• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Camber settings

OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
If the camber numbers you got were true, it would look like a road grader going down the road as one tire would be noticeably tipped out at the top while the other would be tipped in about the same amount. Mine had 1.5 degrees positive camber (top sticking out) before I installed shims and it was noticeable.

Yes lol! I know exactly what your saying lol. She does pull hard to the right if I let go of the steering wheel.?:?
 

migs

Sponsor/Vendor
Bronco Guru
Joined
Nov 12, 2011
Messages
1,451
What slednut said.....your tires don't look as drastic as what the numbers show.
Maybe the shop goofed somehow? Is there another place you could try and see what they come up with for comparison? And make sure your tire pressure is equal side to side. A low tire could have an effect on pull.
 
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
Yea migsy I'm gonna take it somewhere else when I have more funds, today cost me $70 for nothin plus $55 for new c bushings, so I'm up to $125 and still don't have the alignment done, sorry I felt the need to vent lol. ?:?:cry:
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Agree with the others that yours does not look out anywhere near 4 degrees. And certainly not with one tire IN at the top and the other one OUT at the top.

And make sure that anyone you take it to for bending the axle tubes can verify that it's indeed an issue with the tubes. I don't think you'd want to compensate by bending tubes when, for instance, it's the steering yokes that are bent.
But I don't think your numbers are accurately reflecting the real world. This would absolutely be worth the 20 bucks for a digital angle gauge that you can use on a rim edge, or rotor face. Or even a hub face, which would at least get you pretty close too.

The images appear to have some wide-angle effect, and perhaps the angle of the camera was not optimal for us to see any camber issues. Maybe take another one just from the front corner of one tire at a time?

That is a beastly lift! Your whole tire is UNDER the truck to the point that it looks from the front at least like your tires are not even into the wheel wells. Almost under the frame rails even!
Be great if you could get those steering link angles down a bit more. But one thing at a time.;)

Good luck with all the testing. By the way, how tall is the lift exactly?
And did you make those spacers for under the front coils?

Paul
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
Throwing this out there. By the front on center pic it looks like you axle is off to the right. This would cause the almost 1/2 degree thrust angle to the left. Also when wheels are pointed straight in relation to rear axle, they are actually turned slightly to the left(offset front axle). With the steering ackriman sp? while going straight the wheels are actually slight steered left. You need to go to a shop that has the old school alignment machine that centers the rear axle to the frame, then measures front axle to rear. The newer style like they used on yours simple measures front to rear axle. I have the same style machine and know an off center front axle showed up as a mis aligned rear axle aka thrust angle.
 
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
Agree with the others that yours does not look out anywhere near 4 degrees. And certainly not with one tire IN at the top and the other one OUT at the top.

And make sure that anyone you take it to for bending the axle tubes can verify that it's indeed an issue with the tubes. I don't think you'd want to compensate by bending tubes when, for instance, it's the steering yokes that are bent.
But I don't think your numbers are accurately reflecting the real world. This would absolutely be worth the 20 bucks for a digital angle gauge that you can use on a rim edge, or rotor face. Or even a hub face, which would at least get you pretty close too.

The images appear to have some wide-angle effect, and perhaps the angle of the camera was not optimal for us to see any camber issues. Maybe take another one just from the front corner of one tire at a time?

That is a beastly lift! Your whole tire is UNDER the truck to the point that it looks from the front at least like your tires are not even into the wheel wells. Almost under the frame rails even!
Be great if you could get those steering link angles down a bit more. But one thing at a time.;)

Good luck with all the testing. By the way, how tall is the lift exactly?
And did you make those spacers for under the front coils?

Paul

Hey Paul, the whole suspension is Wild Horses 5.5 and those front coil buckets came with the long arms I bought from a member here. The steering angle is much better than it was when I had the stock tie rod and drag link. It is now a RuffStuff Heim system with a stock Pittman arm, the angle was way worse when I had a drop Pittman on there.I also had to use spacers to adapt the JK wheels to fit the bronco,those are JK wheels 17X9.
 
Last edited:
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
Throwing this out there. By the front on center pic it looks like you axle is off to the right. This would cause the almost 1/2 degree thrust angle to the left. Also when wheels are pointed straight in relation to rear axle, they are actually turned slightly to the left(offset front axle). With the steering ackriman sp? while going straight the wheels are actually slight steered left. You need to go to a shop that has the old school alignment machine that centers the rear axle to the frame, then measures front axle to rear. The newer style like they used on yours simple measures front to rear axle. I have the same style machine and know an off center front axle showed up as a mis aligned rear axle aka thrust angle.

