• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Thoughts on lowering...

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
I have a '76 with a 2" body lift and a 3.5" suspension lift (Duff Monster system with long arms and everything). Currently running 35x12.50s. Truck is cut pretty significantly (unfortunately normally, but maybe good thing here).

I would like to lower the truck as much as I can while maintaining as much capability as I can. She may not be as capable rock crawling, but I'm more interested in trail running at this point. I'm willing to drop down to 33" tires, but I don't think any smaller would look good with my wide cut wheel wells.

I can't really lose the 2" body lift I'm afraid. I'm just worried it's enable too much stuff to fit at this point and seems like a huge PITA to undo.

It looks like I have plenty of room to lose all of the 3.5" of suspension lift, but I'm not sure.

I figure I'll have to swap the drive shafts or have them shortened somehow. What other considerations are there for this?

Here is the current stance:

 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
I have thought of that too I have 1 inch BL and 3.5 SL with 35s
I think I could easily go to a 2.5 inch SL and the 35 would be good , mine is cut from and rear too
I think a SL is less work to change than a BL , you could probably keep the 35 s and go to a 2.5 SL
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
In most scenarios lower is better both off road and on road. Lower Center if gravity is more stable.

Yes. This is why I'm interested in doing this. If you're not crawling over boulders you don't need all the flex and suspension travel. I'm looking for this build to evolve into something faster than it is a rock crawler. Very sound on the street and trail. I like the lower stance on the Stroppe Baja Broncos for instance. And I'm hoping to reuse as much hardware as possible.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Sell it or trade for one closer to what you want. What motor and tranny is in it? I know with a 2"b/l it makes swaps easier and you tend to use those extra 2" for clearance on stuff. Taller shock mounts come to mind. Lowering it may end up far more than you realize
 

okie4570

Contributor
Bronco Guru
Joined
Jul 16, 2012
Messages
9,537
Loc.
NW OK
I've got just a 3.5" and run 36" tires on the rocks. Have done some inner fender trimming and barely rub in the rear when fully flexed, so 35" on 3.5" or 2.5" with no body lift is very doable.
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
Sell it or trade for one closer to what you want. What motor and tranny is in it? I know with a 2"b/l it makes swaps easier and you tend to use those extra 2" for clearance on stuff. Taller shock mounts come to mind. Lowering it may end up far more than you realize

Yeah I'd rather not go that route as I have a lot of blood, sweat, and tears in this one so I'm sentimental. I've literally been over every square inch of this truck and changed (improved) almost everything. The only things I haven't done is paint and body work.

She has a 351w with a mild torquer cam, TBI and HEI dizzy.
NV3550.
Atlas II twin sticked.
Both axles completely rebuilt with 4.56s, ARB lockers, Yukon axles.
Upgraded driveshafts.
Rewired with Painless wiring.
BC Broncos custom dash, wiper cover, and full soft top.
Bailie Bilt custom cage and front and rear bumpers.
10,000lb synthetic lined winch.
Complete interior with insulation, carpet, and Corbeau seats
Hydroboost brakes
Complete steering upgrade with 4x4x2 steering box, Delphi box, etc.
a couple lock boxes, badass stereo, LED lights, etc, etc, etc.

Like many of you guys I have so much (money just being the start!) in this truck. For retarded money I'd sell it, but it's likely easier to just keep going and make her exactly what I want, when I want it. That's the beauty and curse of these old Broncos...lots of options!
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
37's and no lift... still have 5" of uptravel and have done some of the toughest trails/obstacles in the country. Now not quite fair comparing (its got a custom chassis) but is very low. Its just about the amount of work that you are willing to do with the compromises you are willing to make. It kicks it on the highway too, drives as nice as my 2019 SD.
 

Attachments

  • IMG_0461.jpg
    IMG_0461.jpg
    153.9 KB · Views: 172
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
I've got just a 3.5" and run 36" tires on the rocks. Have done some inner fender trimming and barely rub in the rear when fully flexed, so 35" on 3.5" or 2.5" with no body lift is very doable.

I'm more wondering if I can get away with 33/35" tires on 2" BL with little-to-no SL...while maintaining performance. Just want her to squat down a bit and feel more stable at speed.
 

okie4570

Contributor
Bronco Guru
Joined
Jul 16, 2012
Messages
9,537
Loc.
NW OK
I'm more wondering if I can get away with 33/35" tires on 2" BL with little-to-no SL...while maintaining performance. Just want her to squat down a bit and feel more stable at speed.

