• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Is my bronco overheating?

OP
OP
flexmerc

flexmerc

Full Member
Joined
Oct 9, 2014
Messages
250
Fan purchased, I'll keep y'all updated!
I preparing for a spacer to clear the AC condenser, thanks guys!
 

sanndmann3

Contributor
Bronco Guru
Joined
Jun 13, 2007
Messages
1,832
I used to run this fan back when I had V belts. It pumps some cfm, should cool you down for sure.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Good call on the fan size Justin. That's crazy!
Not that this is the same situation since you have to have all the other stuff to run one, but I spent a lot of time yesterday driving in 100-102 degree heat with the A/C on the whole time and the temp sat right at a tick over 195 the whole time.
Speeds from 5, up to 75 mph with no change. The higher speeds are often where EB's generate a lot of heat, but can't seem to dissipate it quick enough. No problem this time.

That's more by way of comparison perhaps, than anything really helpful to someone with a V-belt setup. Hopefully the bigger diameter fan will get rid of any issues 100% and you won't have to worry about it anymore.

Good luck!

Paul
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
flexmerc,
Another thing to consider, once you get the fan ironed out, is the idle speed. It needs to be fast enough to keep both the air flow and coolant flow up. That can be a bit of a problem sometimes with an automatic transmission. If the idle is set too fast, the torque converter will start building up heat as well. You're aiming for the "sweet spot." My valve cover decal called for 650 RPM with the tranny in gear.
 
OP
OP
flexmerc

flexmerc

Full Member
Joined
Oct 9, 2014
Messages
250
Alight guys I bought a laser temp gun and a Mr Gasket Rad cover w/temp guage.

1.) I drove the truck at highway speeds (50-60) and stop/go traffic for 20 minutes.
2.) Then ran the truck idle in the parking lot for about 20 minutes..then started temp testing
3.) "Testing" was done 10 minutes apart....

I still need to get the larger fan, better safe than sorry....but i feel like i may be over thinking it.

I am
 

Attachments

  • 1 gauge.jpg
    1 gauge.jpg
    60.4 KB · Views: 126
  • 2 Thermo Hose.jpg
    2 Thermo Hose.jpg
    87.2 KB · Views: 115
  • 2 thermo hose 2.jpg
    2 thermo hose 2.jpg
    106.8 KB · Views: 104
  • 2 Mr Gasket.jpg
    2 Mr Gasket.jpg
    66.4 KB · Views: 119
  • 2 gauge.jpg
    2 gauge.jpg
    51.7 KB · Views: 126
  • 1 Thermo Hose.jpg
    1 Thermo Hose.jpg
    75.2 KB · Views: 105
  • 1 Mr Gasket.jpg
    1 Mr Gasket.jpg
    67.9 KB · Views: 125
  • 1 Intake Sensor.jpg
    1 Intake Sensor.jpg
    75.3 KB · Views: 148

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Point the guns at the thermostat housing and at the top of the radiator where the upper hose attaches.
 
OP
OP
flexmerc

flexmerc

Full Member
Joined
Oct 9, 2014
Messages
250
Temp was when I shut the vehicle off and let it set for about 5 minutes....
I do not have a body lift and the AC photo is for the guy who asked....

I do not understand how the AC has a different requirement for cooling or affects pressure....
 

Attachments

  • Water Pump w AC Comp.jpg
    Water Pump w AC Comp.jpg
    103.2 KB · Views: 112
  • AC Compressor.jpg
    AC Compressor.jpg
    68 KB · Views: 104

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
It has a different requirement because you have to pull air through the a/c core. And the increased performance from a proper fan will not just further cool your vehicle rad it will also better cool your a/c core in front of your rad.

And wow....your fan is way inside your shroud. That's no bueno. You want about half in half out or around there, but all the way in ain't good homie.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Look at the compressor clutch in the photo. It's in the way of the fan. This is exactly what Vintage Air tried to sell me. It would be impossible to put an affective fan in that space. I had them fabricate me a bracket that move the compressor out 4 inches.
Don't let them off the hook for this.
 

Attachments

  • AC%20Compressor.jpg
    AC%20Compressor.jpg
    68 KB · Views: 101

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Look at the compressor clutch in the photo. It's in the way of the fan. This is exactly what Vintage Air tried to sell me. It would be impossible to put an affective fan in that space. I had them fabricate me a bracket that move the compressor out 4 inches.
Don't let them off the hook for this.

Yes, but BC's is only a little better Blu. Both VA and BC should have followed your lead....cause that ain't a kit when you have to run a damn 14" fan....
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Here's what Vintage air made for me after I complained. The bracket moves the compressor four inches to the passenger side. It works great!
 

Attachments

  • IMG_20170708_100217203.jpg
    IMG_20170708_100217203.jpg
    64 KB · Views: 104

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Check the temperature on the radiator tank where the hose goes in on the drivers side and then check the temperature at the radiator tank on the passengers side where the hose attaches. While running and fully warmed up. This will tell you how much heat you are actually displacing. Then do this again when you get your fan figured out. Is there a phyiscal reason you cant push the air compressor back and run on the outside pulley groove? I'm sure you would have to deal with new brackets. It is possible to run a shorter single groove pully and clutch.
 
OP
OP
flexmerc

flexmerc

Full Member
Joined
Oct 9, 2014
Messages
250
Check the temperature on the radiator tank where the hose goes in on the drivers side and then check the temperature at the radiator tank on the passengers side where the hose attaches. While running and fully warmed up. This will tell you how much heat you are actually displacing. Then do this again when you get your fan figured out. Is there a phyiscal reason you cant push the air compressor back and run on the outside pulley groove? I'm sure you would have to deal with new brackets. It is possible to run a shorter single groove pully and clutch.

To answer your question, no...lack of knowledge...this all came from the
PO. Do you have a part number for that bracket?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
good idea with the laser
Need to burp it
Sending unit is from wildhorses....?
and how do you know which way is the correct way?
It doesn't seem hot or burning, but feels warm

Concave side faces the engine. Doesn't matter what side the rivits are on, weather it is electric or mechanical, clutched, flex, or rigid. The concave side of the blades needs to be on the side of the fan that the air is blowing toward.

If the concave side is facing the wrong way (forward) the fan will still move some air, but only a tiny amount of what it should be moving. It will still move it in the correct direction as well, which confuses some people.

This is completely different then "reverse rotation" when is used on most serpentine belt drives where the water pump spins the opposite direction from the crank (due to the belt routing the back side of the belt across the water pump pulley). The concave thing still applies, it is just the blades spin the other way to get the airflow.
 
Top