepts to bandy about in your brain, but maybe some of it will stick and it won't be so intimidating later.
Good luck!
Paul