• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Voltage reg ground wire help

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
I need to rerun the ground wire coming from my voltage regulator as it is completey bare. It's taped up with another set of wires that looks to be running to the alternator or somewhere. My ground is a red and black wire. Where does it run to? I want to take it and the rest of the wires coming from regulator off and replce the ground and rerun them all. Here is what my ground looks like
Any thoughts on why this happened to begin?

 
OP
OP
T

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
I need to add that I replaced my solenoid and battery cables yesterday and my positive cable coming from solenoid to starter was as bare as ground on regulator about a third of the way off the starter back toward the solenoid.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
That ground wire should run the the alternator. You need to check your other ground wires too, looks like maybe your main ground wire is bad and it's trying to ground through that small ground wire and overloading it.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
That wire overheated & melted its insulation off; probably due to poor grounding somewhere along the main negative path from the alternator case to the engine bracket to the head to the block to the (-) cable. Click these & read the captions:

. . . .

When the main path is interrupted (due to loose connections, corrosion, or improper assembly), the current will try to flow any way it can. And that little wire isn't big enough to handle the load - it's only intended to be a reference voltage for the regulator. Look at zones C-H1 in this diagram:



The starter positive was probably bare due to the (cheap) insulation shrinking from normal engine heat. Buy better wire & cables.

 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I would double check all the wires while you're digging around. But as said, replace any battery and starter cables that look suspect at all.
Frankly, they're cheap so if in doubt, some new fatties are called for.

Your original ground wire from the voltage regulator runs to the alternator case, as the others have said. But it was not an easy to see path until you remove the alternator and look at the backside connections. Your original connector there is a molded affair with all the wires coming through it, but the ground at that point is simply a metal loop that looks like it's just a mounting clamp for the molded connector. Because that's what it is, but the ground wire is attached to it inside the rubber insulator where you can't see.
So if your alternator's harness is buggered up there too, either replace it with a new one or make your own with all 3 (or 4 in your case most likely) wires.
Your '74 most likely has an electric choke for the carburetor, which uses a White w/black wire from the STA terminal on the back of the alternator.

While we're discussing grounds, your original negative battery ground wire would not only have connected to the engine block, but would also have had a junction to the body. Most people leave this body ground off when replacing with aftermarket ground cables.
You'd do well to add one to yours if you don't already have it.

Paul
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
That ground wire should run the the alternator. You need to check your other ground wires too, looks like maybe your main ground wire is bad and it's trying to ground through that small ground wire and overloading it.

X2 what he said. Looks like it became your primary ground at some point and overheated. It should go all the way back to the alternator.
 
OP
OP
T

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
I only ran my negative ground coming from the battery to the side of the engine block. There looked to be only one negative cable and it was to the block
 
OP
OP
T

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
I don't understand electricity in the least bit so I'm not following a lot of these grounds instructions. Unless it's somewhere else, the only thing I saw concerning battery cables and grounds was the one single cable that went from the negative post to the engine. I replaced that but we're should I like for a frame ground wire?
 

kip60

Full Member
Joined
Feb 7, 2015
Messages
239
As others have stated, good grounds are imperative for a good electrical system. The battery does ground to the block with the negative cable. With the age and rust issues these rigs have, it is a good idea to take that ground even further. You need to take a grounding strap(attached) and ground the block to the body. Then take another and ground the body to the frame. These just make the whole electrical system work better.

http://www.oreillyauto.com/site/c/s...&model=Bronco&vi=5157899&keyword=ground+strap

PS: It doesn't really matter where the straps are located as long as there is good metal to metal contact between everything. Using a good electric grease helps keep everything cleaner longer.
 
OP
OP
T

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
Would the ground like pictured above by my regulator count as a body ground of some sorts since it's basically bolted to the body on one end and the alternator at the other end?

Also could I run a strap from the same point on the block I have my neg battery cable bolted to from there to the frame or need be a different spot on the block? Basically one ground ending and one ground starting from the same point?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Would the ground like pictured above by my regulator count as a body ground of some sorts since it's basically bolted to the body on one end and the alternator at the other end?

Also could I run a strap from the same point on the block I have my neg battery cable bolted to from there to the frame or need be a different spot on the block? Basically one ground ending and one ground starting from the same point?