That's a lot of info for a old guy like me lol. Thank you brother, I'm trying to learn more about this particular type of front end,even though it looks very basic it's turning out to be quite confusing lol.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...It is now a RuffStuff Heim system with a stock Pittman arm, the angle was way worse when I had a drop Pittman on there.

By worse it sounds like you mean the relationship to the trackbar I presume?
I was speaking of the overall angle though, and being a little steep still. Not unworkable steep, but could be better at a shallower angle.
Then once that is achieved the trackbar could have been changed with a riser to better match the draglink angle.

With that much lift, using only a drop bracket typically is not enough to return the angle of the trackbar down to a more normal level.
With 5.5 people often use both the drop and the riser nowadays. Then do whatever it takes to match the two without making the angles worse again.

Sounds like with the dropped pitman arm the draglink angle was better. But then you'd just have to tweak the trackbar to match.
Still have options. But again, verify and fix the camber and caster issues first.
You can fiddle with the angles still if you feel it just doesn't drive right after that.

Paul
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, so the left positive camber # 4.7*means the top of the left tire is tipping to the left, and the right negative
camber # 4.5* means the top of the right tire is also tipping to the left.
As mentioned, it should look much worse.
If you have a carpenters framing square you could stand it up against the tires and eye ball the gap, which would be bigger at the bottom of the left tire, and bigger at the top of the right tire. Since a framing square is not long enough, you could tape a yardstick to it to extend it above the tire.
You could use more caster, but c bushings won't change the camber.
I would be focus on what is causing the camber to be so out of whack.
If you drive on that you will develop saw tooth patterns on the tires.
Good luck
 

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
WOW! Thanks brother! He did mention something about "do you have any shims in there!".



I strongly suspect that shop botched the alignment. Those Camber numbers are crazy and your pictures do not show a truck with serious camber issues.

I haven't seen it happen without being caught by the technician, but it may have been possible that when the lift was set down on the locks prior to alignment, that one side missed a tooth and the technician did not catch it, leaving the whole truck leaning during the alignment. This might explain why the camber numbers are off the same amount in opposite directions.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
That is a beastly lift! Your whole tire is UNDER the truck to the point that it looks from the front at least like your tires are not even into the wheel wells. Almost under the frame rails even!
Be great if you could get those steering link angles down a bit more. But one thing at a time.;)

Paul

He wants huge tires under an uncut Bronco, gotta do what he's gotta do.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890

Attachments

  • DSCN0382.jpg
    DSCN0382.jpg
    72.7 KB · Views: 72
Last edited:
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
He wants huge tires under an uncut Bronco, gotta do what he's gotta do.

Yep, I'm gonna do whatever it takes cuz I built the mofo to be badass and something I wouldve built when I was younger,so the lift, tires ,everything stays that's for dam sure!
 
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
I strongly suspect that shop botched the alignment. Those Camber numbers are crazy and your pictures do not show a truck with serious camber issues.

I haven't seen it happen without being caught by the technician, but it may have been possible that when the lift was set down on the locks prior to alignment, that one side missed a tooth and the technician did not catch it, leaving the whole truck leaning during the alignment. This might explain why the camber numbers are off the same amount in opposite directions.

I suspect you are correct sir. Thank you. ;)
 
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
By worse it sounds like you mean the relationship to the trackbar I presume?
I was speaking of the overall angle though, and being a little steep still. Not unworkable steep, but could be better at a shallower angle.
Then once that is achieved the trackbar could have been changed with a riser to better match the draglink angle.

With that much lift, using only a drop bracket typically is not enough to return the angle of the trackbar down to a more normal level.
With 5.5 people often use both the drop and the riser nowadays. Then do whatever it takes to match the two without making the angles worse again.

Sounds like with the dropped pitman arm the draglink angle was better. But then you'd just have to tweak the trackbar to match.
Still have options. But again, verify and fix the camber and caster issues first.
You can fiddle with the angles still if you feel it just doesn't drive right after that.

Paul

Yes Paul,that is what I was talking about,sorry, I was describing my system just for references sake lol! ;)
 
OP
OP
jmangi62

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
Thank you everyone for the great advice, I will be taking her somewhere else for the front end work, I know a guy who's pretty sharp with this stuff. Jim ;)
 
Top