Gotcha I misread and got mixed up on your intent there in your post.
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
37's and no lift... still have 5" of uptravel and have done some of the toughest trails/obstacles in the country. Now not quite fair comparing (its got a custom chassis) but is very low. Its just about the amount of work that you are willing to do with the compromises you are willing to make. It kicks it on the highway too, drives as nice as my 2019 SD.

yes THIS...this is what I'm trying to accomplish. Performance without the lift. I'm not prepared to go full custom chassis, but probably anything else up to that point. I just don't want to have to take her completely apart again.

A suspension swap I could knock out in a couple hours if it didn't completely wreck all my geometry and lead to a bunch of other changes. That's basically what I'm trying to figure out from all you Bronco geniuses. Figured you got me this far!
 

Slednut10

Contributor
Guru? That's funny!
Joined
Sep 26, 2013
Messages
2,398
Duff's says you need at least a 3" suspension lift to run those long arms. Going back to stock length arms will be a lot of work.
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
Duff's says you need at least a 3" suspension lift to run those long arms. Going back to stock length arms will be a lot of work.

Yeah I saw that and was looking at the truck and wondering why that is. I probably just need to call Duff and talk to them about it. I figured I'd check on here first and see if you guys had any other thoughts I should be considering first. Thanks!
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
The arms start hitting the frame. I know a few running 2-1/2 without issue. But not sure if they did other mods to make it work.

I’ve removed a few body lifts on built trucks. It’s doable but a lot of work. Lots of relocating and massaging stuff to make it all fit. That’s part of why I started with a tub and built the rest from scratch. Had build goals that were not accomplish able any other way
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
The arms start hitting the frame. I know a few running 2-1/2 without issue. But not sure if they did other mods to make it work.

I’ve removed a few body lifts on built trucks. It’s doable but a lot of work. Lots of relocating and massaging stuff to make it all fit. That’s part of why I started with a tub and built the rest from scratch. Had build goals that were not accomplish able any other way

Ah...thank you. This is the kind of reasoning I was looking for. Not happy to hear, but glad I did before trying myself and causing a lot of downtime. My original arms are long gone and I can totally see how changing those arms would be more work than I'm looking to get into on this. I will just stick with what I have. Maybe add sway bars and a wrap trap.

Thanks again...much appreciated!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You did not necessarily get longer driveshafts when you upgraded (most 3.5" lifted EB's don't need longer shafts) so your existing ones might still work.
You can measure and compare to stock and others here, so that's at least something you can figure out. And even if you did need new ones, or have the existing ones shortened, it's not a deal-breaker for the lowering.

Paul
 

bigmuddy

Contributor
Bronco Guru
Joined
Dec 28, 2004
Messages
8,071
Loc.
Marthasville Missouri
37's and no lift... still have 5" of uptravel and have done some of the toughest trails/obstacles in the country. Now not quite fair comparing (its got a custom chassis) but is very low. Its just about the amount of work that you are willing to do with the compromises you are willing to make. It kicks it on the highway too, drives as nice as my 2019 SD.

Yeller, it looks like you are running full width axles?
 

bigmuddy

Contributor
Bronco Guru
Joined
Dec 28, 2004
Messages
8,071
Loc.
Marthasville Missouri
Duff's says you need at least a 3" suspension lift to run those long arms. Going back to stock length arms will be a lot of work.

I run a 2" body lift and a 2" suspension lift with 35" tires. I am happy with the ride and the stability.

I also have the long arms and they will contact the frame when the tire is stuffed which limits up travel, but other than that I haven't had an issue.
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
You did not necessarily get longer driveshafts when you upgraded (most 3.5" lifted EB's don't need longer shafts) so your existing ones might still work.
You can measure and compare to stock and others here, so that's at least something you can figure out. And even if you did need new ones, or have the existing ones shortened, it's not a deal-breaker for the lowering.

Paul

Yeah I have like three sets of driveshafts at this point so I'm hopeful I can swap them around and make something work. This truck came to me on the 5.5" Duff Monster system. I lowered it to 3.5" and now want to go down again. And in between I had a shaft snafu that caused me to end up with a couple extra sets of shafts!
 
OP
OP
J

jlylec

Sr. Member
Joined
Jul 5, 2012
Messages
891
I run a 2" body lift and a 2" suspension lift with 35" tires. I am happy with the ride and the stability.

I also have the long arms and they will contact the frame when the tire is stuffed which limits up travel, but other than that I haven't had an issue.

This is good to hear. It seems like full stuff would happen very rarely and be not a big deal. I just have to figure out if I can lose that 1.5" on the cheap. Is it OK to just remove a couple leafs from an 11-leaf spring pack? either way I'll need new springs up front...and probably shocks.
 
Top