The black - red wire is not a body ground. It's there to reference the voltage regulator ground as close to the alternator ground as possible. It can't take much current. You should have a heavy body ground between the rear of the intake and the firewall. If the body ground fails or is removed all the electrical current from all the accessories will try to go through the black - red wire and smoke it.

Yes, you can run a ground to the point as the negative cable.
 
OP
OP
T

Trappey74

Full Member
Joined
Sep 22, 2015
Messages
303
Loc.
Cleveland
I followed the cable cluster and the ground coming from the voltage reg down to the back of the alternator. How do I unhook this bundle of wires from the back of the alt. I have the under dash air and the compressor is in the way too kind of
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
There is a bolt or stud that holds the ground terminal at the bundle. Then you have the other wire connections too.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
These trucks weren't built with good wiring, and at this age, it really shows. If you want to have the least trouble in the future, start by rebuilding the battery cables now, and routing them for the best performance.

The positive is pretty easy: start at the CLEAN battery (+) post; use a hard (not Lead) terminal clamp SOLDERED to a good red cable (4ga is enough for stock and most mods) going to either big post of the starter relay (the new style is vastly superior). If you use a "mini" starter (any starter with a solenoid), the positive cable should continue (UNcut) to the starter solenoid's top post; but if all the terminals are clean, it's OK to run a 2nd (separate) cable from the relay to the solenoid (the battery & starter cables' terminals should be adjacent on the relay post). If you run a winch, SOLDER a 2nd cable (4ga or 2ga) into the positive clamp on the battery.

The negative ("ground") cable needs to hit a few more things, but it starts the same way: a hard clamp soldered to the same-size black cable as the positive. Solder a flag terminal around the UNcut cable such that it can be bolted to a factory hole in the frame rail (not a crossmember) where you can clean the rail down to shiny steel. The block ground should also be cleaned down to shiny cast iron. If you run a winch, increase the negative cable to 2ga and continue it from the block to the winch motor negative (any winch over ~3K will have one). An ~8ga body ground wire should also be soldered into the battery clamp going to a shiny spot on a panel welded to the body tub (like the inner fender where the VR ground wire is).

If you don't want to build your own battery cables, those found on ~'90-96 F-series & Broncos are nearly a perfect fit, and they can sometimes be found in decent condition in JYs for a few bucks.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I don't understand electricity in the least bit so I'm not following a lot of these grounds instructions.

Not to worry. Very few get the whole picture right off the bat. Takes one of those "aha!" moments usually. Kind of a Ford Better Idear Light bulb kind of a moment. Except that light bulb needs to have a ground to work!

Just think of every electrical bit on a vehicle as needing a full LOOP. For simplicity's sake, there is the power (12v+), the "load" (whatever is being powered) and the ground return (12v-). There's something about the power actually flowing FROM the negative TO the positive, but we'll let the brains clear that one up for us.
For an electrical load to work, it has to have a clean full path to and from the battery, and has to have some built-in resistance to that flow to keep it from being a "short-circuit" (literally a direct path to ground with insufficient resistance) and cause all kinds of other mischief.

So when we say all Early Broncos need more grounds, it's because Ford only installed enough to barely get the job done back when everything was new and all the sheet metal bits conducted electricity like you would expect. Only now it's 40 to 50 years later, with the rust, paint and other separating factors that come along with old age. So your electrical LOOP is compromised but the power still wants to get back to the battery to complete it's journey.
If it can't find the easiest path back, it'll try to find any other one. This includes anything that still conducts electricity like other metal parts, a smaller wire, a wire that might normally be for the positive side that just happens to not be in use at the moment, or even the coolant in the radiator.
Your little reference connection wire was just in the wrong place at the wrong time.

Unless it's somewhere else, the only thing I saw concerning battery cables and grounds was the one single cable that went from the negative post to the engine. I replaced that but we're should I like for a frame ground wire?

So you already were dealing with a ground cable that had been replaced in the past. As most have by now. Maybe even more than once.
The original negative battery cable as delivered from Ford included a bonded clamp (means that it was part of the conductor) that was attached to the sheet metal of the wheel well. If you look, you'll see a small hole (#12 or 1/4" maybe?) in the wheel well adjacent to the alternator.
You can run a 10ga wire between the battery negative terminal and that hole if you want, or simply run the wire to one of the bolts that holds the starter relay to the wheel well.
This will at least get you started down the grounding path to nirvana.;D

I only ran my negative ground coming from the battery to the side of the engine block. There looked to be only one negative cable and it was to the block

That's the main one of course, since the largest load on a typical vehicle is the starter. But add the one I mentioned above and you're well on your way.
Add the one the others were talking about too, which would be from the back of the intake manifold area to the firewall. Most other vehicles have one of these, and Broncos should have had, but didn't.
This new one will help your dashboard and all it's functions work better by "bonding" (there's that word again) to the rest of the ground system.

Would the ground like pictured above by my regulator count as a body ground of some sorts since it's basically bolted to the body on one end and the alternator at the other end?

Good thinking, but as Viper said, it's not a legit body ground. If for no other reason than it's not large enough in the first place. Remember it's got to pass whatever positive voltage is left after the "load" is through with it, back to the battery. So it's too far away (resistance) and too small (more resistance) to do anything other than what it's intended to do.

Also could I run a strap from the same point on the block I have my neg battery cable bolted to from there to the frame or need be a different spot on the block? Basically one ground ending and one ground starting from the same point?

Yep. Perfect and probably as easy as it gets, which makes it better. Nothing wrong (in general terms) with putting it somewhere else, but adding it to the same spot guarantees a better connection potential.
That's for the frame though, which really doesn't need much (but should still be part of the system) because not much normally passes through the frame. Nothing says you couldn't add that other one to the firewall I mentioned earlier, to the same spot. I just mentioned the back of the intake manifold because it's more convenient and looks cleaner and stays away from exhaust. All good things.

Oh, and speaking of resistance, the larger the gauge/size of wire, the more current it can pass safely and over a longer distance. Since the starter motor is a big load, and you don't want to overload things, overkilling the battery and starter cables is standard practice nowadays.
The factories used to use 6ga cable and even the occasional 8ga(!) cable for their purpose. We typically talk about a minimum of 4ga with 2ga being better, and 1, 0, and 1/0 or 2/0 welding cable as being good for battery cables. Overkill? Yep. Just enough? You bet!

At Wild Horses we use 6ga for the alternator charging cable and 2ga for the battery and starter cables. Minimums these days.

Hope all that wasn't just blah blah blah to you. A lot of new concepts to bandy about in your brain, but maybe some of it will stick and it won't be so intimidating later.

Good luck!

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
All that crap above is why some Broncos these days have dim headlights even after you've put in new ones and even new wires in some cases.
The "ground" in this case is the radiator core support sheet metal that's welded to the inner fender aprons, which are in turn welded to the wheel well, where the battery-to-body ground is supposed to be.
Even with a new negative wire from the battery to the wheel well, that welded contact can be rusty and have paint intruding on the seam, which adds resistance enough to keep enough power at bay that the lights can't get a full 12v to work properly.
Here, rather than remove and clean and re-weld the entire panel, a new small length of 10ga wire between the core support and a known-good grounded bit of metal (your wheel well when it's wired in like described above) will work wonders.
Basically bonding the core support to the rest of the grounded bits of the body.

Simple as mud, eh?
It's just another pathway in the big loop.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Didn't see Steve's post before sending mine. Always good info there, especially the factory wiring when you can get it from the junkyard.
I don't mind using even the cheap store-bought stuff myself. It's got good quality wire and good crimps, but I still add sealed shrink tubing at the ends to keep the weather and battery acid out of the conducters and on the outside of the jacket where it belongs.

In cases like the starter cable where it runs over and around stuff, and close to the exhaust, I even add the split-loom like the factory does to protect it a bit more.

Paul
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
If the cable is soldered into the battery clamps, acid & weather won't affect the terminal-to-wire connection, and heat-shrink isn't needed. If it's crimped, only marine heat-shrink will do any good, and I haven't seen it commonly available in 4ga or 2ga size. So if you buy cheap aftermarket crimped cables, I recommend soldering them while they're new & clean.

The rust that gets into the spot-welded seams in the factory body doesn't affect the actual weld spots where electricity is conducted. So corrosion there doesn't cause resistance until so much of the steel is gone that the body is falling apart. But the rust all over the panels DOES interfere with the wire connection because no one bothers to clean the "original" paint off (& the rust under it) before attempting to tighten a ground wire bolt onto the old sheet metal. But adding a system of negative wires around the truck (like modern vehicles have) will certainly help, as long as they're sized properly. Going big is safe but expensive, heavy, & bulky.
 
Top